ANSI ASTM D2671-2013 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use《电气用热收缩管道系统的试验方法》.pdf
《ANSI ASTM D2671-2013 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use《电气用热收缩管道系统的试验方法》.pdf》由会员分享,可在线阅读,更多相关《ANSI ASTM D2671-2013 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use《电气用热收缩管道系统的试验方法》.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2671 13Standard Test Methods forHeat-Shrinkable Tubing for Electrical Use1This standard is issued under the fixed designation D2671; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number
2、in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 These test methods cover the testing of heat-shrinkable
3、tubing used for electrical insulation. Materials used includepoly(vinyl chloride), polyolefins, fluorocarbon polymers, sili-cone rubber, and other plastic or elastomeric compounds.1.2 The procedures appear in the following sections:Procedure SectionsASTM MethodReferenceAdhesive Peel Strength 98 104B
4、rittleness Temperature 40 D746Color 55 and 56 D1535Color Stability 57 62 D1535Conditioning 7 D618Copper Stability 93Corrosion Testing 8995Dielectric Breakdown 20 25 D149Dimensions 8 13 D876Flammability 68 72 D876Fluid Resistance 6367Fungus Resistance 104 108Heat Resistance 4954Heat Shock 2630Low-Tem
5、perature Properties 3643Restricted Shrinkage 1419Selection of Test Specimens 6Secant Modulus 81 84 D882Storage Life 3135Specific Gravity 73 and 74 D792Stress Modulus 85 88 D412Tensile Strength and Ultimate Elongation 44 48 D412Thermal Endurance 96 and 97Volume Resistivity 75 78 D257Water Absorption
6、79 and 80 D570Melting Point 104 108 D34181.3 This is a fire-test-response standard.1.4 The values stated in inch-pound units are to be regardedas standard, except for temperature, which shall be expressedin degrees Celsius. The values given in parentheses aremathematical conversions to SI units that
7、 are provided forinformation only and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the app
8、lica-bility of regulatory limitations prior to use. For specific hazardstatements, see Sections 5 and 68.2.NOTE 1These test methods are similar, but not identical to, those inIEC 606842 (see also Note 9).2. Referenced Documents2.1 ASTM Standards:2D149 Test Method for Dielectric Breakdown Voltage and
9、Dielectric Strength of Solid Electrical Insulating Materialsat Commercial Power FrequenciesD257 Test Methods for DC Resistance or Conductance ofInsulating MaterialsD412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD570 Test Method for Water Absorption of PlasticsD618 Practi
10、ce for Conditioning Plastics for TestingD746 Test Method for Brittleness Temperature of Plasticsand Elastomers by ImpactD792 Test Methods for Density and Specific Gravity (Rela-tive Density) of Plastics by DisplacementD876 Test Methods for Nonrigid Vinyl Chloride PolymerTubing Used for Electrical In
11、sulationD882 Test Method for Tensile Properties of Thin PlasticSheetingD1535 Practice for Specifying Color by the Munsell SystemD1711 Terminology Relating to Electrical InsulationD3418 Test Method for Transition Temperatures and En-thalpies of Fusion and Crystallization of Polymers byDifferential Sc
12、anning CalorimetryE176 Terminology of Fire Standards2.2 Other Documents:MIL-STD 104 Limits for Electrical Insulation Color31These test methods are under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and are the direct responsibility ofSubcommittee D09.07 on
13、Electrical Insulating Materials.Current edition approved Nov. 1, 2013. Published December 2013. Originallyapproved in 1967. Last previous edition approved in 2009 as D2671 09. DOI:10.1520/D2671-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service a
14、t serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.*A Summary of Changes section app
15、ears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Princi
16、ples for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1IEC Publication 216 Guide for the Determination of Ther-mal Endurance Properties of Electrical Insulating Materi-als4IEC Publication 6068
17、4 Specification for Flexible InsulatingSleeving4ISO 846 PlasticsEvaluation of the Action of Microorgan-isms43. Terminology3.1 Definitions:3.1.1 For definitions pertaining to electrical insulation, referto Terminology D1711.3.1.2 For definitions pertaining to fire standards, refer toTerminology E176.
18、3.1.3 heat-shrinkable tubing, ntubing that will reduce indiameter from an expanded size to a predetermined size by theapplication of heat.3.2 Definitions of Terms Specific to This Standard:3.2.1 brittleness temperature, nthe temperature at which50 % of the specimens fail when the specified number ar
19、etested using the apparatus and conditions specified.3.2.2 concentricity, nthe ratio expressed in percent of theminimum wall thickness to the maximum wall thickness.3.2.3 longitudinal change, nthe change in length, eitherpositive or negative, that occurs when the tubing is allowed tofreely recover a
20、t the recommended recovery temperature,expressed as a percentage of the as supplied or expandedlength.3.2.4 low-temperature flexibility, nthe resistance to crack-ing of tubing when wrapped around prescribed mandrels atspecified temperatures.3.2.5 restricted shrinkage, nshrinkage of the tubing at apr
21、escribed temperature over a specially designed mandrelwhose smallest diameter is greater than the fully shrunk sizeand whose largest diameter is less than the expanded size of thetubing.3.2.6 storage-life, heat-shrinkable tubing, nthe length oftime that the tubing will retain its specified expanded
22、andrecovered dimensions under storage at a specified temperature.4. Significance and Use4.1 These test methods include most of the important testsused to characterize heat-shrinkable tubing. They are intendedprimarily for, but not limited to, extruded heat-shrinkabletubing.4.2 It is acceptable to us
23、e variations in these test methods oralternate contemporary methods of measurement to determinethe values for the properties in this standard provided suchmethods ensure quality levels and measurement accuracy equalto or better than those prescribed herein. It is the responsibilityof the organizatio
24、ns using alternate test methods to be able todemonstrate this condition. In cases of dispute, the methodsspecified herein shall be used.NOTE 2Provision for alternate methods is necessary because of (1) thedesire to simplify procedures for specific applications without altering theresult, and (2) the
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIASTMD26712013STANDARDTESTMETHODSFORHEATSHRINKABLETUBINGFORELECTRICALUSE 电气 收缩 管道 系统 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-432297.html