ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf

上传人:brainfellow396 文档编号:433828 上传时间:2018-11-11 格式:PDF 页数:26 大小:195.60KB
下载 相关 举报
ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf_第1页
第1页 / 共26页
ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf_第2页
第2页 / 共26页
ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf_第3页
第3页 / 共26页
ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf_第4页
第4页 / 共26页
ANSI AWS C3.9M C3.9-2009 Specification for Resistance Brazing (First Edition).pdf_第5页
第5页 / 共26页
点击查看更多>>
资源描述

1、AWS C3.9M/C3.9:2009An American National StandardSpecification forResistance Brazing550 N.W. LeJeune Road, Miami, FL 33126AWS C3.9M/C3.9:2009An American National StandardApproved by theAmerican National Standards InstituteJuly 30, 2008Specification forResistance Brazing1st EditionPrepared by theAmeri

2、can Welding Society (AWS) C3 Committee on Brazing and SolderingUnder the Direction of theAWS Technical Activities CommitteeApproved by theAWS Board of DirectorsAbstractThis specification provides the minimum fabrication, equipment, material, and process procedure requirements, as well asdiscontinuit

3、y limits for the resistance brazing of steels, copper, copper alloys, heat- and corrosion-resistant alloys, andother materials that can be adequately resistance brazed (the resistance brazing of aluminum alloys is addressed in AWSC3.7M/C3.7, Specification for Aluminum Brazing). This specification pr

4、ovides criteria for classifying resistance brazedjoints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptabilityin each class. This specification defines acceptable resistance brazing equipment, materials, and procedures, as well asthe requ

5、ired inspection for each class of joint.iiAWS C3.9M/C3.9:2009International Standard Book Number: 978-0-87171-510-4American Welding Society550 N.W. LeJeune Road, Miami, FL 33126 2008 by American Welding SocietyAll rights reservedPrinted in the United States of AmericaPhotocopy Rights. No portion of t

6、his standard may be reproduced, stored in a retrieval system, or transmitted in anyform, including mechanical, photocopying, recording, or otherwise, without the prior written permission of the copyrightowner.Authorization to photocopy items for internal, personal, or educational classroom use only

7、or the internal, personal, oreducational classroom use only of specific clients is granted by the American Welding Society provided that the appropriatefee is paid to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, tel: (978) 750-8400; Internet:.iiiAWS C3.9M/C3.9:2009Statement

8、 on the Use of American Welding Society StandardsAll standards (codes, specifications, recommended practices, methods, classifications, and guides) of the AmericanWelding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of theAmerican National Sta

9、ndards Institute (ANSI). When AWS American National Standards are either incorporated in, ormade part of, documents that are included in federal or state laws and regulations, or the regulations of other govern-mental bodies, their provisions carry the full legal authority of the statute. In such ca

10、ses, any changes in those AWSstandards must be approved by the governmental body having statutory jurisdiction before they can become a part ofthose laws and regulations. In all cases, these standards carry the full legal authority of the contract or other documentthat invokes the AWS standards. Whe

11、re this contractual relationship exists, changes in or deviations from requirementsof an AWS standard must be by agreement between the contracting parties.AWS American National Standards are developed through a consensus standards development process that bringstogether volunteers representing varie

12、d viewpoints and interests to achieve consensus. While the AWS administers theprocess and establishes rules to promote fairness in the development of consensus, it does not independently test, evalu-ate, or verify the accuracy of any information or the soundness of any judgments contained in its sta

13、ndards.AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whetherspecial, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or relianceon this standard. AWS also makes no guarantee or war

14、ranty as to the accuracy or completeness of any informationpublished herein.In issuing and making this standard available, AWS is neither undertaking to render professional or other services for oron behalf of any person or entity, nor is AWS undertaking to perform any duty owed by any person or ent

15、ity to someoneelse. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek theadvice of a competent professional in determining the exercise of reasonable care in any given circumstances. It isassumed that the use of this standard and its provisions

16、are entrusted to appropriately qualified and competent personnel.This standard may be superseded by the issuance of new editions. Users should ensure that they have the latest edition.Publication of this standard does not authorize infringement of any patent or trade name. Users of this standard acc

17、eptany and all liabilities for infringement of any patent or trade name items. AWS disclaims liability for the infringement ofany patent or product trade name resulting from the use of this standard.Finally, the AWS does not monitor, police, or enforce compliance with this standard, nor does it have

18、 the power to do so.On occasion, text, tables, or figures are printed incorrectly, constituting errata. Such errata, when discovered, are postedon the AWS web page (www.aws.org).Official interpretations of any of the technical requirements of this standard may only be obtained by sending a request,i

