1、 ISO 2013 Fire detection and alarm systems Part 23: Visual alarm devices Systmes de dtection et dalarme dincendie Partie 23: Dispositifs dalarme visuels INTERNATIONAL STANDARD ISO 7240-23 First edition 2013-01-15 Reference number ISO 7240-23:2013(E) ISO 7240-23:2013(E)ii ISO 2013 All rights reserved
2、 COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address
3、below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 7240-23:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword
4、iv Introduction vi 1 Scope . 1 2 Normative references 1 3 T erms, definitions and abbr e viations 2 3.1 Terms and definitions . 2 3.2 Abbreviations . 3 4 Requirements 3 4.1 Compliance . 3 4.2 Device class 3 4.3 Minimum and maximum effective light intensity . 4 4.4 Light colour 4 4.5 Light pattern an
5、d frequency of flashing 4 4.6 Durability . 4 4.7 Construction 4 4.8 Manufacturers adjustments . 5 4.9 On-site adjustment of mode or behaviour 5 4.10 Marking and data 5 4.11 Additional requirements for software controlled visual alarm devices 7 4.12 Synchronization Optional function 8 5 Tests . 8 5.1
6、 General . 8 5.2 Reproducibility 10 5.3 Variation of effective luminous intensity.11 5.4 Operational performance11 5.5 Durability 12 5.6 Dry heat (operational) .12 5.7 Dry heat (endurance) .13 5.8 Cold (operational) .14 5.9 Damp heat, cyclic (operational) 15 5.10 Damp heat, steady-state (endurance)
7、16 5.11 Damp heat, cyclic (endurance) .17 5.12 Sulfur dioxide (SO 2 ) corrosion (endurance) 18 5.13 Shock (operational) .19 5.14 Impact (operational) .20 5.15 Vibration, sinusoidal (operational) 21 5.16 Vibration, sinusoidal (endurance) 22 5.17 Electromagnetic compatibility (EMC), immunity (operatio
8、nal) .23 5.18 Enclosure protection .24 5.19 Flash synchronisation testing (optional function) 26 6 Test report 27 Annex A (normative) Method for measuring the lig ht distribution fr om a visual alarm de vic e 29 Annex B (normative) Comparative light output level measurement for visual alarm devices
9、36 Annex C (informative) C onstruction of the lig ht t est chamber and associat ed equipment for comparative measurements 38 Annex D (informative) C omparison of flammability t est r equir ements 40 Bibliogr aph y .42 ISO 7240-23:2013(E) Foreword ISO (the International Organization for Standardizat
10、ion) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be r
11、epresented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards
12、 are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internat
13、ional Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7240-23 wa
14、s prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subcommittee SC 3, Fire detection and alarm systems. ISO 7240 consists of the following parts, under the general title Fire detection and alarm systems: Part 1: General and definitions Part 2: Control and i
15、ndicating equipment Part 3: Audible alarm devices Part 4: Power supply equipment Part 5: Point-type heat detectors Part 6: Carbon monoxide fire detectors using electro-chemical cells Part 7: Point-type smoke detectors using scattered light, transmitted light or ionization Part 8: Carbon monoxide fir
16、e detectors using an electro-chemical cell in combination with a heat sensor Part 9: Test fires for fire detectors Technical Specification Part 10: Point-type flame detectors Part 11: Manual call points Part 12: Line type smoke detectors using a transmitted optical beam Part 13: Compatibility assess
17、ment of system components Part 14: Guidelines for drafting codes of practice for design, installation and use of fire detection and fire alarm systems in and around buildings Technical Report Part 15: Point type fire detectors using scattered light, transmitted light or ionization sensors in combina
18、tion with a heat sensor Part 16: Sound system control and indicating equipment Part 17: Short-circuit isolators Part 18: Input/output devicesiv ISO 2013 All rights reserved ISO 7240-23:2013(E) Part 19: Design, installation, commissioning and service of sound systems for emergency purposes Part 21: R
19、outing equipment Part 22: Smoke detection equipment for ducts Part 23: Visual alarm devices Part 24: Sound-system loudspeakers Part 25: Components using radio transmission paths Part 27: Point-type fire detectors using scattered-light, transmitted-light or ionization smoke sensor, an electrochemical
