1、- MIL-T-6 192C(USAE) SUPERSEDING MIL-T-6192B(ASG) 18 June 1954 20 June i967 MILITARY SPECIFICATION TRAINER, WEATHER CONDITION MAP 1. SCOPE 1.1 This specification covers one type of weather-condition map trainer. 2. APPLICABLE: DOCUMENTS 2.1 The following documents of the issue in effect on date of i
2、nvitation for bid or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS Federa 1 MM-L-736 NN-P-530 TT-V - 119 UU-P-268 PPP -B - 5 7 6 PPP-B-601 PPP-B-636 PPP-B - 640 PPP-C-843 Military MIL-P - 116 MIL-P-5425 MIL-L- 10547 STANDARDS Federal FED-STD-1
3、41 Mi li tary , MIL-STD-129 MIL-STD-130 MIL-STD-1186 -_ Lumber and Timber; Hardwood Plywood; Flat Panel Varnish, Spar, Phenolic-Resin Paper, Kraft, Untreated, Wrapping Box, Wood, Cleated, Veneer, Paper Overlaid Boxes, Wood, Cleated-Plywood Box, Fiberboard Boxes, Fiberboard, Corrugated, Triple-Wall C
4、ushioning Material, Cellulosic al. Preservation, Methods of Plastic, Sheet, Acrylic, Heat Resistant Liners, Case, and Sheet, Overwrap; Water-Vaporproof or Waterproof, Flexible Paint, Varnish, Lacquer, and Related Materials; Methods of Inspection, Sampling., and Testing Marking for Shipment and Stora
5、ge Identification Marking of U,S, Military Property Cushioning, Anchoring, Bracing, Blocking, and Water- proofing; with Appropriate Test Methods .I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-bL72C 67 7797706 037.5347 3 -_ MIL-T-6192C (USAF
6、 ) (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained frm procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 Pre roduction. This specification makes provisions for
7、 preproduction test&* 3.2 Materials . 3.2.1 Plywood. 3 or 5 ply, A-B grade conforming to NN-P-530. All plywood used in the construction of the trainer shall be 3.2.2 Lumber. oak hardwood conforming to MM-L-736. All lumber used in the construction of the trainer shall be 3.2.3 Plastic plates. trainer
8、 shall conform to MIL-P-5425, finish A. be acrylic base. Ali plastic plates used in the construction of the Paints and inks used shall 3.3 Design and construction. units, each unit conforming to the dimensions shown on Figure 1. The trainer shall consist of three separate 3.3.1 Plywood base. be moun
9、ted on the upper surface of the plywood base conforming to the dimen- sions shown on Figre 1. four rubber bumpersr A large-scale section of a suitable weather map shall The lower side of the plywood base shall contain 3.3.2 Posts and rails. be firmly fastened to the base. free fit with the upright p
10、lastic plates. Four vertical wooden posts and two wooden rails shall The posts and rails shall be slotted for a 3.3.3 Plastic plates. Eight transparent plastic plates depicting weather conditions shall be provided and located as shown on Figure 1. Each plate shall be 19 by 10 inches and 5/32 2 1/32
11、inch thick. ground smooth and the corners neatly rounded. The edges shall be 3.3.4 Cover. fabricated of 3/+-inch plywood conforming to NN-P-530 with al1 corner joints reinforced by 1-2 inch by i-& inch aluminum angle material, depth dimensions of this cover shaU be such that, when placed over the un
12、it, a snug fit shall exist between the cover and the vertical wooden corner posts of the trainer. plastic plates allowing sufficient space for the padded spacer inserts. Each demonstrational unit shall be provided with a cover The width and The height shall be such as to clear the top edge of the .
13、2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ 1. MIL-T-bL72C 69 7799906 0375350 T r- MIL-T-G (WAF ) FIGURE 1. WEATIFER CONDITION DEMONSTRATOR Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-,.-
14、NIL-T-bI72C b7 m 7797706 0375351 I m I 3.3.4.1 Connection, shall be provided to prevent separation during shipment or s torage. A rigid connection between the cover and the plywood base 3.34.2 Spacer inserts. permanently fixed to the interior surface along both sides of the cover top. The slots shal
15、l be felt padded and spaced to engage the top edges of the plastic plates when the cover is installed in the correct position over the unit. Two 1-inch by 1-inch slotted wooden strips shall be 3.4 Performance characteristics, The trainer shall be capable of representing typical conditions of cloud f
16、ormation, winds and precipitation over an area 800 by 1,000 miles, and an altitude of 25,000 feet. Each unit shall illustrate the following types of weather conditions: (a) Warm-front occlusion (b) Cold-front occlusion (c) open-sector cyclone 3.5 Color and finish 3.5.1 Wooden surfaces. All wooden su
17、rfaces shall be sanded and finished with three coats of varnish conforming to TT-V-119. 3.6 Identification of product. Equipment, assemblies and parts shall be marked for identification in accordance with MIL-STD-130. The nomenclature and stock number to be included on the equipment nameplate shall
18、be as follows: Trainer, Weather Condition Map Stock NO 6910-264-5884 3.6.1 Transparent plastic plates. Each plastic plate shall be identified by a Roman Numeral followed by an Arabic Numeral. The plates shall be marked in accordance with the following outline: (a) Open-sector cyclone, 1-1 through 1-
19、8 (b) Cold-front occlusion, 11-1 through 11-8 (c) Warm-front occlusion, 111-1 through 111-8 3.7 Government-loaned property. When the contract or purchase order provides (see 6.2), the Government will loan the following to the contractor for use in fabricating the trainer: Item Description Quantity I
20、tem No. Stock No. Part No. 1 6910-264-5884 MIL-T-6192 Weather Condi tion 1 Map Trainer 3.8 Workmanship. The trainer shall be fabricated-and furnished in a thoroughly workmanlike manner such that the item is suitable for the purpose intended, 4 Provided by IHSNot for ResaleNo reproduction or networki
21、ng permitted without license from IHS-,-,-MIL-T-6192C 69 m 9999906 0375352 3 m - MIL-T- 61 92C (USAP ) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection re
