ANSI API SPEC 5CRA-2010 Specification for Corrosion-resistant Alloy Seamless Tubes for Use as Casing Tubing and Coupling Stock (FIRST EDITION Effective August 1 2010 ERTA August 20.pdf
《ANSI API SPEC 5CRA-2010 Specification for Corrosion-resistant Alloy Seamless Tubes for Use as Casing Tubing and Coupling Stock (FIRST EDITION Effective August 1 2010 ERTA August 20.pdf》由会员分享,可在线阅读,更多相关《ANSI API SPEC 5CRA-2010 Specification for Corrosion-resistant Alloy Seamless Tubes for Use as Casing Tubing and Coupling Stock (FIRST EDITION Effective August 1 2010 ERTA August 20.pdf(100页珍藏版)》请在麦多课文档分享上搜索。
1、Specification for Corrosion-resistant Alloy Seamless Tubes for Use as Casing, Tubing, and Coupling StockANSI/API SPECIFICATION 5CRAFIRST EDITION, FEBRUARY 2010EFFECTIVE DATE: AUGUST 1, 2010ERRATA , AUGUST 2011REAFFIRMED, APRIL 2015ISO 13680:2010 (Identical), Petroleum and natural gas industriesCorro
2、sion-resistant alloy seamless tubes for use as casing, tubing, and coupling stockTechnical delivery conditionsSpecial NotesAPI publications necessarily address problems of a general nature. With respect to particular circumstances, local,state, and federal laws and regulations should be reviewed.Nei
3、ther API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make anywarranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of theinformation contained herein, or assume any liability or responsibility for a
4、ny use, or the results of such use, of anyinformation or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors,consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.Classified areas may vary depend
5、ing on the location, conditions, equipment, and substances involved in any givensituation. Users of this specification should consult with the appropriate authorities having jurisdiction.Users of this specification should not rely exclusively on the information contained in this document. Sound busi
6、ness,scientific, engineering, and safety judgment should be used in employing the information contained herein. API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure theaccuracy and reliability of the data contained in them; however, the Inst
7、itute makes no representation, warranty, orguarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities having jurisdiction with which this publication mayconflict.API pub
8、lications are published to facilitate the broad availability of proven, sound engineering and operatingpractices. These publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where these publications should be utilized. The formulation and publica
9、tion of API publicationsis not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible for complying with all the applicable requirements of that standard
10、. API does not represent,warrant, or guarantee that such products do in fact conform to the applicable API standard.All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or
11、otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2010 American Petroleum InstituteAPI ForewordNothing contained in any API publication is to be construed as granting any right, by implica
12、tion or otherwise, for themanufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anythingcontained in the publication be construed as insuring anyone against liability for infringement of letters patent.This document was produced under API standardiz
13、ation procedures that ensure appropriate notification andparticipation in the developmental process and is designated as an API standard. Questions concerning theinterpretation of the content of this publication or comments and questions concerning the procedures under whichthis publication was deve
14、loped should be directed in writing to the Director of Standards, American PetroleumInstitute, 1220 L Street, N.W., Washington, D.C. 20005. Requests for permission to reproduce or translate all or anypart of the material published herein should also be addressed to the director.Shall: As used in a s
15、tandard, “shall” denotes a minimum requirement in order to conform to the specification.Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in orderto conform to the specification. Generally, API standards are reviewed and revised, reaffirmed, o
16、r withdrawn at least every five years. A one-timeextension of up to two years may be added to this review cycle. Status of the publication can be ascertained from theAPI Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is publishedannually by API, 1220 L St
17、reet, N.W., Washington, D.C. 20005.Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW,Washington, D.C. 20005, standardsapi.org.iiiiii Contents Page API Foreword ii Foreword . v Introduction vi 1 Scope 1 2 Conformance 2 2.1 Dual normative refer
18、ences . 2 2.2 Units of measurement . 2 3 Normative references 2 4 Terms, abbreviated terms, symbols and definitions . 4 4.1 Terms and definitions . 4 4.2 Symbols 6 4.3 Abbreviated terms . 7 5 Information to be supplied by the purchaser . 8 6 Manufacturing process . 9 6.1 Manufacturing of corrosion-r
19、esistant alloys 9 6.2 Product manufacturing process 9 6.3 Pipe end sizing 9 6.4 Straightening 9 6.5 Processes requiring validation 10 6.6 Traceability . 10 7 Material requirements . 10 7.1 Chemical composition 10 7.2 Tensile properties 10 7.3 Hardness properties 10 7.4 Charpy V-notch test properties
20、 General requirements . 11 7.5 Charpy V-notch Absorbed energy requirements for coupling stock All grades . 12 7.6 Charpy V-notch Absorbed energy requirements for pipe All grades . 12 7.7 Flattening requirements 13 7.8 Corrosion properties . 14 7.9 Microstructure properties . 14 7.10 Surface conditio
21、n 14 7.11 Defects 14 7.12 Hydrostatic test . 15 8 Dimensions, masses and tolerances 15 8.1 Outside diameter, wall thickness and mass . 15 8.2 Length . 15 8.3 Tolerances 16 8.4 Product ends 16 9 Inspection and testing 16 9.1 Test equipment 16 9.2 Type and frequency of tests . 16 9.3 Testing of chemic
22、al composition. 17 9.4 Testing of mechanical characteristics 17 9.5 Tensile test . 18 9.6 Hardness test . 18 9.7 Impact or flattening test 19 9.8 Microstructural examination 21 iv 9.9 Dimensional testing 22 9.10 Drift test . 22 9.11 Length 23 9.12 Straightness 23 9.13 Mass determination 23 9.14 Hydr
23、ostatic test . 23 9.15 Visual inspection 24 9.16 Non-destructive examination 24 10 Surface treatment . 29 10.1 Group 1 29 10.2 Groups 2, 3 and 4 29 11 Marking 30 11.1 General . 30 11.2 Marking on the product 30 11.3 Date of manufacture . 31 12 Surface protection Group 1 . 31 13 Documents 32 13.1 Ele
24、ctronic media . 32 13.2 Retention of records . 32 14 Handling, packaging and storage . 33 14.1 General . 33 14.2 Handling . 33 14.3 Packaging 33 14.4 Storage . 33 Annex A (normative) Tables in SI units . 34 Annex B (normative) Figures in SI (USC) Units 54 Annex C (normative) Tables in USC units . 59
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIAPISPEC5CRA2010SPECIFICATIONFORCORROSIONRESISTANTALLOYSEAMLESSTUBESFORUSEASCASINGTUBINGANDCOUPLINGSTOCKFIRSTEDITIONEFFECTIVEAUGUST12010ERTAAUGUST20PDF

链接地址:http://www.mydoc123.com/p-431047.html