1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23440-9 SANS 24735:2009Edition 1ISO/IEC 24735:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Information technology Office equipment Method
4、for measuring digital copying productivity This national standard is the identical implementation of ISO/IEC 24735:2009 and is adopted with the permission of the International Organization for Standardization and the International Electrotechnical Commission. Published by SABS Standards Division 1 D
5、r Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 24735:2009 Edition 1 ISO/IEC 24735:2009 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC
6、 71, Information technology, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in December 2009. Reference numberISO/IEC 24735:2009(E)ISO/IEC 2009INTERNATIONAL STANDARD ISO/IEC24735First edition2009-03-
7、01Information technology Office equipment Method for measuring digital copying productivity Technologies de linformation quipements de bureau Mthode de mesure de la productivit dun photocopieur numrique SANS 24735:2009This s tandard may only be used and printed by approved subscription and freemaili
8、ng clients of the SABS .ISO/IEC 24735:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perf
9、orming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this P
10、DF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central
11、Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission
12、 in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2009 All rights reserv
13、edSANS 24735:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24735:2009(E) ISO/IEC 2009 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Test Param
14、eters and Conditions. 3 4.1 Environment 3 4.2 Voltage . 3 4.3 Copying Device Setup 3 4.4 Paper 4 4.5 Maintenance 4 4.6 Preparation of Test Targets (Test Charts) 4 5 Test Method. 5 5.1 Test Setup 5 5.2 Test Measurement Procedure . 5 5.3 Test Method Process 8 5.3.1 Suggested Test Method Process Flow C
15、hart 8 5.3.2 Estimating the Set Count . 8 5.3.3 5% Consistency Criteria. 9 5.4 General Performance Test . 10 5.5 Feature Performance Test . 11 6 Calculations and Treatment of Data . 14 6.1 General Performance Test . 14 6.1.1 1 Set Test . 14 6.1.2 1 Set + 30 Seconds Test. 15 6.1.3 1 Set + 4 Minutes T
16、est 15 6.2 Feature Performance Test . 16 6.2.1 1 Set Test . 16 6.2.2 1 Set + 30 Seconds Test. 16 7 Presentation of Results 17 7.1 General Performance Test . 17 7.2 Feature Performance Test . 18 Annex A (informative) Examples of report presentation 20 Annex B (informative) Example of full detailed re
17、port . 23 Annex C (normative) Test targets for measurement of copying productivity . 26 Annex D (informative) Definitions of “FCOT” and “Continuous Copying Speed” 27 Bibliography . 30 SANS 24735:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the S
18、ABS .ISO/IEC 24735:2009(E) iv ISO/IEC 2009 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participat
19、e in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and
20、 non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The m
21、ain task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies cas
22、ting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 24735 was prepared by Technical Committee ISO/TC JTC1, Information techn
23、ology, Subcommittee SC 28, Office equipment. SANS 24735:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24735:2009(E) ISO/IEC 2009 All rights reserved vIntroduction Many digital copying devices produce copied pages at a different
24、rate than their nominal speed when running with different modes (simplex, duplex, copying quality modes), different substrate weight and collating and/or finishing options. The degree to which a reduction in productivity is experienced depends significantly on other parameters of the job stream. The
25、 most dominant of the parameters of the job stream are: (the number of original pages in a set to be printed, single-sided or double-sided output pages, image quality modes selected, B first copy out time”. This “FCOT” and “continuous copying speed” for EP (electrophotographic) copying machine is de
26、fined in ISO/IEC 21117. For reference, the extension of these definitions also applied for out of scope copying devices is shown in Annex D (informative). 3.6 full detailed report presentation of information including machine setup and measured test results 3.7 full report presentation of results in
27、cluding the FSOT, ESAT and EFTP values in general performance test or the FSOT and ESAT values in feature performance test as well as the calculated averages for each values 3.8 general performance test test used to evaluate productivity by providing FSOT, ESAT and EFTP without using any special fea
28、ture or mode, and includes both the simplex copying mode and the duplex copying modes of 1:2 and 2:2 if available 3.9 LSOT last set out time number of seconds between the initiation of the job to the complete exit of the last page of the last test set 3.10 nominal copying speed copying rate, excludi
29、ng time to first page copied, and measured when producing pages in a continuous copying mode with a single static document using a nominal weight substrate NOTE Nominal copying speed is expressed in copies per minute or images per minute. 3.11 simplex copying use of a copying device when only a sing
30、le side of a sheet is copied on NOTE Other equivalent terms are “one-sided copying” or “simplex to simplex” (referred as 1:1 mode). SANS 24735:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24735:2009(E) ISO/IEC 2009 All rights r
31、eserved 33.12 summary report presentation of results including the average overall FSOT and ESAT in general performance test or the ratio of the copying performance such as FSOT and ESAT with the subject feature ON versus the copying device default base line performance (without the subject feature
