1、ASSE/IAPMO/ANSI Series 10000-2010(R2015) ASSE Board Approved: July 2015 ANSI Approved: September 2015 An American National Standard Professional Qualifications Standard for Green Plumbing Systems Installers ASSE InternationalASSE Series 10000-2010(R2015) Professional Qualifications Standard i Issued
2、 September 2015 Copyright Information iii Foreword v Professional Qualifications Standards Committee vi Series 10000 Working Group . vii Standard #10001 1 1-1.1 Reference and Industry Standards and Codes 1 1-1.2 Abbreviations and Standards Development Organizations .4 Professional Qualifications St
3、andard for Green Plumbing Systems Installers Standard #10100 5 Green Plumbing Systems Installers 10-1.1 Scope 5 10-1.2 Purpose 5 10-1.3 Limitations . 5 10-1.4 Reference and Industry Standards and Codes . 5 10-2.1 General Knowledge 5 10-2.2 Product Knowledge .5 10-2.3 Product Installation Knowledge 6
4、 10-2.4 System Knowledge . 6 10-2.5 Documenting and Recording . 6 10-3.1 Terminology . 6 10-3.2 Certification and Recertification of Installers . 6 Appendix A 9 Vocabulary and Definitions TAble oF ConTenTSii ASSE Series 10000-2010(R2015) Professional Qualifications Standard Issued: September 2015ASS
5、E Series 10000-2010(R2015) Professional Qualifications Standard iii Issued: September 2015 Professional Qualifications Standard for Green Plumbing Systems Installers ASSE International Mokena, Illinois Copyright 2015, 2010 All rights reserved. CoPYRIGHT InFoRMATIon Neither this standard, nor any por
6、tion thereof, may be reproduced without the written consent of ASSE International. Organizations wishing to adopt or list any ASSE Standard should print the ASSE Standard Number on the cover page first and in equal or larger type to that of the adopting or listing organization. iv ASSE Series 10000-
7、2010(R2015) Professional Qualifications Standard Issued: September 2015ASSE Series 10000-2010(R2015) Professional Qualifications Standard v Issued: September 2015 Professional Qualifications Standard for Green Plumbing Systems Installers FoRe WoRd This foreword shall not be considered a part of the
8、standard; however, it is offered to provide background information. This is the ASSE/IAPMO/ANSI Series 10000, Professional Qualifications Standard for Green Plumbing Systems Installers. ASSE International and the International Association of Plumbing and Mechanical Officials (IAPMO) serve as co-secr
9、etariats for the standard. ASSE International is dedicated to the preservation of public health and safety through the use of proper plumbing and piping practices and approved materials. Its mission is to, in the spirit of its motto “Prevention Rather Than Cure,” continually improve the performance,
10、 reliability and safety of plumbing systems. The International Association of Plumbing and Mechanical Officials (IAPMO) has been protecting the publics health and safety and supporting sustainability and emerging technology for more than eighty years by working in concert with government and industr
11、y to implement comprehensive plumbing and mechanical systems around the world. With the escalation of green building and the rapid emergence of sustainable technologies and construction practices, ASSE and IAPMO recognized the need to establish a level of competency necessary for the installation an
12、d inspection of sustainable plumbing and mechanical systems and products to protect public health, safety and the environment. As such, the Series 10000 Working Group was established to develop this Professional Qualification Standard for Green Plumbing Systems. The Series 10000 standard institutes
