SAE AMS 3801 3B-2011 Cloth Parachute Meta-Aramid Low Modulus 12 0(407) Weight Special Weave《重量为12 0(407)的特殊编织低模量元纤维降落伞布料》.pdf

上传人:deputyduring120 文档编号:1021167 上传时间:2019-03-21 格式:PDF 页数:4 大小:59.33KB
下载 相关 举报
SAE AMS 3801 3B-2011 Cloth Parachute Meta-Aramid Low Modulus 12 0(407) Weight Special Weave《重量为12 0(407)的特殊编织低模量元纤维降落伞布料》.pdf_第1页
第1页 / 共4页
SAE AMS 3801 3B-2011 Cloth Parachute Meta-Aramid Low Modulus 12 0(407) Weight Special Weave《重量为12 0(407)的特殊编织低模量元纤维降落伞布料》.pdf_第2页
第2页 / 共4页
SAE AMS 3801 3B-2011 Cloth Parachute Meta-Aramid Low Modulus 12 0(407) Weight Special Weave《重量为12 0(407)的特殊编织低模量元纤维降落伞布料》.pdf_第3页
第3页 / 共4页
SAE AMS 3801 3B-2011 Cloth Parachute Meta-Aramid Low Modulus 12 0(407) Weight Special Weave《重量为12 0(407)的特殊编织低模量元纤维降落伞布料》.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2011 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3801/3BAEROSPACEMATERIALSPECIFICATIONAMS3801/3 REV. B Issued 1984-04 Reaffirmed 2001-01 Re

5、vised 2011-06Superseding AMS3801/3A Cloth, Parachute, Meta-Aramid, Low Modulus 12.0(407) Weight, Special Weave RATIONALE This document is being edited to conform to existing formats and submitted for re-affirmation as a result of the 5 year review process. 1. SCOPE 1.1 Form This specification covers

6、 one weight and one weave of low-modulus meta-aramid cloth. 1.2 Application Primarily for use in construction of parachutes. 1.3 Classification 12.0 ounces per square yard (407 g/m2) low-modulus meta-aramid cloth with special weave. 2. APPLICABLE DOCUMENTS See AMS3801. 3. TECHNICAL REQUIREMENTS 3.1

7、Basic Specification The complete requirements for procuring the cloth described herein shall consist of this document and the latest issue of the basic specification, AMS3801. 3.2 Construction and Properties 3.2.1 Yarn Yarn used in weaving the cloth shall be a low-modulus meta-aramid with a carboniz

8、ation (char) temperature not lower than 671 F (355 C). Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3801/3B Page 2 of 4 3.2.1.1 Denier and Filament Count The yarn shall be 200 denier 15 and

9、 shall consist of 100 filaments 10. 3.2.1.2 Ply The yarn shall be 5 ply. 3.2.1.3 Twist The final ply of yarn shall be twisted 2.5 to 2.8 turns per inch (25.4 mm). 3.2.2 Cloth 3.2.2.1 Weave Shall be as shown in Figure 1. 3.2.2.2 Color Shall be Sage Green 1565 as shown in FED-STD-595. The color shall

10、be obtained by the use of melt spun solution dyed yarn. 3.2.2.3 pH Shall be 5.0 to 8.0, incl, determined on the water extract of the finished cloth. 3.2.2.4 Width The width, inclusive of selvage, shall be as ordered. 3.2.2.5 Weight Shall not exceed 12.0 ounces per square yard (407 g/m2).3.2.2.6 Brea

11、king Strength Breaking strength of the unaged cloth shall be not less than 425 pounds force per inch (74 429 N/m) in both warp and fill directions. Breaking strength after heat aging shall be not less than 85% of the unaged values in both the warp and fill directions. 3.2.2.7 Elongation Shall be not

12、 less than 15% in the warp and fill directions. 3.2.2.8 Tearing Strength Shall be not less than 75 pounds force (334 N) in the warp and fill directions. 3.2.2.9 Thickness Shall not exceed 0.032 inch (0.81 mm). Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reprodu

13、ction or networking permitted without license from IHS-,-,-SAE AMS3801/3B Page 3 of 4 3.2.2.10 Air Permeability Shall be 40 to 80 cubic feet per minute for each square foot (12.0 to 24.5 m3/minute for each m2) of surface tested. 3.2.2.11 Count Warp ends and filling picks shall be not less than 38 pe

14、r inch (25.4 mm). 3.3 Length and Put-up The cloth shall be put up in rolls in accordance with AMS3801, paragraph 5.1. Each roll shall contain not less than 80 yards (73 m) nor more than 120 yards (110 m). Each roll shall contain not more than 2 pieces and each piece shall contain not less than 40 ya

15、rds (37 m). 4. QUALITY ASSURANCE PROVISIONS See AMS3801. 5. PREPARATION FOR DELIVERY See AMS3801. 6. ACKNOWLEDGMENT See AMS3801. 7. REJECTIONS See AMS3801. 8. NOTES See AMS3801. PREPARED BY AMS COMMITTEE “P” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3801/3B Page 4 of 4 FIGURE 1 - WEAVE DESIGN Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1