19、n writing, to the appropriate technical committee. Such requests should be addressed to the American Welding Society,Attention: Managing Director, Technical Services Division, 550 N.W. LeJeune Road, Miami, FL 33126 (see Annex B).With regard to technical inquiries made concerning AWS standards, oral

20、opinions on AWS standards may be rendered.These opinions are offered solely as a convenience to users of this standard, and they do not constitute professionaladvice. Such opinions represent only the personal opinions of the particular individuals giving them. These individualsdo not speak on behalf

21、 of AWS, nor do these oral opinions constitute official or unofficial opinions or interpretations ofAWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation.This standard is subject to revision at any time by the AWS C3 Committee on Brazing a

22、nd Soldering. It must be reviewedevery five years, and if not revised, it must be either reaffirmed or withdrawn. Comments (recommendations, additions, ordeletions) and any pertinent data that may be of use in improving this standard are required and should be addressed toAWS Headquarters. Such comm

23、ents will receive careful consideration by the AWS C3 Committee on Brazing and Solder-ing and the author of the comments will be informed of the Committees response to the comments. Guests are invited toattend all meetings of the AWS C3 Committee on Brazing and Soldering to express their comments ve

24、rbally. Proceduresfor appeal of an adverse decision concerning all such comments are provided in the Rules of Operation of the TechnicalActivities Committee. A copy of these Rules can be obtained from the American Welding Society, 550 N.W. LeJeuneRoad, Miami, FL 33126.This page is intentionally blan

25、k.ivAWS C3.9M/C3.9:2009vAWS C3.9M/C3.9:2009PersonnelAWS C3 Committee on Brazing and SolderingP. T. Vianco, Chair Sandia National LaboratoriesR. W. Smith, Vice Chair Materials Resources InternationalS. N. Borrero, Secretary American Welding SocietyG. L. Alexy The Prince therefore, a series of six ind

26、ependent specifications on brazing have been written, all in the same format. These areAWS C3.4M/C3.4, Specification for Torch Brazing; AWS C3.5M/C3.5, Specification for Induction Brazing; AWSC3.6M/C3.6, Specification for Furnace Brazing; AWS C3.7M/C3.7, Specification for Aluminum Brazing; AWSC3.8M/

27、C3.8, Specification for the Ultrasonic Examination of Brazed Joints; and the present document, AWSC3.9M/C3.9, Specification for Resistance Brazing.The decision to subdivide the technology in this way was based on a survey of production brazing applications con-ducted by the AWS C3 Committee on Brazi

28、ng and Soldering. The survey demonstrated that these six specificationswould cover the vast majority of brazing performed today.After the completion of the fourth brazing specification, it was determined that a document providing specific criteriaand requirements for the application of ultrasonic te

29、sting to brazed joints was needed. Therefore, AWS C3.8M/C3.8,Specification for the Ultrasonic Examination of Brazed Joints, was written to complement this series.AWS C3.9M/C3.9, Specification for Resistance Brazing, has been added to this group of diverse standards on brazingprocesses because resist

30、ance brazing is an additional commercial brazing method used in many industries. The specificsfor this method are detailed in the same manner as the other five independent brazing specifications.Comments and suggestions for the improvement of this standard are welcome. They should be sent to the Sec

31、retary,AWS C3 Committee on Brazing and Soldering, American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126.This page is intentionally blank.viiiAWS C3.9M/C3.9:2009ixAWS C3.9M/C3.9:2009Table of ContentsPage No.PersonnelvForeword vii1. Scope.12. Normative References .13. Terms and Definitions.

32、24. Classification of Brazed Joints.24.1 Method of Classification.24.2 Class A Joints24.3 Class B Joints24.4 Class C Joints24.5 No Class Specified35. Process Requirements.35.1 Process Description.35.2 Equipment.35.3 Materials .45.4 Procedure Requirements .45.5 Qualification .55.6 Safety and Health56

33、. Quality Assurance Provisions 56.1 Responsibility for Inspection 56.2 Requirements for Compliance 56.3 Sequence of Inspection and Manufacturing Operations .56.4 Required Inspection of Brazed Joints .66.5 Acceptance Criteria.76.6 Process Completion 8Annex A (Informative)Informative References .9Anne

34、x B (Informative)Guidelines for the Preparation of Technical Inquiries.11List of AWS Documents on Brazing and Soldering 13This page is intentionally blank.xAWS C3.9M/C3.9:2009AWS C3.9M/C3.9:200911. ScopeThis specification presents the minimum fabrication andquality requirements for the resistance br

35、azing of materi-als such as steels, stainless steels, copper, copper alloys,and heat- or corrosion-resistant materials as well as othermaterials that can be adequately resistance brazed.The purpose of this specification is to standardize resis-tance brazing process requirements and control brazejoin

