1、AEROSPACE STANDARDPIN, HINGECORROSION RESISTANT STEEL UNS S30200, UNS S30400, OR UNS S31600AS20253Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, phot
2、ocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2000-08REAFFIRMED 2012-11REVIS
3、ED2015-09THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV. BFEDERAL SUPPLY CLASS5315AS20253SHEET 1 OF 2REV.BPROCUREMENT SPECIFICATION: NONESAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely vol
4、untary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your wri
5、tten comments and suggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS20253BRATIONALETHIS LIMITED SCOPE REVISION ADDS REQUIREMENT FOR DIMENSIONS AFTER PLATING TO DRAWING NOTE 2.NOTICETHE INITIAL SAE PUBLICATION OF THIS
6、DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS20253E, NOTICE 2. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THEORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS REL
7、ATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - PINTABLE 1 - DASH NUMBERS AND FDASH NO. F1 .061-.0632 .088-.0903 .116-.1184 .178-.1805 .128-.130AEROSPACE STANDARD AS20253SHEET 2 OF 2REV.BPIN, HINGECORROSION RESISTANT STEEL UNS S30200,
8、 UNS S30400, OR UNS S31600NOTES:NOTICETHIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE.1. MATERIAL: ASTM A313, CLASS 1, TYPE 302, 304, OR 316 (CORROSION RESISTANT STEEL UNS S30200, UNS S30400, ORUNS S3
9、1600), STRAIGHTENED AND CUT LENGTHS.2. FINISH: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, OR PASSIVATE PER AMS2700 AS SPECIFIED. DIMENSIONS APPLY AFTER PLATING.3. LUBRICATION: WHEN SPECIFIED, SOLID FILM LUBRICANT PER MIL-PRF-46010.4. DIMENSIONS IN INCHES.5. REMOVE ALL BURRS AND SHARP EDGES.6.
10、 FOR USE WITH MS20257 AND MS20001 HINGES. AL ALLOY HINGE HALVES: USE CAD. PLATED PIN AND CRES HINGE HALVES: USE PASSIVATED PIN.7. INTERCHANGEABILITY RELATIONSHIP: MS20253 AND AN253 PARTS OF LIKE DASH NUMBERS ARE UNIVERSALLY, FUNCTIONALLY AND DIMENSIONALLY INTERCHANGEABLE.8. EXAMPLE OF PART NUMBER:9.
11、 REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OFTHIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.MS AND AN ARE U.S GOVERNMENT PUBLICATIONS.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
