1、 IEC 60317-0-9 Edition 1.0 2015-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 0-9: General requirements Enamelled rectangular aluminium wire Spcifications pour types particuliers de fils de bobinage Partie 0-9: Exigences gnrales Fil de secti
2、on rectangulaire maill en aluminium IEC 60317-0-9:2015-05(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mecha
3、nical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the add
4、ress below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la phot
5、ocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC
6、 de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes Internatio
7、nal Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue -
8、 webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searc
9、hpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publication
10、s. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivale
11、nt terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued sin
12、ce 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos d
13、e lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC es
14、t constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications tec
15、hniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). El
16、le donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par
17、email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique Int
18、ernational (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 60 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37,
19、 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60317-0-9 Edition 1.0 2015-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types
20、 of winding wires Part 0-9: General requirements Enamelled rectangular aluminium wire Spcifications pour types particuliers de fils de bobinage Partie 0-9: Exigences gnrales Fil de section rectangulaire maill en aluminium INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNAT
21、IONALE ICS 29.060.10 ISBN 978-2-8322-2667-4 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que v
22、ous avez obtenu cette publication via un distributeur agr. 2 IEC 60317-0-9:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms, definitions, general notes and appearance . 7 3.1 Terms and definitions 7 3.2 General notes . 7 3.2.1 Methods of test 7 3.2.2 Wi
23、nding wire 8 3.3 Appearance 8 4 Dimensions 8 4.1 Conductor dimensions 8 4.2 Tolerance on conductor dimensions 9 4.3 Rounding of corners 9 4.4 Increase in dimensions due to the insulation . 11 4.5 Overall dimensions . 11 4.5.1 Nominal overall dimensions . 11 4.5.2 Minimum overall dimensions 11 4.5.3
24、Maximum overall dimensions . 11 5 Electrical resistance 12 6 Elongation . 12 7 Springiness . 12 8 Flexibility and adherence . 12 8.1 Mandrel winding test . 12 8.2 Adherence test 12 9 Heat shock 12 10 Cut-through . 12 11 Resistance to abrasion 13 12 Resistance to solvents . 13 13 Breakdown voltage 13
25、 14 Continuity of insulation 13 15 Temperature index 13 16 Resistance to refrigerants 13 17 Solderability 14 18 Heat or solvent bonding . 14 19 Dielectric dissipation factor 14 20 Resistance to transformer oil . 14 21 Loss of mass . 14 23 Pin hole test 14 30 Packaging . 14 Annex A (informative) Nomi
26、nal cross-sectional areas for preferred and intermediate sizes . 15 Annex B (informative) Special tolerances . 24 IEC 60317-0-9:2015 IEC 2015 3 Bibliography 25 Table 1 Conductor tolerances . 9 Table 2 Nominal cross-sectional areas of preferred sizes . 10 Table 3 Corner radii . 11 Table 4 Increases i
27、n dimensions 11 Table 5 Mandrel winding 12 Table 6 Breakdown voltage 13 Table A.1 Nominal cross-sectional areas (1 of 9) . 15 Table B.1 Overall dimensional tolerances for grade 2 24 4 IEC 60317-0-9:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDI
28、NG WIRES Part 0-9: General requirements Enamelled rectangular aluminium wire FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
29、international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (her
30、eafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also pa
31、rticipate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible,
32、 an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While a
33、ll reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to a
34、pply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation o
35、f conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this p
36、ublication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indire
37、ct, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the
38、correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-0-9 has been prep
39、ared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on voting 55/1519/FDIS 55/1525/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This pu
40、blication has been drafted in accordance with the ISO/IEC Directives, Part 2. The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. IEC 60317-0-9:2015 IEC 2015 5 A list
41、 of all parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site
42、 under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 IEC 60317-0-9:2015 IEC 2015 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wir
43、es used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851 series); 2) Specifications for particular types of winding wires (IEC 60317 series); 3) Packaging of winding wires (IEC 60264 series). IEC 60317-0-9:2015 IEC 2015 7 SPECIFIC
44、ATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-9: General requirements Enamelled rectangular aluminium wire 1 Scope This part of IEC 60317 specifies the general requirements of enamelled rectangular aluminium winding wires. The range of nominal conductor dimensions is given in the relevant spec
45、ification sheet. When reference is made to a winding wire according to a standard of the IEC 60317 series mentioned under Clause 2, the following information is given in the description: reference to IEC specification; nominal conductor dimensions in millimetres (width thickness); grade. EXAMPLE IEC
46、 60317-16 4,00 x 1,00 Grade 1 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced
47、 document (including any amendments) applies. IEC 60172 1 , Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires IEC 60317-0-1, Specifications for particular types of winding wires Part 0-1: General requirements Enamelled round copper wire IEC 608
48、51 (all parts), Winding wires Test methods ISO 3, Preferred numbers Series of preferred numbers 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60317-0-1 apply. 3.2 General notes 3.2.1 Methods of t
49、est All methods of test to be used for this standard are given in IEC 60851. _ 1Fourth edition to be published. 8 IEC 60317-0-9:2015 IEC 2015 The clause numbers used in this standard are identical to the corresponding test numbers in the IEC 60851 series of standards. In case of inconsistencies between the publication on methods of test and this standard, IEC 60317-0