32、ON) in feature performance test 3.13 test file refers to digital file used for creating test targets 3.14 test set all of the pages of test target 3.15 test target hardcopy document used for testing per the test method, created from the test file NOTE An equivalent term is “test chart”. 4 Test Param
33、eters and Conditions 4.1 Environment The test environment, including temperature and humidity, shall be within the ranges recommended by the manufacturer for operating the device. If no recommendation is available, the following ranges shall apply. Temperature: 18 C to 25 C Relative humidity: 30 % t
34、o 70 % NOTE The temperature and humidity ranges of the test environment should be recorded in the full detailed report (Annex B). 4.2 Voltage The copying device shall be connected to a voltage supply within the manufacturer specified operating voltage range for the copying device under test. NOTE Th
35、e measurement should be made under no-load condition prior to each test. 4.3 Copying Device Setup Place the copying device on a horizontal surface and set up the copying device according to the manufacturers recommendations. The copying device shall be fully enclosed in its normal exterior cover. Th
36、e machine and all of its necessary supplies shall be acclimated in the test environment prior to conducting the test(s). All supplies used in the test(s), included copy paper, shall be those specified by the manufacturer. All image and copying modes should be at their factory pre-set configuration f
37、or the copying device. It is assumed that the settings listed in table 1 are common to all copying devices. These listed settings shall be set to the manufacturers default or pre-set condition for the device. If a device has settings not listed in Table 1, they too shall be set to default settings.
38、For copying devices that have additional print quality and digital image processing features, those features must be set to match their normal default condition, and included in the result reporting. Disabling manufacturer default installed features, routines or applications, is not allowed. Example
39、s include, but are not limited to the following: automatic cleaning or calibration cycles, and energy save settings. If the system has automatic media detect(automatic paper type selection), it can be disabled, and paper used in the test shall be SANS 24735:2009This s tandard may only be used and pr
40、inted by approved subscription and freemailing clients of the SABS .ISO/IEC 24735:2009(E) 4 ISO/IEC 2009 All rights reservedselected manually. This must be noted in the full detailed report (Annex B). The following pre-set values in the test will be noted on this report format. Table 1 Pre-set Setti
41、ngs Pre-set item Pre-set value Output resolution default Output Quality default Copying mode default Auto density adjustment default Mode Collating function Activated (if not activated in default mode.) Paper sending direction default Paper Paper type setting default Paper feeding Standard cassette
42、Paper exit Standard exit tray Face up exit default Paper-path Duplex copying unit default (used in 1:2 mode and 2:2 mode). Fixing capability default Image quality stability default Capacity of paper default Temporary stop Others default NOTE If the copying device is setup with external options such
43、as sorter or finisher as default, then these options shall be noted on the full detailed report format in corresponding column in Annex B, for example “Finisher as default”. 4.4 Paper The output paper used in this test shall be within the range of, and/or not violate, specific written attribute guid
44、elines and recommendations provided by the copying device manufacturer, which may include but are not be limited to: size, weight, composition, paper manufacturer(s), paper type, part number and other physical characteristics. Care must be taken to use a paper that conforms to the copying device man
45、ufacturers paper specifications for the default copying device settings. The paper used for the general performance test section 5.4 shall be cut-sheet, A4 and/or 8.5“x11“ size. Optional paper sizes may be used in the feature performance tests such as 8.5“x14“, A3, and/or 11“x17“ size as appropriate
46、 for the test mode. The paper manufacturer, weight, size and paper type/name used in each test shall be noted on the full detailed report. NOTE When you use the papers other than A4/A3, then you should state each paper size in the places of A4 and A3 at the presentation of results. And you should us
47、e the same paper size by each machine when you want to compare the productivity results of one machine with other machines. If the copying device is used in “thick paper mode” for copying, then this optional mode shall be noted on the full detailed report format in corresponding column in Annex B. 4
48、.5 Maintenance Copying device maintenance shall be performed throughout testing per the manufacturers recommendations on an as needed basis. (For example, cleaning routines or consumables replacement). 4.6 Preparation of Test Targets (Test Charts) The copying test file is outlined in Annex C (normat
49、ive). This test file is from ISO/IEC 24734 “Method of measuring digital printing productivity“. The test target consists of 4 single sided pages. When using the test target for the copying productivity test, the copying target must SANS 24735:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24735:2009(E) ISO/IEC 2009 All rights reserved 5be created by printing the most recent electronic test file. If the intended machine does not have a printer function, th
