1、Designation: F985 18 An American National StandardStandard Specification forPilot Platform1This standard is issued under the fixed designation F985; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision. A numbe
2、r in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides design and constructiondetails for pilot platforms.1.2 The values stated in SI units are to be regarded asstanda
3、rd. No other units of measurement are included in thisstandard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendati
4、ons issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2B221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars, Rods, Wire, Profiles, and Tubes3. Ordering Information3.1 Pilot platforms shall be ordered by this ASTM
5、designa-tion and year of issue.3.2 Paint finish (if other than standard).4. Materials and Methods4.1 Platforms shall be welded-aluminum construction inaccordance with Specification B221, Alloy 5086.4.2 Decking shall be serrated-aluminum grating.4.3 Canopy shall be of vinyl-nylon construction with se
6、wnseams and metallic grommets.4.4 Canopy tie-downs shall be 4-mm nylon line.4.5 Paint finish, if required, shall be in accordance withcustomer specifications.5. Dimensions, Weight, and Permissible Variations5.1 Dimensions as indicated in Figs. 1-7.5.2 The approximate unit weight is 1250 N.5.3 The co
7、nstruction tolerance is 4 mm, except bolt holelocation 1 mm.6. Workmanship, Finish, and Appearance6.1 Shelters shall be free of weld splatter, sharp edges, andburrs injurious to personnel.7. Keywords7.1 pilot platform1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Mar
8、ine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved April 1, 2018. Published April 2018. Originallyapproved in 1986. Last previous edition approved in 2012 as F985 00 (2012).DOI: 10.1520/F0985-18.2For referenced ASTM standar
9、ds, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1
10、9428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Tec
11、hnical Barriers to Trade (TBT) Committee.1FIG. 1 Pilot PlatformF985 182FIG. 2 Front ViewF985 183FIG. 3 Side ViewF985 184FIG. 4 Top ViewF985 185FIG. 5 Floor DetailsF985 186FIG. 6 Section Connecting PinsF985 187ASTM International takes no position respecting the validity of any patent rights asserted
12、in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the
13、responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive ca
14、reful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internatio
15、nal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 7 Ship AttachmentF985 188
