1、ASD STANDARD NORME ASD ASD NORM prEN 6128 Edition P 2 February 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: See foreword for superseded version Descr
2、iptors: ENGLISH VERSION Aerospace series Blind bolt, 100 flush head, high strength Srie arospatiale Boulon aveugle tte fraise 100 haute rsistance Luft- und Raumfahrt Blindniet 100 Senkkopf, hochfest This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (AeroSpace
3、 and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical con
4、tent shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committ
5、ee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved f
6、or publication 28 February 2006 Comments should be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reprodu
7、ction or networking permitted without license from IHS-,-,-Page 2 prEN 6128:2006Foreword Due to a communication problem between the sponsor/responsible project team and ASD-STAN there was a confusion regarding the edition numbering of the recent version of this standard. In order to solve the situat
8、ion the ASD-STAN Board agreed to publish this version as Edition P2 and it is superseding the P1 version of prEN6128. Contents Page 1 Scope.3 2 Normative references3 3 Requirements.3 3.1 Configuration, dimensions and tolerances3 3.2 Grip range and weight3 3.3 Material, finish and lubrication.3 4 Des
9、ignation. 10 5 Marking 11 6 Technical specification . 11 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 6128:2006 1 Scope This standard s
10、pecifies the configuration, dimension, tolerances and mass of a stainless steel blind bolt with 100 flush head for aerospace application. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited
11、at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition o
12、f the publication referred to applies (including amendments). EN 2424, Aerospace series Marking of aerospace products EN 4473, Aerospace series Aluminium pigmented coatings Technical specification 1)AS 5272, Lubricant, solid film, heat cured, corrosion inhibiting procurement specification 2)AMS 5687
13、, Nickel alloy, corrosion and heat-resistant, wire 74Ni-15,5Cr-8,0Fe annealed 2)AMS 5690, Steel, corrosion and heat resistant, wire 17Cr-12Ni-2,5Mo (SAE 30316) solution heat treated 2)AMS 5737, Steel, corrosion and heat-resistant, bars, wire, forgings, and tubing 15Cr-25,5Ni-1,2Mo-2,1Ti-0,006B-0,30V
14、 consumable electrode melted 1650 F (899 C) solution and precipitation heat treated 2)AMS-QQ-P-35, Passivation treatments for corrosion-resistant steel 2)MIL-PRF-46010, Lubricant, solid film, heat cured, corrosion inhibiting 3)MIL-L-87132, Lubricant, cetyl alcohol, 1-hexadecanol, application to fast
15、eners 3)NASM 8975, Fastener, blind, high strength, installation formed corrosion resistant steel, heat resistant steel and titanium General specification for 3)DOD-L-85645, Lubricant, dry film, molecular bonded 3)3 Requirements 3.1 Configuration, dimensions and tolerances The configuration, dimensio
16、ns, tolerances, static and dynamic values shall conform to Figures 1 and 2 and Tables 1 and 2. 3.2 Grip range and weight See Tables 3 and 4. 3.3 Material, finish and lubrication See Tables 5 and 6. 1) Published as ASD Prestandard at the date of publication of this standard2) Published by: Society of
17、 Automotive Engineers (SAE), 400 Commonwealth drive, Warrendale, PA 15096-0001, USA 3) Published by: Department of Defense (DOD), the Pentagon, Washington, D.C. 20301 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo r
