1、LUC : Key words : , prEN 3659: Ecjition 1 . .- ill supersede edition xx- 19xc , AECk!A/C 3 (Secr 469 4 no - i989 - Study : D 92-1 Supersebe5 c 3 - xxxx Aerospace series Titanium/Columbium solid rivets Technical speci fica tion I Srie a6rospatiale ci cs Test method 4.1 Material Shall ,conform with th
2、e tequire- ments of the material standard quoted in the document defini ng the rivet. See material specification. 4.2 Dimensions Shall conform with the require- ments of the document defining the r vet. Methods are at manufacturers option. In case of dispute the projection method wi 11 be used as th
3、e reference method, using x25 magnification for di ameters up to 6 mn and x10 for greater diameters. This inspection shall be car- ried out at 3 equidistant points around the rivet. .4.3 Shall, conform to-the condition of use defined in the material standard specification required by the product sta
4、ndard. Heat treatment need not be carried out if the rivet already sa- tisfies the properties required by thi s speci fi cati on. See clause 4.5. hHeat treatment Surface treatment Shall conform with the docu- ment defining the rivet. Methods are at manufacturer* opti on. 4.4 4.5 - 4.5.1 Mechanical p
5、roperties Shall be checked by a double shear test. Double shear Non-assembled rivets (i.e. rr thout post-formed head) shall meet the values specified in table 4. See IS0 9417. If rivets are not long enough for double shear test, testing shall be carried out 01) test ; Ni res .- . Table 3 c Copyright
6、 Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-J . Surface .- condition Identification by marking * Rivets shall be free from seams, burrs, laps, crevices, inc
7、rustations, clefts, tool i ng narks, scores, cracks and other defects prejudicial to the use of the rivet. Each rivet shall be marked in conformity with the defining document, except for particulai requested by the user. No sharp edges or other defect detrimental to the correct setting of the rivet
8、shall be present. C1 ause 4.5.2 .- 4.5.3 4.6. 4 .? . AECMA PREN3b59 49 m LOL23LZ 0006170 O m ?rEh 3659 Page 5 Table 1 - Technical requirements ond test rnkthods (continued) I Characteristics Upset test fechni cal requirements After upset the head of the rivet shall be free from cracks or folds when
9、viewed at magnification of x 10. Grain size After any thermal treatment thc longitudinal grain size shell be 4 or finer. Test method Rivets shall be placed in a test fixture substantial fy conforming to figure 1 a. The free end of the rivet shall be upset using a flat too1 to obtain a head confor- m
10、ing to the requirements of figure 1 b. Micro examination of longitu- dinal section and comparison with ASTM-Ell2 (XI O0 magni fi - cati on). Rivets shall be examined visually with or without magnification. Magnification is limited to x6. to x6. Vi sua1 examination. Sampl e size Table 3 his test to ,
11、e performed only et the request of :he purchaser . Table 3 Table 2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN3659 89 LOL23LL 0006L71 2
12、prEN 3659 Page 6 C1 ause 4.8 - 4.9 Table 1 - Technical requirements and -test methods (continued) :haracteristics Packing Labelling Technical requirements Rivets shall be delivered in strong and durable packages, capable of protecting them from physjcal and corrosi ve deterioration. Any particular o
13、r additional parcka- ging requi rements shall be specified in the order. If the rivets delivered come from different lots, they shall bepacka- ged and identified separatefy. Unless particularly specified in the order, the number of rivets in the same pa- ckage is left to the manufacturers discretion
14、. However, maximum mass is 25 kg. A copy of the manufacturers deli- very note relating to the rivet lot shall be included in the package but may, on the other hand, be sent separately on request. Durable external labels on the package shall contain the following information - complete reference numb
15、er of the standard rivet j - quantity (mass or number of rivets) j - manufacturers identity, name and address j - number of manufacturing lot j - manufacturers inspection stamp. Labels attached to a secondary packzge shall include the following information as a minium : - complete referencenumber of
16、 the rivet ; - quantity i - lot number ; - inspecton stamp. - Test method Sarpl e sfie 027Mh0189T4 89;78433= Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IH
17、S-,-,-AECMA PREN3657 87 N 10123L1 000b172 4 N . Number of rivets in the lot 151 to 280 Number of rivets to be taken for tlie sampling lot 32 281 to 500 . 50 501 to : 200 80 1 201 to 3 200 125 3 201 to 10 O00 200 c 35 001 to 150 O00 500 Number of rivets to be taken for the sampling lot . 5. 5 5 8 8 8
18、 13 Number of defective rivets which lead to . rejection of the lot (11 1 1 1 1 1 1 1 t. .? prES 3659 Fsbe 7 Tzble 2 - Sampling plan srd acceptaxe leves Mon dertrirctive tests Maximum number .of defective rivets in the sampling lot which permit acceptance of the lot (11 , 3 7 10 14 21 21 (1) Defecti
19、ve rivets shall not be returned to the lot. Table 3 - Sampling plan and rejection levels Number of rivets in the lot * 151 to 280 281 to 500 501 to 1 200 I 1 201 to 3 200- 3 201 to 10 O00 10 O01 to 35 O00 35 001 to 150 O00 (il If the reason for rejection results from the method of operatirig the tes
20、t apparatus or from faulty heat treatment which can be rectified in a satis- factory maiincr, the tests may be repeated after elimination of the rejection cause, A note to this effect shall be added to the corresponding insbection documents. Heit treatment nay only be repeated once. If the mechartic
21、al prcperties are still unsatisfhctory, the lot shall be rejected. . r 8 9 / 784 3 7s 0278hlP1018ST4 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AE
22、CMA PREN3b57 87 m 3032313 0006373 b m _- Table 4 - Shear sti-wsth b!ominal rivet , diameter (mm) - Minimum breaking loed ER XXXXR, - 345 MPa in doubie shear (NI 1 250 1 997 . 3 174 4 621 6 265 8 222 12 985 18 835 33 570 52 800 I . ._ . _. -. a . Before upet ! 0278hilRO189T4 I b) After upset F-igre 1
23、 - Upset test Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3659 FaSe 9 5 Storing of docurtents For each lot, the manufacturei- shalt keep dccum
24、entahon stating 2s a minimum : * * 1 relationship between the rivet wire material lot and the rivet lot ; - a copy of documents concerning the rivet wire pnterial lot 2nd the test references ; - heat treatment documents for the rivet lot - documents concerning the rivet lot inspections and tests ; -
25、 the final inspection certificate. These documents ana all associated references shall be stored in an archive for at least three years, and zvailable for despatch to a client, Ut his reqest, 3hroughout this period. I 6 . Certificate of conformity The rivet manufacturer shall supply to the user, no
26、Inter than the delivery of the product, a final inspection certificate to confirm that the product .conforms with all the requirements of this specification. -* ?here applicable, actual test results shall be quoted. .- , Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