13、a minimum level of practical experience and the demonstration of knowledge of the requirements referenced in the 2010 IAPMO Green Plumbing and Mechanical Code Supplement in order for an individual to demonstrate the required level of competency. This voluntary, consensus standard was promulgated in
14、accordance with procedures developed by the American National Standards Institute (ANSI).vi ASSE Series 10000-2010(R2015) Professional Qualifications Standard Issued: September 2015 d onald Summers Jr., ChairpersonUA Local 562St. Louis, MO Kenneth borski UA Local 68 JACHouston, TX Philip CampbellUni
15、ted AssociationAnnapolis, MD laurence T . ColemanUA Local 597Mokena, IL d ana ColomboNational Inspection T esting & Certification (NITC)Metairie, LA Robert l. CrossUA Local 68 JACHouston, TX e dward l yczkoCleveland Clinic - RetireeCleveland, OH Matthew Marciniak (non-voting)International Associatio
16、n of Plumbing and Mechanical Officials (IAPMO)Milwaukee, WI d ouglas MarianUA Local 78Los Angeles, CA barry Pines, CPdC & R PlumbingShelby T ownship, MI Richard J. ProspalProspal Consulting Services Inc.Brunswick, OH d aniel RademacherPlumbing Code & Design ConsultingButte, MT Philip RoachMazzettiPo
17、rtland, OR Kenneth SchneiderSprinkler Fitters UA Local 268 JATCSt Louis, MO Jason ShankUA Local 55Cleveland, OH Jaime ValdiviaNational Inspection T esting & Certification (NITC)Los Angeles, CA Marianne Waickman (non-voting) ASSE InternationalMokena, IL Professional Qualifications Standard for Green
18、Plumbing Systems Installers 2015 ASSe PQ STAndARdS C oMMITTeeASSE Series 10000-2010(R2015) Professional Qualifications Standard vii Issued: September 2015 Scott Hamilton, ChairmanPlumbers Local 75 Education FundMilwaukee, Wisconsin Robert benazziJaros Baum & BollesNew York, New York Phil CampbellUni
19、ted Association Training Depart.Las Vegas, Nevada Mike Hadley United Service Training Corp (USTC)Pompano Beach, Florida Professional Qualifications Standard for Green Plumbing Systems Installers Ron George Ron George Design & Consulting ServicesMonroe, Michigan Steve SilberUA Local 342 JATCConcord,
20、California d ave ViolaIAPMOMokena, Illinois Marianne C. WaickmanASSE Westlake, Ohio 2015 ASSe SeRIeS 10000 W oRKInG GR oUPviii ASSE Series 10000-2010(R2015) Professional Qualifications Standard Issued: September 2015ASSE Series 10000-2010(R2015) Professional Qualifications Standard 1 Issued: Septemb
21、er2015 01-1.1 Reference and Industry Standards and Codes The following list of reference and industry standards and codes is part of the requirements of ASSE Series 10000 Standard. 01-1.1.1 ACCA Manual D, 7th Edition, Residential Duct Systems, Section 702.4.4 01-1.1.2 ACCA Manual J, 7th Edition, Res
22、idential Load Calculation, Table 702.6.1 01-1.1.3 AHAM RAC-1-87-2003, Room Air Conditioners, Table 703.8.1(4) 01-1.1.4 ARCSA/ASPE, Rainwater Catchment Design and Installation Standard, Section 505.1 01-1.1.5 ARI 210/240-2006, Performance Rating of Unitary Air Conditioning and Air-Source Heat Pump Eq
23、uipment, Table 703.8.1(1), Table 703.8.1(2), Table 702.9 01-1.1.6 ARI 310/380-2004 (CSA-C744-04), Standard for Packaged Terminal Air Conditioners and Heat Pumps, Table 703.8.1(4) 01-1.1.7 ARI (AHRI) 325-1998, Grand Water-Source Heat Pumps, Table 702.9 01-1.1.8 ARI (AHRI) 340/360-2007, Commercial and
24、 Industrial Unitary Air-Conditioning and Heat Pump Equipment, Table 703.8.1(1), Table 703.8.1(2) 01-1.1.9 ARI (AHRI) 365-2009, Commercial and Industrial Unitary Air-Conditioning Condensing Unit, Table 703.8.1(1) 01-1.1.10 ARI (AHRI) 390-2003, Performance Rating of Single Package Vertical Air-Conditi