20、 cell carbon-monoxide sensor and a heat sensor Part 28: Fire protection control equipment ISO 2013 All rights reserved v ISO 7240-23:2013(E) Introduction The purpose of a visual fire alarm device is to warn person(s) within, or in the vicinity of, a building of the occurrence of a fire emergency in
21、order to enable such person(s) to take appropriate measures. This part of ISO 7240 allows manufacturers to specify visual alarm devices in terms of the range at which the required illumination is met. Three classes of device are defined, one for ceiling mounted devices, one for wall mounted devices
22、and an open class. The maximum range of the visual alarm device is tested by measuring the light output in a part of the hemisphere surrounding it to determine its light distribution. As the light output of some visual alarm devices can change over time due, for example, to the effect of self-heatin
23、g, a specific test checks that the variation of light output over time is within acceptable limits. This part of ISO 7240 gives common requirements for the construction and robustness of visual alarm devices as well as for their performance under climatic, mechanical and electrical interference cond
24、itions which are likely to occur in the service environment. Visual alarm devices can be classified in one of three application environment types.vi ISO 2013 All rights reserved INTERNATIONAL ST ANDARD ISO 7240-23:2013(E) Fire detection and alarm systems Part 23: Visual alarm devices 1 Scope This pa
25、rt of ISO 7240 specifies the requirements, test methods and performance criteria for visual alarm devices in a fixed installation intended to signal a visual warning of a fire between a fire detection and alarm system and occupants in and around buildings. This part of ISO 7240 specifies visual alar
26、m devices for three types of application environment. It is only applicable to pulsing or flashing visual alarm devices, for example xenon beacons or rotating beacons. It is not applicable to devices giving continuous light output. This part of ISO 7240 is not intended to cover visual indicators, fo
27、r example, on detectors or on the control and indicating equipment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced doc
28、ument (including any amendments) applies. ISO 2813:1994, Paints and varnishes Determination of specular gloss of non-metallic paint films at 20 degrees, 60 degrees and 85 degrees ISO 7240-1, Fire detection and alarm systems Part 1: General and definitions ISO/CIE 23539:2005, Photometry The CIE syste
29、m of physical photometry IEC 60068-1:1988, Environmental testing Part 1: General and guidance IEC 60068-2-1:2007, Environmental testing Part 2-1: Tests Test A: Cold IEC 60068-2-2:2007, Environmental testing Part 2-2: Tests Test B Dry heat IEC 60068-2- 6:2007, Environmental testing Part 2-6: Tests Te
30、st Fc: Vibration (sinusoidal) IEC 60068-2-27:2008, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock IEC 60068-2-30:2005, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle) IEC 60068-2-42:2003, Environmental testing Part 2-42: Tests Test Kc: Sulphu
31、r dioxide test for contacts and connections IEC 60068-2-75:1997, Environmental testing Part 2-75: Tests Test Eh: Hammer tests IEC 60068-2-78:2001, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60529:2001, Degrees of protection provided by enclosures (IP Code) IEC 60695
32、11-10:2003, Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods ISO 2013 All rights reserved 1 ISO 7240-23:2013(E) IEC 60695-11-20:2003, Fire hazard testing Part 11-20: Test flames 500 W flame test methods EN 50130-4:2011, Alarm systems Part 4: Electromagneti
33、c compatibility Product family standard: immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems UL 94, Standard for Safety of Flammability of Plastic Materials for Parts in Devices and Appliances testing 3 T erms, d efinitions and abbr e viatio
34、ns For the purposes of this document, the terms, definitions and abbreviations given in ISO 7240-1 and the following apply. 3.1 T erms and definiti ons 3.1.1 coverage volume volume within which the required illumination is achieved 3.1.2 class C visual alarm device device intended for mounting on ce
35、ilings 3.1.3 class O visual alarm device device where the mounting is specified by the manufacturer 3.1.4 class W visual alarm device device intended for mounting on walls 3.1.5 normal axis axis normal to the mounting plane which passes through the reference point 3.1.6 mode (of operation) one of a
