NEMA WD ARCP 1-2016 Automatic Receptacle Control to Meet ASHRAE 90 1-2010 and California Title 24.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationNEMA WD ARCP 1-2016Automatic Receptacle Control to Meet ASHRAE 90.1-2010 and California Title 24A NEMA Wiring Devices Section White Paper WD ARCP 1-2016 Automatic Receptacle Control to Meet ASHRAE 90.1-2010 and California Title 2

2、4 National Electrical Manufacturers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209 www.nema.org 2016 National Electrical Manufacturers Association. All rights including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention fo

3、r the Protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions. National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the developme

4、nt and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. NEMA standards and guideline publications, of which the document contained herein is one, are deve

5、loped through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process and establishes rules to promote fairness in the developm

6、ent of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property

7、, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, express or implied, as to the accuracy o

8、r completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by

9、virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this d

10、ocument should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other s

11、ources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for

12、 safety or health purposes. Any certification or other statement of compliance with any health or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. NEMA WD ARCP 1-2016 Page 1 National Electrical

13、Manufacturers Association Automatic Receptacle Control to Meet ASHRAE 90.1-2010 and California Title 24 Advances in building construction methodology and product technology have allowed for greater energy efficiency in building design than ever before. In the recent past, HVAC and lighting presented

14、 the greatest opportunities to reduce power consumption and conserve energy. Designers and manufacturers have been implementing solutions targeting these systems. Office equipment, appliances, and plug-in lighting loads are the next major area for potential reduction of energy use through management

15、 and control. Today, much of what is plugged into a convenience receptacle is uncontrolled. Based on data from the Energy Information Administration Commercial Buildings Energy Consumption Survey of 2012, approximately 30% of the energy used in buildings is by loads that are plugged in. Both ASHRAE

16、90.10 and California Electric Code (CEC) Title 24 have identified receptacles as an area requiring energy management and have incorporated explicit requirements for automatic control. They target spaces in a building and require that half (50 percent) of the receptacles are controlled by an automati

17、c shutoff device. Most commonly, these are receptacles in personal offices, conference rooms, and cubicle spaces. (Code excerpts shown at the end of the paper) NEMA WD ARCP 1-2016 Page 2 National Electrical Manufacturers Association Below is a typical commercial office building floorplan. In this ex

18、ample, 80 percent of the receptacles are required to be controlled; 20 percent are exempt. Further analysis shows that most receptacles are located in the furniture systems or cubicles and conference areas of offices. Receptacles are most often used to control task lighting, followed by computer per

19、ipherals and personal devices (e.g., portable electronics, chargers, radios, heaters, fans, etc.). The energy standard requires some receptacles to be controlled. The intent is for the controlled receptacles to provide power when needed by the occupantthat is, when the occupant is presentand minimiz

20、e wasted energy. Uncontrolled receptacles continuously supply power to equipment, requiring them to be energized at all times. Most computer equipment utilizes a “sleep mode” to optimize energy efficiency. Since the energy consumption on such a mode is very low, it is suitable to keep these devices

21、plugged in to uncontrolled receptacles. Other, more discretionary plug-in items such as fans, heaters, and radios, if used, should be on only when the occupant is in the area, which results in minimum power use. Circuit Design: Good, Better, Best ASHRAE 90.1 and CEC Title 24 require automatic shutof

22、f control by a time-of-day device, an occupant sensor, or an automated signal from another control or alarm system. It is up to the designer or building engineer to select the most appropriate technique to comply with the standard. Effectiveness and flexibility varies for each of these techniques, a

23、s do the types of buildings. NEMA WD ARCP 1-2016 Page 3 National Electrical Manufacturers Association To better understand plug load, it is critical to examine how a particular building is used. Most commercial buildings serve as work locations, which come alive with people and activity throughout t

24、he day. Every building has prime use times (for example, 8 a.m. to 5 p.m.), with a reduction at night and then a slight increase if nighttime cleaning is performed. With a 24/7 work environment, it may be common to have variable hours, with people working earlier or laternot to mention weekends, hol

25、idays, and occasional exceptions. Many of todays buildings need to be more responsive to the individual worker and modern work schedule. A hardwired load controller can be placed in a series with a branch circuit at the breaker panel to control power to the circuits according to preset schedules. Su

26、ch a controller can be added to the building with minimal changes to the method currently used in circuit design. Either a remotely controllable circuit breaker or remotely controllable relay in a box outside the panel can serve this purpose. Circuits are typically routed conveniently through the bu

27、ilding, properly sized to electrical needs and to maximize the number of outlets on a circuit. As a result, however, one circuit may be used for multiple offices and hallways, possibly unrelated to the way they need to be controlled. Office furniture is typically multi-circuited, with at least two c

28、ircuits per work area, sometimes using isolated ground for computer use. In this instance, using time-based control would facilitate area control but may limit the flexibility of set times. A sensor-based system, such as is commonly used for keeping lights off in unoccupied areas, can turn-off plug

29、loads when the area is unoccupied. Since one person may be at work late or on a weekend when others are not present, ideally this occupant detection should resolve to a single person, not an entire floor or work group. Typical receptacle circuit design may need to be altered for maximum occupant ben