25、oners and Heat Pumps, Table 703.8.1(4) 01-1.1.11 ARI (AHRI) 400-2001, Liquid to Liquid Heat Exchangers with addendum 2, Table 703.8.1(8) 01-1.1.12 ARI (AHRI) 460-2000 2005, Remote Mechanical Draft Air Cooled Refrigerant Condensers, Table 703.8.1(7) 01-1.1.13 ARI (AHRI) 550/590-2003, Performance Rati
26、ng of Water Chilling Packages Using the Vapor Compression Cycle, Section 704.3.1.2, Table 703.8.1(3) ASSE SEriES 10000 StAndArd #10001 01-1.1.14 ARI (AHRI) 560-2000, Absorption Water Chilling and Water Heating Packages, Table 703.8.1(3) 01-1.1.15 ARI (AHRI) 1160-2008, Performance Rating of Heat Pump
27、 Pool Heaters, Table 603.4.2 01-1.1.16 ASHRAE 52.1-1992, Gravimetric and Dust Spot Procedures for Testing Air Cleaning Devices Used in General Ventilation for Removing Particulate Matter, Section 803.1.1 01-1.1.17 ASHRAE 52.2-2007, Method of Testing General Ventilation Air Cleaning Devices for Remov
28、al Efficiency by Particle Size, Chapter 2, 803.1.1 01-1.1.18 ASHRAE 55-2004, Thermal Environmental Conditions for Human Occupancy, Section 807.1 01-1.1.19 ASHRAE 62.1-2007, Ventilation for Acceptable Indoor Air Quality, Sections 703.5.1, 703.5.2.1, 703.5.2.3 01-1.1.20 ASHRAE 62.2-2007, Ventilation a
29、nd Acceptable Indoor Air Quality in Low-Rise Residential Buildings, Section 805.1.3 01-1.1.21 ASHRAE 90.1-2007 (2008 Supplement), Energy Standard for Buildings Except Low-Rise Residential Buildings (Includes Addenda a, b, c, g, h, i, j, k, l, m, n, p, q, s, t, u, w, y, ad, and aw), Chapter 6, Chapte
30、r 7 01-1.1.22 ASHRAE 90.2-2007, Energy Efficient Design of Low- Rise Residential Buildings, Chapter 6, Chapter 7 01-1.1.23 ASHRAE 136-1993, A Method of Determining Air Change Rates in Detached Dwellings, Section 805.1.3.1.3 01-1.1.24 ASHRAE 146-2006, Method of Testing and Rating Pool Heaters, Table
31、603.4.2 01-1.1.25 ASHRAE GRP-158-1979, Cooling and Heating Load Calculation Manual, Table 702.6.1 01-1.1.26 ASHRAE/ACCA 183-2007, Peak Cooling and Heating Load Calculations in Buildings Except Low Rise Residential Buildings, Section 703.4.2 01-1.1.27 ASME A112.18.1/CSA B125.1-2005, Plumbing Supply F
32、ittings, Sections 402.4.1, 402.4.2.1, 402.5 01-1.1.28 ASME A112.19.2/CSA B45.1-2008, Ceramic Plumbing Fixtures, Sections 402.2.1, 402.2.2, 402.3 References & T erminology2 ASSE Series 10000-2010(R2015) Professional Qualifications Standard Issued: September 2015 01-1.1.29 ASME A112.19.3/CSA, Stainles
33、s Steel Plumbing Fixtures, Section 402.3.1 01-1.1.30 ASME A112.19.14-2006, Six-Liter Water Closets Equipped With a Dual Flushing Device, Section 402.2.1 01-1.1.31 ASME A112.19.19-2006, Vitreous China Nonwater Urinals, Section 402.3.1 01-1.1.32 ASSE 1016-2005, Automatic Compensating Valves for Indivi
34、dual Showers and Tub/Shower Combinations, Section 402.5.4 01-1.1.33 ASSE-5000-2009, Cross-Connection Control Professional Qualifications Standard 01-1.1.34 ASTM A53/A53M-06a, Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless 01-1.1.35 ASTM A312/A312M-06,
35、Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes 01-1.1.36 ASTM A778-01, Standard Specification for Welded, Unannealed Austenitic Stainless Steel Tubular Products 01-1.1.37 ASTM B32-04, Standard Specification for Solder Metal 01-1.1.38 ASTM B42-02
36、e1, Standard Specification for Seamless Copper Pipe, Standard Sizes 01-1.1.39 ASTM B75-02, Standard Specification for Seamless Copper Tube 01-1.1.40 ASTM B43-98 (2004), Standard Specification for Seamless Red Brass Pipe, Standard Sizes 01-1.1.41 ASTM B75-02, Standard Specification for Seamless Coppe
