1、AEROSPACE STANDARD COUPLINGS, CLAMP, GROOVED, V-BAND, 1.75 TO 6.25 FLANGE OD (-65 TO 250 F) AS5355/2 Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,
2、photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1998-09REAFFIRMED 2015-
3、04REVISED2017-03THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A REV.B FEDERAL SUPPLY CLASS 5340 AS5355 /2 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS5355 /1/, /2/, /3/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sc
4、iences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed
5、 stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS5355/2B RATIONALE THIS REVISION CORRECTS THE LOCATION OF THE “B“ DIMENSION AND REVISED TABLE 1. FIGURE 1 - V-BAND
6、COUPLING CLAMP AEROSPACE STANDARD AS5355 /2 SHEET 2 OF 3 REV. B COUPLINGS, CLAMP, GROOVED, V-BAND, 1.75 TO 6.25 FLANGE OD (-65 TO 250 F) TABLE 1 - DIMENSIONS SIZE CODE RANGE B MAX TYPE B B MAX TYPE R D MAX TYPE B D MAX TYPE R BOLT DIA 01-13 2.78 2.78 .80 1.10 .250 14-21 3.03 3.03 .80 1.10 .250 TABLE
7、 2 - DIMENSIONS AND WEIGHTS BASIC NUMBER AS5355/2 SIZE CODE FLANGE OD AS24563 TYPE 2 AXIAL LOAD RATING (LBF) (A) +.03 -.06 C MAX TYPE B C MAX TYPE R RATING TORQUE (LBF-IN) LB/EA MAX TYPE B LB/EA MAX TYPE R 01 1.75 5995 1.88 1.75 1.85 35 .23 .27 02 1.88 6030 2.00 1.80 1.90 35 .24 .28 03 2.00 6060 2.1
8、2 1.85 1.95 35 .25 .29 04 2.12 6090 2.25 1.90 2.00 35 .26 .30 05 2.25 6120 2.38 2.00 2.10 35 .27 .31 06 2.38 6155 2.50 2.05 2.15 35 .27 .31 07 2.50 6185 2.62 2.10 2.20 35 .28 .32 08 2.62 6220 2.75 2.20 2.30 35 .29 .33 09 2.75 6250 2.88 2.25 2.35 35 .30 .34 10 2.88 6280 3.00 2.30 2.40 35 .30 .34 11 3
9、00 6310 3.12 2.35 2.45 35 .31 .35 12 3.12 6345 3.25 2.40 2.50 35 .32 .36 13 3.25 6375 3.38 2.50 2.60 35 .33 .37 14 3.50 6440 3.62 2.60 2.70 35 .35 .39 15 3.75 6505 3.88 2.75 2.85 35 .37 .41 16 4.00 6565 4.12 2.85 2.95 40 .38 .42 17 4.25 6630 4.38 3.00 3.10 40 .40 .44 18 4.75 6755 4.88 3.25 3.35 40
10、43 .47 19 5.25 6880 5.38 3.50 3.60 40 .46 .50 20 5.75 7050 5.88 3.75 3.85 40 .50 .54 21 6.25 7135 6.38 4.00 4.10 40 .53 .57 NOTES /1/ MATERIAL: 300 SERIES STAINLESS STEEL PER PROCUREMENT SPECIFICATION AS5355. /2/ FINISH: PASSIVATE STAINLESS STEEL PER ASTM A967 OR AMS2700. /3/ QUALIFICATION: PRODUCT
11、 SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS5355 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ON-LINE. 4. LATCH ELEMENTS ARE OPTIONAL WITHIN ENVELOPES SHOWN.5. ENVEL
12、OPE DIMENSIONS APPLY WHEN THE COUPLING IS IN THE TIGHTENED CONDITION AT THE MAXIMUM AND MINIMUMPOSITIONS OF ITS DIAMETRICAL RANGE./6/ QUICK RELEASE LATCH COUPLING SHALL CONTAIN ONLY ONE QUICK RELEASE LATCH. THE NUMBER OF RETAINERS PER COUPLING AND THEIR POSITION IS DEPENDENT ON THE SIZE OF THE COUPL
13、ING AND THE LATCH CONFIGURATION. /7/ MARKING: BY ELECTROCHEMICAL ETCHING PER AS478-7A2 OR LASER MARKING PER AS478-15A2. THE COUPLING SHALL BE MARKED WITH SUPPLIER IDENTIFICATION AND AS5355/2-XX PART NUMBER PER AS5355. 8. OPERATING TEMPERATURE: -65 TO 250 F.AEROSPACE STANDARD AS5355 /2 SHEET 3 OF 3 R
14、EV. B COUPLINGS, CLAMP, GROOVED, V-BAND, 1.75 TO 6.25 FLANGE OD (-65 TO 250 F) 9. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.11. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .XXX = .010, .XX = .03,ANG
15、ULAR DIMENSIONS .5.12. EXAMPLE OF PART NUMBER:13. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATINGAREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THISDOCUMENT. AN (R) SYMBOL TO THE LEFT OF T
16、HE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT,INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTSTHAT CONTAIN EDITORIAL CHANGES ONLY.AS5355/2-01 B B = BASIC T-BOLT LATCH COUPLING R = QUICK RELEASE LATCH COUPLING BR = BASIC T-BOLT AND QUICK RELEASE LATCH COUPLING SIZE CODE (FLANGE OD = 1.75) BASIC PART NUMBER