36、possible number of pre-defined light outputs selected by means specified by the manufacturer 3.1.7 reference point optical centre within or on the surface of the visual alarm device specified by the manufacturer 3.1.8 required illumination illumination of 0,4 lm/m 2on a surface perpendicular to the
37、direction of the light emitted from the device 3.1.9 type A visual alarm device device primarily intended for conditioned indoor applications Note 1 to entry: In certain climates, a Type A visual alarm device may be suitable for some unconditioned indoor areas such as an enclosed attached garage or
38、some protected outdoor areas such as under an awning. 3.1.10 type B visual alarm device device primarily intended for unconditioned indoor or outdoor applications Note 1 to entry: A Type B visual alarm device may be more suitable than a Type A visual alarm device for some conditioned indoor areas wh
39、ere high temperature and/or humidity are present.2 ISO 2013 All rights reserved ISO 7240-23:2013(E) 3.1.11 type C visual alarm device device primarily intended for harsh environment applications Note 1 to entry: Type C visual alarm devices are specifically intended for use in extreme climates and ar
40、eas were harsh environment exists, e.g. mining, including open-cast mining. 3.1.12 visual alarm device v.a.d device which generates a flashing light to signal to the occupants of a building that a fire condition exists 3.2 A bbr e viations a.c. alternating current d.c. direct current r.m.s. root mea
41、n square v.a.d. visual alarm device 4 Requirements 4.1 Compliance In order to comply with this part of ISO 7240, the v.a.d. shall meet the requirements of Clause 4, which shall be verified by visual inspection or engineering assessment, shall be tested as described in Clause 5 and shall meet the req
42、uirements of the tests. 4.2 Device class 4.2.1 The v.a.d shall meet the requirement for coverage volume of at least one of the following three classes: a) C, ceiling mounted devices; b) W, wall mounted devices; c) O, open class devices. 4.2.2 Class C devices shall be further specified as C-x-y (see
43、4.10 2 d) 1), where: x is the maximum height, in metres, between 2,5 m and 10 m at which the device may be mounted, and y is the diameter, in metres, of the coverage cylindrical volume when the device is mounted at the ceiling height. EXAMPLE C-3-12 refers to a ceiling mounted device, with a maximum
44、 mounting height of 3 m, providing a cylindrical volume of 12 m diameter. NOTE If a C-3-12 is located at the centre of square, it corresponds to a square coverage range (8.49 8.49) m contained within a circle of 12 m diameter. 4.2.3 Class W devices shall be further specified as W-x-y (see 4.10 2 d)
45、2), where: x is the maximum height of the devices on the wall, in metres, with a minimum value of 2,4 m, and y is the width of a square room, in metres, covered by the device. ISO 2013 All rights reserved 3 ISO 7240-23:2013(E) EXAMPLE W-2.4-6 refers to a wall mounted device, with a maximum mounting
46、height of 2,4 m, providing a coverage volume of (2,4 6 6) m. 4.2.4 For class O devices the coverage volume in which the required illumination is achieved shall be specified (see 4.10 2 d) 3). 4.3 Minimum and maximum effective light intensity When tested in accordance with 5.4, the v.a.d. shall produ
47、ce an effective light intensity of at least 1 cd for 70 % of all measurement points and shall not exceed 500 cd for any measurement points. 4.4 Light colour The v.a.d. shall emit a white or red flashing light. 4.5 Lig ht patt ern and fr equency of flashing The flash rate of the v.a.d. shall be betwe
48、en 0,5 Hz and 2 Hz measured between the 10 % of peak values of consecutive leading edges of the pulses (P 10L ). NOTE The frequency of flashing may vary in different countries. Reference needs to be made to local regulations. Some countries have adopted the ISO 8201 temporal pattern. The maximum on-
49、time, measured between the 10 % of peak values of the leading edge ( P 10L ) and trailing edge (P 10T ) of the pulse shall not exceed 0,2 s. If the light emitted consists of groups of several pulses and if the time between the P 10Tof one pulse and the P 10Lof the next pulse is less than 0,04 s then the pulses shall be considered as a single event. Any set of multiple pulses shall not exceed 0,2 s between the P 10
