1、SAETechnicalStandardsBoardRulesprovidethat:“ThisreportispublishedbySAEtoadvancethestateoftechnicalandengineeringsciences.Theuseofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarisingtherefrom,isthesoleresponsibilityoftheuser.”SAErevi
2、ewseachtechnicalreportatleasteveryfiveyearsatwhichtimeitmaybereaffirmed,revised,orcancelled.SAEinvitesyourwrittencommentsandsuggestions.SHEET 1 OF 3MA2113REV.BTHIRD ANGLE PROJECTIONAEROSPACE STANDARDMA2113 REV. BISSUED1985-02REVISED1994-01REAFFIRMED2004-07ADAPTER, ASSEMBLY - PORT CONNECTION RINGLOCK
3、ED TO 60 FLARELESS TUBE END, METRICCUSTODIAN: SAE G-3/G-3B /5/ PROCUREMENT SPECIFICATION: /4/ MA2005 (ISO 7169)FEDERAL SUPPLY CLASS 4730FIGURE 1 - ADAPTER, ASSEMBLYFIGURE 2 - CONFIGURATION FOR SIZES -06, -16, -18 AND -20Copyright 2004 SAE International All rights reserved. No part of this publicatio
4、n may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside U
5、SA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-ADAPTER, ASSEMBLY - PORT CONNECTION RINGLOCKED TO 60 FLARELESS TUBE END, M
6、ETRICAEROSPACE STANDARD MA2113SHEET 2 OF 3MA2113REV.BREV. BTABLE 1A - DIMENSIONSTABLE 1B - DIMENSIONS AND WEIGHTSNOTES:1. MATERIAL:a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS 4928, AMS 4965, OR AMS 4967b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS 5731 OR AMS 57342. HEAT TREATMENT:a. FITTING: 90
7、0 MPa UTS MINb. LOCKRING: 34 TO 40 HRC3. FINISH:a. FITTING: ANODIC TREATMENT PER AMS 2488, TYPE 2b. LOCKRING: PASSIVATE PER QQ-P-35, TYPE IICopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-ADAPTER, ASSE
8、MBLY - PORT CONNECTION RINGLOCKED TO 60 FLARELESS TUBE END, METRICAEROSPACE STANDARD MA2113SHEET 3 OF 3MA2113REV.BREV. BNOTES (Continued):/4/ PROCUREMENT SPECIFICATION: MA2005 (ISO 7169) EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE
9、 ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS./5/ AECMA INTEREST: FUTURE REVISIONS TO THIS STANDARD SHALL BE COORDINATED WITH AECMA C4 COMMITTEE. AECMA IS ASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATERIEL AEROSPATIAL
10、 (PARIS, FRANCE)./6/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT./7/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. LOCKRING EXTERNAL SERRATION DELETED ONE TOOTH FOR METRIC IDENTIFICATION PURPOSE.8. IDENTIFICATION PER AS478 CLASS 35D. NAME, TRADEMARK OR CAGE CODE,
11、 AND PART NUMBER.9. WORKING PRESSURE: THIS PART IS DESIGNED FOR USE IN 28 000 kPa WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM.10. ADAPTERS TO BE INSTALLED PER MA2114 INTO BOSS CAVITIES PER MA2110.11. INTERPRETATION OF DRAWING PER MAP4296.12. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMEN
12、TS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 3.2 m Ra AND SEALING SURFACE TO BE 1.6 m Ra.13. BREAK EDGES .08 TO .38 UNLESS OTHERWISE SPECIFIED.14. DIMENSIONING AND TOLERANCING: ANSI Y14.5M15. DIMENSIONS IN MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .13, ANGULAR DIMENSIONS 5./16/ EXAMPLE OF PART NUMBER:Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