36、t quality for all applications requiring brazed joints ofassured quality. This document establishes the minimumrequirements for processes and products with a minimumof explanatory information so that sources of ambiguityare minimized. It assigns responsibility for the ultimatequality of the brazed p

37、roduct to a single organization andpermits that organization to modify requirements ifappropriate to the application. It requires proper docu-mentation of any such modifications.Procedures for the protection of the safety and health ofthose performing resistance brazing and related opera-tions are o

38、f great importance. However, safety and healthissues and concerns are beyond the scope of this standardand therefore are not fully addressed herein. Safety andhealth information is available from other sources,including, but not limited to, ANSI Z49.1, Safety inWelding, Cutting, and Allied Processes

39、.This standard makes use of both the International Systemof Units (SI) and U.S. Customary Units. The latterare shown within brackets , or in appropriate columnsin tables and figures. The measurements may not beexact equivalents; therefore, each system shall be usedindependently.2. Normative Referenc

40、esThe standards listed below contain provisions that,through reference in this text, constitute mandatory pro-visions of this AWS standard. For undated references,the latest edition of the referenced standard shall apply.For dated references, subsequent amendments to, or revi-sions of, any of these

41、publications do not apply.American Welding Society (AWS) standards:1AWS A2.4, Symbols for Welding, Brazing, and Non-destructive Examination;AWS A3.0, Standard Welding Terms and Definitions,Including Terms for Adhesive Bonding, Brazing, Solder-ing, Thermal Cutting, and Thermal Spraying;AWS A5.8/A5.8M

42、, Specification for Filler Metals forBrazing and Braze Welding;AWS A5.31/A5.31M, Specification for Fluxes forBraze and Braze Welding;AWS B2.2, Standard for Brazing Procedure and Per-formance Qualification;AWS C3.3, Recommended Practices for the Design,Manufacture, and Examination of Critical Brazed

43、Com-ponents; andAWS C3.8M/C3.8, Specification for the UltrasonicExamination of Brazed Joints.American Society for Quality (ASQ) standard:2ASQ Z1.4, Sampling Procedures and Tables forInspection by Attributes.SAE International/Aerospace Materials Division (AMD)standards:3SAE AMS 2403, Plating, General

44、 Purpose;SAE AMS 2424, Plating, Nickel, Low Stressed Deposit;1AWS standards are published by the American WeldingSociety, 550 N.W. LeJeune Road, Miami, FL 33126.2ASQ standards are published by the American Society forQuality (ASQ), 600 North Plankinton Avenue, Milwaukee, WI53203-3005.3SAE Internatio

45、nal standards are published by the Society ofAutomotive Engineers, 400 Commonwealth Drive, Warrendale,PA 15096-0001.Specification for Resistance BrazingAWS C3.9M/C3.9:20092SAE AMS 2451/1, Plating, Brush, Nickel GeneralPurpose; andSAE AMS 2750, Pyrometry.ASTM International standards:4ASTM E 1742, Sta

46、ndard Practice for RadiographicExamination; andASTM E 1417, Practice for Liquid PenetrantExamination.National Conference of Standards Laboratories (NCSL)standard:5NCSL Z540-1, General Requirements for CalibrationLaboratories and Measuring and Test Equipment.3. Terms and DefinitionsAWS A3.0, Standard

47、 Welding Terms and Definitions,Including Terms for Adhesive Bonding, Brazing, Solder-ing, Thermal Cutting, and Thermal Spraying, providesthe basis for terminology used herein.For the purposes of this document, the following termsand definitions apply:braze joint. The total area, as defined by the en

48、gineeringdrawing, of the faying surfaces to be joined by braz-ing and the fillets that form at the edges of that area.braze joint proper. The total area, as defined by theengineering drawing, of the faying surfaces to bejoined by brazing, excluding any fillets that form atthe edges of that area.braz

49、ing procedure specification (BPS). A documentspecifying the required brazing variables for a spe-cific application.brazing symbol. The symbol on the engineering draw-ing designating the location, class, and configurationof the brazed joint. Such symbols shall be in accor-dance with AWS A2.4, Standard Symbols for Weld-ing, Brazing, and Nondestructive Examination.joint dimensions. The joint length is the greater of thetwo dimensions of the joint parallel to the faying sur-faces. The joint width is the lesser of these two dimen-4ASTM International standards are published by ASTM Inter-nati

展开阅读全文
相关资源
  • ANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdfANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdf
  • ANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdfANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdf
  • ANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdfANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdf
  • ANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdfANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdf
  • ANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdfANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf
  • ANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdfANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdf
  • ANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdfANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdf
  • ANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdfANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdf
  • ANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdfANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdf
  • ANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdfANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ANSI

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1