18、eproduction or networking permitted without license from IHS-,-,-Page 4 prEN 6128:20063)Marking see clause 5 R GRIPSleeveLocking CollarShifting Anvil2)Serrated Pin 100 1,5 ZKLBPDAWHCQN1)Detail of serrated pin geometry: XJ 1J2See Detail AD1D2EFGC1 C2Detail AJ1) The sleeve shall not rotating. 2) Diame
19、ter of serrated pin head shall not exceed “ D” max. 3) Fasteners are supplied with shifting anvil of manufacturers option. The shifting anvil is not part of the installed fastener Figure 1 Configuration Dimensions Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by
20、IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 6128:2006 Grip SP21)1) Blind side head may be installed on 7 max slope; 5 max slope for diameter code 10 and 12. Figure 2 Typical installation Table 1 Dimensions and tolerances
21、 Dimensions in mm (inch) A B C D J N Q D1 D2 W H P a P2Theor. max. Diameter code Ref. Ref. max. 0,025 ( .001) 0,127( .005) 0,25( .010) 0,13( .005) max. max. Gage dia. Gage height max. min. 05 8,48 (.334) 1,88 (.074) 0,28 (.011) 4,14 (.163) 9,53 (.375) 3,99 (.157) 1,70 (.067) 3,05(.120)2,16(.085)7,19
22、3 7,188 (.2832) (.2830) 0,523 0,434 (.0206) (.0171) 7,62(.300)5,66(.223)06 9,83 (.387) 2,08 (.082) 0,33 (.013) 5,03 (.198) 9,53 (.375) 4,45 (.175) 2,21 (.087) 3,81(.150)2,79(.110)8,311 8,306 (.3272) (.3270) 0,617 0,521 (.0243) (.0205) 8,13(.320)6,86(.27) 08 12,90 (.508) 2,74 (.108) 0,43 (.017) 6,58
23、(.259) 9,53 (.375) 4,62 (.182) 2,79 (.110) 4,83(.190)3,66(.144)10,973 10,968 (.4320) (.4318) 0,787 0,686 (.0310) (.0270) 9,40(.370)8,89(.35) 10 16,13 (.635) 3,56 (.140) 0,51 (.020) 7,90 (.311) 13,846 13,840 (.5451) (.5449) 0,932 0,826 (.0367) (.0325) 8,89(.350)9,47(.373)12 19,38 (.763) 4,27 (.168) 0
24、,58 (.023) 9,47 (.373) 16,718 16,713 (.6582) (.6580) 1,087 0,965 (.0428) (.0380) 10,29(.405)11,38(.448)continued Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license fr
25、om IHS-,-,-Page 6 prEN 6128:2006Table 1 Dimensions and tolerances (concluded) R S Z J1J2X E C1C2F G Hole limits Diameter code max. Ref. min. 0,76 ( .030) 0,76( .030) max. min. Ref. 0,05( .002) 5 5 min. max. 05 0,25 (.010) 5,89 (.232) 21,44 (.844) 15,14 (.596) 14,91(.587) 2,54(.100)0,13(.005)3,30(.13
26、0)0,81 (.032) 45 30 4,17 (.164) 4,24(.167)06 0,38 (.015) 7,42 (.292) 22,23 (.875) 15,62 (.615) 15,37(.605) 3,30(.130)0,13(.005)3,30(.130)0,81 (.032) 45 30 5,06 (.199) 5,13(.202)08 0,51 (.020) 9,17 (.361) 25,40 (1.000) 18,42 (.725) 16,97(.668) 3,81(.150)0,13(.005)3,30(.130)0,81 (.032) 45 30 6,60 (.26
27、0) 6,68(.263)10 0,64 (.025) 8,10 (.319) 30,68 (1.208) 7,93 (.312) 8,00(.315)12 0,76 (.030) 9,25 (.364) 39,68 (1.562) 9,40 (.374) 9,58(.377)aThis length of D may be 0,051 mm (.002) undersize. Table 2 Static values Dimensions in kN (lbs) Installed strength Diameter code Single shear min. Tensile stren
28、gth min. Tensile preload min. Spindle retention min. 05 8,811 (1980) 5,117 (1150) 0,512 (115) 2,558 (575) 06 13,016 (2925) 7,520 (1690) 0,752 (169) 3,760 (845) 08 22,250 (5000) 12,905 (2900) 1,29 (290) 6,408 (1440) 10 32,040 (7200) 18,556 (4170) 1,856 (417) 9,256 (2080) 12 46,191 (10380) 26,566 (597
29、0) 2,657 (597) 13,260 (2980) Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Table 3 Grip range Dimensions in mm (inch) Diameter code Under lap Grip r