22、quirements as specified herein. the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and service conform to prescribed require- ment s. E
23、xcept as otherwise specified, The Government reserves the right to perform any 4.2 Classification of tests. be classified as follows: The inspection and testing of the trainer shall (a) Preproduction tests . see 4.3 (b) Acceptance tests see 4,4 4.3 Preproduction testing. 4,3.1 Preproduction test sam
24、ple. The preproduction test sample shall consist of one model representative of the production equipment (see 6.2). 4,3.2 Preproduction tests. described in 4.5. The preproduction tests shall consist of all tests 4,4 Acceptance tests. 4.4.1 described in 4.5. The acceptance tests shall consist of indi
25、vidual tests, Individual tests. Each trainer shall be subjected to the tests 4,5 Test methods. 4,5.1 Examination of products. compliance with 3.2, 3,4, and 3.8. Weather conditions depicted shall be. inspected for conformance with sample weather maps. The trainer shall be inspected to determine 4.5.2
26、 Adhesion test. with method 6301 of FED-STD-141. FED-STD-141 shall not be required, The specimens shall be immersed for six hours in distilled water in lieu of the specified 24 hours. painted surface results from this test, the items shall not be acceptable. Adhesion of paint and ink shall be tested
27、 in accordance The two scratches specified in method 6301 of If damage to the 4.6 Rejection and retest, When a trainer fails to meet the specification, the trainers still on hand or later produced shall not be accepted until the extent and cause of failure have been determined and appropriately corr
28、ected. The contractor shall explain to the Government representative the cause of failure and the action taken to preclude recurrence. After correction, all the tests shall be repeated. ., Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-bL92C
29、69 W 7999906 0375353 5 W MIL-T-.c (USAF ) 5. PFIEPARATION FOR DELIVERY 5.1 Preservation and packaging. or C as specified (see 6.2) . Preservation and packaging shall be level A 5.1.1 Level A. Each trainer, securely fastened in a cover, shall be preserved and packaged in accordance with method III of
30、 MIL-P-u. wrapped with paper conforming to -P-268, and adequately cushioned in accordance with PPP-C-843. Each unit shall be 5.1.2 Level C, from corrosion and physical damage during shipment to the first receiving activity for immediate use. 5.2 Packing. Each trainer shall be packaged to afford adeq
31、uate protection Packing shall be level A, By or C as specified (see 6.2). 5.2.1. Level A. Each trainer, as specified in 5.1.1, shall be packed in ext.erior-type shipping containers conforming to PPP-B-576, PPP-B-601 and Class 2, Grade A of PPP-B-&O and appendices thereto. As far as practical, exteri
32、or containers shall be of uniform shape and size, of minimum cube and tare consistent with the protection required and shall contain identical quantities. Containers shall be closed and strapped in accordance with the applicable container specification or appendix thereto. provided with case liners
33、conforming to MIL-L-10547. Containers shall be 5.2.2 Level B. Each trainer, as specified in 5.1.1, shall be packed in domestic-type exterior containers conforming to PPP-B-576, PPP-B-601, or PPP-B-636. with the protection required. As far as practicable, exterior containers shall be uniform in shape
34、 and size and shall contain identical quantities. Containers shall be closed and strapped in accordance with the applicable container specification or appendix thereto. Ekterior containers shall be of minimum cube and tare consistent 5.2.3 Level C. carrier shall be packed in exterior-type shipping c
35、ontainers in a manner that will assure safe transportation at the lowest rate to the point of delivery. Containers shall meet Consolidated Freight Classification Rules or regulations of other common carriers, as applicable to the mode of transportation. Packages which require overpacking for accepta
36、nce by the 5.3 Physical protection. Cushioning, blocking, and bolting, as required, shall be in accordance with MIL-sTD-ll86, excepting waterproofing shall be waived for domestic shipments. the plastic plate sections within each unit cover. shall be waived when Level C packaging is specified, or whe
37、n the drop tests of MIL-P-ll6 are applicable. 5.4 Marking. purchase order (see 6.2), interior and exterior containers shall be marked in accordance with the requirements of MILSTD-129. nomenclature and stock number shall be as follows: Interior cushioning shall be provided between Drop tests of MIL-
38、STD-1186 In addition to any special marking required by the contract or The shipment marking Trainer, Weather Condition Map St ock NO 6910-264-584 6 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T- 6 1 92C (USAF ) 6. NOTES 6.1 Intended use, T
39、he weather condition map trainer is intended for use in classroom instruction to teach personnel in the recognition of cloud formations. 6.2 Ordering data. Procurement documents should specify the following: (A) Title, number and date of this specification. (B) Whether a preproduction sample is requ
40、ired (see 3.1). (C) When Government-loaned property will be made available (see 3.7). (D) (E) Whether special marking is required (see 5.4). Selection of applicable levels of packaging and packing (see 5.1 and 5.2). 6.3 Asterisks. Asterisks are not used in this revision to identify changes with respect to the previous issue, due to the extensiveness of the changes. Custodian: Air Force - 70 Preparing Activity: Air Force - 70 Project No 6910-0056 *US. GOVERNMENT PRMTMG OFFICE:- 1967-301 -509/30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