37、r Tube 01-1.1.42 ASTM B88-03, Standard Specification for Seamless Copper Water Tube 01-1.1.43 ASTM B251M-97(2003), Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube Metric 01-1.1.44 ASTM B251-02e1, Standard Specification for General Requirements for Wr
38、ought Seamless Copper and Copper- Alloy Tube 01-1.1.45 ASTM B302-02, Standard Specification for Threadless Copper Pipe, Standard Sizes 01-1.1.46 ASTM B447-07, Standard Specification for Welded Copper Tube 01-1.1.47 ASTM B813-00e1, Standard Specification for Liquid and Paste Fluxes for Soldering of C
39、opper and Copper Alloy Tube 01-1.1.48 ASTM B828-02, Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings 01-1.1.49 ASTM C518-2004, Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus, Table
40、 703.8.2(1), Table 703.8.2(2) 01-1.1.50 ASTM D2683-2004, Standard Specification for Socket- Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing, Section 705.1.2 01-1.1.51 ASTM D2846/D2846M-06, Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plas
41、tic Hot- and Cold-Water Distribution Systems 01-1.1.52 ASTM D3035-2008, Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter, Section 705.1.2 01-1.1.53 ASTM D3261-2003, Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings fo
42、r Polyethylene (PE) Plastic Pipe and Tubing, Section 705.1.2 01-1.1.54 ASTM D3350-2008, Standard Specification for Polyethylene Plastics Pipe and Fittings Materials, Section 705.1.2 01-1.1.55 ASTM E96-2005, Standard Test Methods for Water Vapor Transmission of Materials, Section 702.4.1 01-1.1.56 AS
43、TM F1055-2006, Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing, Section 705.1.2 01-1.1.57 ASTM F437-06, Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 01-1
44、1.58 ASTM F438-04, Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 01-1.1.59 ASTM F439-06, Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 01-1.1.60 ASTM F441/F441M-02, Standard
45、Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 01-1.1.61 ASTM F442/F442M-99(2005), Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) 01-1.1.62 ASTM F876-06, Standard Specification for Crosslinked Polyethylene (PEX) T
46、ubing 01-1.1.63 ASTM F877-07, Standard Specification for Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems 01-1.1.64 AWS A5.8/A5.8M, Specification for Filler Metals for Brazing and Braze Welding 01-1.1.65 AWS A5.31 Type FB3-A or FB3-C, Specification for Fluxes for Brazi
47、ng and Braze WeldingASSE Series 10000-2010(R2015) Professional Qualifications Standard 3 Issued: September2015 01-1.1.66 CAN/CSA C448-2002 (R2007), Design and Installation of Earth Energy Systems, Section 705.1.1 01-1.1.67 CFR 10, 430, App N, DOE Uniform Test Method for Measuring the Energy Consumpt
48、ion of Furnaces, Table 603.4.2, Table 703.8.1(5), Table 703.8.1(6) 01-1.1.68 CFR 10, 431, DOE Energy Efficiency Program for Certain Commercial and Industrial Equipment, Table 703.8.1(6) 01-1.1.69 CSA B137.1-2005, Thermoplastic Pressure Piping Compendium, Polyethylene (PE) Pipe, Section 705.1.2 01-1.
49、1.70 CSA B137.5-05, Crosslinked polyethylene (PEX) Tubing Systems for Pressure Applications 01-1.1.71 CSA B137.6-05, Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing, and Fittings for Hot- and Cold-Water Distribution Systems 01-1.1.72 CSA Z21.10.3-2004, Gas Water Heaters, Volume III, Storage Water Heaters With Input Ratings Above 75 000 BTU per Hour, circulating and Instantaneous, Table 703.8.1(5) 01-1.1.73 CSA/AM CSA/Z83.8-2006, Gas Unit Heaters and Gas-Fired Duct Furnaces, Table 703.8.1(5) 01-1.1.74 CTI ATC-105-2000, Acceptance Test Code for Water Cooling Towers, Table 703.8.1(7) 0