30、ange Over lap 05 06 08 10 12 L K L K L K L K L K Grip length code min. only 05 dia. min. 06 dia. to 08 dia. min. max. max. 05 dia. to 08 dia. Ref. max. Ref. max. Ref. max. Ref. max. Ref. max. 02 2,39 a(.094) 3,99 (.0157) 4,39 (.173) 8,53 (.336) 12,14(.478) 9,02 (.355) 13,23 (.521) 03 3,71 (.146) 3,5
31、6 b(.14) 3,96 (.156) 5,59 (.220) 5,99 (.236) 10,11(.398) 13,72(.540) 10,59(.417) 14,81 (.583) 12,17(.479) 16,38(.645) 04 5,31 (.209) 5,16 (.203) 5,56 (.219) 7,16 (.282) 7,57 (.298) 11,71(.461) 15,32(.603) 12,19(.48) 16,41 (.646) 13,74(.541) 17,96(.707) 12,85(.506) 18,87(.743) 13,92(.548) 20,83(.82)
32、05 6,88 (.271) 6,73 (.265) 7,14 (.281) 8,76 (.345) 9,17 (.361) 13,28(.523) 16,89(.665) 13,77(.542) 17,98 (.708) 15,34(.604) 19,56(.77) 14,43(.568) 20,45(.805) 15,49(.61) 22,43(.883) 06 8,48 (.334) 8,33 (.328) 8,74 (.344) 10,34(.407) 10,74 (.423) 14,88(.586) 18,49(.728) 15,37(.605) 19,58 (.771) 16,92
33、(.666) 21,13(.832) 16,03(.631) 22,05(.868) 17,09(.673) 24,00(.945) 07 10,06 (.396) 9,91 (.39) 10,31 (.406) 11,94(.470) 12,34 (.486) 16,46(.648) 20,07(.790) 16,94(.667) 21,16 (.833) 18,52(.729) 22,73(.895) 17,60(.693) 23,62(.930) 18,67(.735) 25,58(1.007) 08 11,66 (.459) 11,51 (.453) 11,91 (.469) 13,5
34、1(.532) 13,92 (.548) 18,03(.71) 21,64(.852) 18,52(.729) 22,73 (.895) 20,09(.791) 24,31(.957) 19,20(.756) 25,22(.993) 20,27(.798) 27,18(1.07) 09 13,23 (.521) 13,08 (.515) 13,49 (.531) 15,11(.595) 15,52 (.611) 19,61(.772) 23,22(.914) 20,09(.791) 24,31 (.957) 21,69(.854) 25,91(1.02) 20,78(.818) 26,80(1
35、.055) 21,84(.86) 28,78(1.133) 10 14,83 (.584) 14.68 (.578) 15,09 (.594) 16,69(.657) 17,09 (.673) 21,21(.835) 24,82(.977) 21,69(.854) 25,91 (1.020) 23,27(.916) 27,48(1.082) 22,38(.881) 28,40(1.118) 23,44(.923) 30,35(1.195) 11 16,41 (.646) 16,26 (.64) 16,66 (.656) 18,29(.720) 18,67 (.735) 22,81(.898)
36、26,42(1.040) 23,29(.917) 27,51 (1.083) 24,87(.979) 29,08(1.145) 23,95(.943) 29,97(1.180) 25,02(.985) 31,93(1.257) 12 18,01 (.709) 17,86 (.703) 18,26 (.719) 19,86(.782) 20,27 (.798) 24,38(.960) 27,99(1.102) 24,87(.979) 29,08 (1.145) 26,44(1.041) 30,66(1.207) 25,55(1.006) 31,57(1.243) 26,62(1.048) 33,
37、53(1.32) 13 19,58 (.771) 19,43 (.765) 19,84 (.781) 21,46(.845) 21,84 (.860) 25,98(1.023) 29,59(1.165) 26,47(1.042) 30,68 (1.208) 28,04(1.104) 32,26(1.270) 27,13(1.068) 33,15(1.305) 28,19(1.11) 35,13(1.383) 14 21,18 (.834) 21,03 (.828) 21,44 (.844) 23,04(.907) 23,44 (.923) 27,56(1.085) 31,17(1.227) 2
38、8,07(1.105) 32,28 (1.271) 29,62(1.166) 33,83(1.332) 28,73(1.131) 34,75(1.368) 29,79(1.173) 36,70(1.445) 15 22,76 (.896) 22,61 (.89) 23,01 (.906) 24,64(.970) 25,02 (.985) 29,16(1.148) 32,77(1.290) 29,67(1.168) 33,88 (1.334) 31,22(1.229) 35,43(1,395.)30,30(1.193) 36,32(1.430) 31,37(1.235) 38,28(1.507)
39、 16 23,36 (.959) 24,21 (.953) 24,61 (.969) 26,21(1.032) 26,619 (1.048) 30,74(1.210) 34,34(1.352) 31,24(1.230) 35,48 (1.397) 32,79(1.291) 37,03(1.458) 31,90(1.256) 37,92(1.493) 32,97(1.298) 39,88(1.57) Page 7prEN 6128:2006continued Copyright Association Europeene des Constructeurs de Materiel Aerospa
40、tial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 6128:2006Diameter code Under lap Grip range Over lap 05 06 08 10 12 L K L K L K L K L K Grip length code min. only 05 dia. min. 06 dia. to 08 dia. min. max. ma
41、x. 05 dia. to 08 dia. Ref. max. Ref. max. Ref. max. Ref. max. Ref. max. 17 25,81 (1.016) 26,19 (1.031) 27,81(1.095) 28,22 (1.111) 32,82(1.292) 37,06 (1.459) 34,37(1.353) 38,61(1.520) 33,48(1.318) 39,50(1.555) 34,54(1.36) 41,48(1.633) 18 27,38 (1.078) 27,79 (1.094) 29,39(1.157) 29,79 (1.173) 34,42(1.