30、efit by limiting it to just a single-person area of use (i.e., only in the office or at the desk where the occupant works). As a result, the power circuit may need to have fewer receptacles, requiring more circuits. For new building construction, more branch circuits can be installed to enable great

31、er control flexibility. For retrofitting existing buildings, wirelessly controlled receptacles can deliver this flexible control. Open cubicle areas require a different design. As open areas need to be controlled as a group, typically a multiple-circuit control makes sense, similar to a time-based s

32、ystem. It can also be triggered by an overhead sensor, adding flexibility if the worker stays late or comes in on the weekend. Again, individually controlled receptacles, rather than controlled branch circuits, provide maximum flexibility and the best user experience. Two Approaches for New Construc

33、tion Applications Controlled branch circuits may offer the use of two circuits for each duplex receptacle, where one receptacle is on one circuit and the other receptacle is on a second circuit (“split wiring”). In this situation, a wired load controller can control one receptacle, while the other r

34、eceptacle is only controlled by the circuit breaker (i.e., always left on and not controlled). Using split wiring for every duplex receptacle will give the user the ability to plug into either a controlled or non-controlled outlet in the same location. The occupant will have choice of continuous pow

35、er or a controlled circuit in the same location. Choosing to run two circuits and control every other receptacle is another technique. The requirement is that a non-controlled receptacle be within 6 feet of a controlled receptacle. NEMA WD ARCP 1-2016 Page 4 National Electrical Manufacturers Associa

36、tion In either case, concern for user convenience needs to be considered to make sure there are enough outlets to meet the plug-in needs of the occupant. Location is key. Receptacle Markings NEC has chosen the symbol to indicate an automatically controlled receptacle. As non-controlled receptacles n

37、ever had an identifier, none is required. Both ASHRAE and the CEC require receptacles to have a permanent marking. The installer may choose to add a permanent marking during construction. There are pre-marked receptacles available from several manufacturers that comply with permanent marking require

38、ments. The overall intent of the energy code and requirement is to minimize wasted energy and maximize efficiency. The directive is to control plug loads through the management of selected outlets. How this is done is left up to the property owner. It is impossible to say whether minimum compliance

39、or a totally integrated building management system is appropriate without understanding the building and its use. Correct sizing in the design is paramount to proper automatic receptacle control. Code Excerpts ASHRAE 90.1-2010 and 2013 8.4.2 Automatic Receptacle Control The following shall be automa

40、tically controlled: a) At least 50% of all 125 volt, 15 and 20 ampere receptacles in all private offices, conference rooms, rooms used primarily for printing and/or copying functions, break rooms, classrooms, and individual workstations b) At least 25% of branch circuit feeders installed for modular

41、 furniture not shown on the construction documents This control shall function on a) a scheduled basis using a time-of-day operated control device that turns receptacles off at specific programmed timesan independent program schedule shall be provided for controlled areas of no more than 5000 ft2 an

42、d not more than one floor (the occupant shall be able to manually override the control device for up to two hours); NEMA WD ARCP 1-2016 Page 5 National Electrical Manufacturers Association b) an occupant sensor that shall turn receptacles off within 20 minutes of all occupants leaving a space; or c)

43、 an automated signal from another control or alarm system that shall turn receptacles off within 20 minutes after determining that the area is unoccupied. All controlled receptacles shall be permanently marked to visually differentiate them from uncontrolled receptacles and are to be uniformly distr

44、ibuted throughout the space. Plug-in devices shall not be used to comply with section 8.4.2. Exceptions: Receptacles for the following shall not require an automatic control device: a) Receptacles specifically designated for equipment requiring continuous operation (24 hours/day, 365 days/year) b) S

45、paces where an automatic control would endanger the safety or security of the room or building occupant(s) California Electric Code (CEC) Title 24 Section 130.5 (d) Circuit Controls for 120-Volt Receptacles. In all buildings, both controlled and uncontrolled 120 volt receptacles shall be provided in

46、 each private office, open office area, reception lobby, conference room, kitchenette in office spaces, and copy room. Additionally, hotel/motel guest rooms shall comply with Item 5. Controlled receptacles shall meet the following requirements, as applicable: 1. Electric circuits serving controlled

47、receptacles shall be equipped with automatic shut-OFF controls following the requirements prescribed in Section 130.1(c)(1 through 5); and 2. At least one controlled receptacle shall be installed within 6 feet from each uncontrolled receptacle or a splitwired duplex receptacle with one controlled an

48、d one uncontrolled receptacle shall be installed; and 3. Controlled receptacles shall have a permanent marking to differentiate them from uncontrolled receptacles; and 4. For open office areas, controlled circuits shall be provided and marked to support installation and configuration of office furni

49、ture with receptacles that comply with Section 130.5(d) 1, 2, and 3; and 5. For hotel and motel guest rooms at least one-half of the 120-volt receptacles in each guest room shall be controlled receptacles that comply with Section 130.5(d)1, 2, and 3. Electric circuits serving controlled receptacles shall have captive card key controls, occupancy sensing controls, or automatic controls such that, no longer than 30 minutes after the guest room has been vacated, power is switched off. 6. Plug-in strips and other plug-in devices that incorporate an occupant sensor shall not be