ANSI ASME B16.47 INTERPRETATIONS-1995 Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60.pdf

上传人:confusegate185 文档编号:431730 上传时间:2018-11-11 格式:PDF 页数:3 大小:151.67KB
下载 相关 举报
ANSI ASME B16.47 INTERPRETATIONS-1995 Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60.pdf_第1页
第1页 / 共3页
ANSI ASME B16.47 INTERPRETATIONS-1995 Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60.pdf_第2页
第2页 / 共3页
ANSI ASME B16.47 INTERPRETATIONS-1995 Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、- STD-ASME BLbm47 INT-ENGL m 0759b70 0579222 5b7 m INTERPRETATIONS TO ASME B16.47 (These interpretations are not part of ASME B16.47-1996 and are included for information only. These interpretations apply to the 1988 and earlier editions and the requirements cited may be different in this Edition. T

2、herefore, some replies may not be valid in regard to this Edition.) INTRODUCTION As a service to persons who use the B16 standards, the B16 Committee renders interpretations of the requirements upon request. The procedure for requesting an interpretation is described in the following paragraphs. The

3、 interpretations include all replies which have been approved by the B16 Main Committee in response to inquiries concerning interpretation of this Standard. An interpretation applies either to the Edition and Addenda in effect on the date of issuance of the interpretation or the Edition and Addenda

4、stated in the interpretation. Subsequent revisions to this Standard may supersede the interpretation. PROCEDURE FOR REQUESTING INTERPRETATIONS On request, the B16 Committee will render an interpretation of any requirement of this Standard. Interpretations can only be rendered in response to a writte

5、n request, which should be addressed to: Secretary, B14 Main Committee The American Society of Mechanical Engineers United Engineering Center 345 East 47th Street New York, NY 10017 The request for interpretation should be clear and unambiguous. It is further recommended that the (a) Subject. Cite t

6、he applicable paragraph number(s) and/or give a concise description of the subject. (6) Question. Phrase the question as a request for an interpretation of a specific requirement suitable for general understanding and use, not as a request for an approval of a proprietary design or situation. The in

7、quirer may also include any plans or drawings which are necessary to explain the question; however, they should not contain proprietary names or information. Requests which are not in this format may be rewritten in this format prior to being answered, which may inadvertently change the original int

8、ent of the request. ASME procedures provide for reconsideration of an interpretation when or if additional information is available which the inquire believes might affect the interpretation. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME committee or subcommittee.

9、ASME does not “approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device, or activity. inquirer submit his request using the following format: 61 816.47 Interpretations No. 1 1-1 INTERPRETATIONS NO. 1 Replies to Technical Inquiries Issued from July 24, 1990 Through Decembe

10、r 31, 1995 Interpretation: 1-1 Subject: Hub Tapers Date Issued: October 3, 1995 File: B 16-95-07 Question (1): Does B16.47-1990 require dual taper hubs as shown in Figs. 1 and 2? Reply (1): No. See para. 6.4 and Note (3) to Figs. 1 and 2. Question (2): Does B16.47-1990 specify where dimension “A” is

11、 measured on a single tapered hub as allowed in Note (3)? Reply (2): No. B16.47 does not address where to measure dimension “A” 63 AMERICAN NATIONAL STANDARDS FOR PIPING, PIPE FLANGES, FITTINGS, AND VALVES The ASME Publications Catalog shows a complete list of all the Standards published by the Society. For a complimentary catalog, or the latest information about our publications, call 7-800-THE-ASME (7-800-843-2763).

展开阅读全文
相关资源
  • ANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdfANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdf
  • ANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdfANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdf
  • ANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdfANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdf
  • ANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdfANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdf
  • ANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdfANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf
  • ANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdfANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdf
  • ANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdfANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdf
  • ANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdfANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdf
  • ANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdfANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdf
  • ANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdfANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ANSI

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1