42、355) 38,66 (1.522) 35,97(1.416) 40,21(1.583) 35,078(1.381) 41,10(1.618) 36,14(1.423) 43,05(1.695) 19 28,98 (1.141) 29,36 (1.156) 30,99(1.220) 31,39 (1.236) 35,99(1.417) 40,23 (1.584) 37,54(1.478) 41,78(1.645) 36,65(1.443) 42,67(1.680) 37,72(1.485) 44,63(1.757) 20 30,56 (1.203) 30,96 (1.219) 32,56(1.
43、282) 32,97 (1.298) 37,59(1.480) 41,83 (1.647) 39,14(1.541) 43,34(1.708) 38,25(1.506) 44,27(1.743) 39,32(1.548) 46,23(1.820) 21 32,13 (1.265) 32,54 (1.281) 34,16(1.345) 34,54 (1.360) 39,17(1.542) 43,41 (1.709) 40,72(1.603) 44,96(1.770) 42,11(1.658) 45,85(1.805) 40,89(1.61) 47,83(1.883) 22 33,73 (1.32
44、8) 34,14 (1.344) 35,74(1.407) 36,14 (1.423) 40,77(1.605) 45,01 (1.772) 42,32(1.666) 46,56(1.833) 42,42(1.670) 47,45(1.868) 42,49(1.673) 49,40(1.945) 23 35,31 (1.390) 35,71 (1.406) 37,34(1.470) 37,72 (1.485) 42,34(1.667) 46,58 (1.834) 43,89(1.728) 48,13(1.895) 43,00(1.693) 49,02(1.930) 44,07(1.735) 5
45、0,98(2.007) 24 36,91 (1.453) 37,31 (1.469) 38,91(1.532) 39,32 (1.548) 43,94(1.730) 48,18 (1.897) 45,49(1.791) 49,73(1.958) 44,60(1.756) 50,62(1.993) 45,67(1.798) 52,58(2.07) 25 38,48 (1.515) 38,89 (1.531) 40,51(1.595) 40,89 (1.610) 45,52(1.792) 49,76 (1.959) 47,07(1.853) 51,31(2.020) 46,18(1.818) 52
46、,20(2.055) 47,24(1.86) 54,18(2.133) 26 40,49 (1.594) 42,09(1.657) 47,78(1.881) 53,80(2.118) 48,84(1.923) 55,75(2.195) 27 42,06 (1.656) 43,69(1.720) 49,35(1.943) 55,37(2.180) 50,42(1.985) 57,33(2.257) 28 43,66 (1.719) 45,26(1.782) 50,95(2.006) 56,97(2.243) 52,02(2.048) 58,93(2.32) 29 45,24 (1.781) 46
47、,86(1.845) 53,59(2.11) 60,53(2.383) 30 46,84 (1.844) 48,44(1.907) 55,19(2.173) 62,10(2.445) 31 48,41 (1.906) 50,04(1.970) 56,77(2.235) 63,68(2.507) 32 50,01 (1.969) 51,61(2.032) 58,37(2.298) 65,28(2.57) aMinimum grip length for diameter code 05 is 2,39 (0.094) and for diameter code 06 is 3,05 (.120). b No underlap for diameter code 08. Dimensions in mm (inch) Table 3 Grip range (concluded) Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-
