1、 INCITS/ISO/IEC 19757-4:2006/COR 1:20082010 (ISO/IEC 19757-4/Cor1:2008, IDT) Corrigendum Reaffirmed as INCITS/ISO/IEC 19757-4:2006/COR 1:2008 R2015INCITS/ISO/IEC 19757-4:2006/COR 1:20082010 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this
2、file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretari
3、at accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure
4、that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. D
5、ate of ANSI Approval: 7/15/2010 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2010 by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Org
6、anization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior wr
7、itten permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1101 K Street NW, Suite 610, Washington DC 20005. Printed in the United States of America ii ITIC 2010 All rights reserved ICS 35.240.30 Ref. No. ISO/IEC 19757-4:2006/Cor.1:2008(E) ISO/IEC 2008 All rights r
8、eserved Published in Switzerland INTERNATIONAL STANDARD ISO/IEC 19757-4:2006 TECHNICAL CORRIGENDUM 1 Published 2008-09-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATIONINTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION LECTROTECHNIQUE INTERNATIONALEInfo
9、rmation technology Document Schema Definition Languages (DSDL) Part 4: Namespace-based Validation Dispatching Language (NVDL) TECHNICAL CORRIGENDUM 1 Technologies de linformation Langages de dfinition de schma de documents (DSDL) Partie 4: Langage de diffusion de validation despace de nom orient (NV
10、DL) RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO/IEC 19757-4:2006 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 34, Document description and processing languages. Page 6, 6.2, the definition of the attribute “nameList“ Add “+“ after “xsd:
11、NCName“ in “list xsd:NCName “. Page 9, 6.3, the definition of the attribute “nameList“. Add “+“ after “xsd:NCName“ in “list xsd:NCName “. ISO/IEC 19757-4:2006/Cor.1:2008(E) 2 ISO/IEC 2008 All rights reservedPage 9, Clause 6.3 Replace message = element message text “. Page 30, Annex A, thirteenth lin
12、e from the bottom of the page Replace with ISO/IEC 19757-4:2006/Cor.1:2008(E) 4 ISO/IEC 2008 All rights reservedPage 31, Annex B, the definition of the attribute “nameList“ in the middle of this page Replace with Page 33, Annex B, the third line on this page Replace with Page 33, Annex B, the sixth
13、line from the bottom of this page Replace the two occurrences of “. Page 35, C.2, the ninth line from the bottom of this page Replace with Page 38, C.2, the thirteenth line on this page Replace with ISO/IEC 19757-4:2006/Cor.1:2008(E) ISO/IEC 2008 All rights reserved 5Page 39, C.2, the twenty-sixth line on this page Replace the two occurrences of “. Page 46, D.3.1, the twenty-fifth line from the bottom of this page Insert the following line between the line “ and the line “: Page 47, D.3.1, the first line on this page Insert the following line between the line “ and the line “:
