1、INTERNATIONAL STANDARD ISO/IEC 9983 Second edition 1995-09-l 5 Information technology - Designation of unrecorded flexible disk cartridges Technologies de /information - Dksignation des car-touches 2 disquettes vierges Reference number ISO/IEC 9983:1995(E) Adopted by INCITS (InterNational Committee
2、for Information Technology Standards) as an American National Standard.Date of ANSI Approval: 5/12/98Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2002 by Information Technology Industry Council (ITI).All rights reserved.These materials are
3、 subject to copyright claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council(ITI). Not for resale. No part of this publication may be reproduced in any form,
4、 including an electronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the United States of AmericaISO/IEC 9983:1995 (E) 1 scope 2 Normative references 3 Specificat
5、ion of the identifier 4 Information on packages 5 Information on the flexible disk cartridge 6 Allocation of type numbers 7 Type numbers of already published International Standards Annex A - Main characteristics of FDCs available Page 1 1 2 2 2 2 2 4 OISO/IEC 1995 All rights reserved. Unless otherw
6、ise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher ISOllEC Copyright Office l Case Postale 56 l CH-1211 Geneve 20 l Switzerland Printed
7、in Switzerland ii 0 ISO/IEC ISO/IEC 9983:1995 (E) Foreword IS0 (the International Organization for Standardization) and IEC (the International Electrical Commission) form the specialized system for world-wide standardization. National Bodies that are members of IS0 or IEC participate in the developm
8、ent of International Standards through technical committees established by the respective organization to deal with particular fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with IS0 and IEC, also take part in the work. In the field of inf
9、ormation technology, IS0 and IEC have established a joint technical committee ISOLIEC JTC 1. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75% of the national
10、 bodies casting a vote. International Standard ISO/IEC 9983 was prepared by the European Computer Manufacturers Association (as Standard ECMA-124) and was adopted, under a special “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approva
11、l by national bodies of IS0 and IEC. This second edition cancels and replaces the first edition (ISOLIEC 9983:1989), which has been technically revised. Annex A of this International Standard is for information only. . . . 111 ISOiIEC 9983:1995 (E) 0 ISO/IEC Introduction Since the beginning of their
12、 activity in the field of standardization of flexible disk cartridges IS0 has issued standards for such cartridges of three different sizes, viz. 200 mm (8 in), 130 mm (5,25 in) and 90 mm (35 in). It can be foreseen that in not too distant a future further smaller sizes may be considered. Some of th
13、ese cartridges, whilst having the same size, do not have the same magnetic characteristics and, therefore, should be used only with the physical recording density and the number of tracks for which they have been designed. In practice, however, they are offered commercially to end users in packages
14、bearing indications (e.g. lD, DD, I-ID, etc.) which are clear for those skilled in the art but quite obscure to the average buyer. As a consequence it was necessary to arrive at a consensus on type designation to be used nationally and internationally. Investigations have shown that manufacturers of
15、 flexible disk cartridges are willing to print the proposed designation in addition to the presently used identifiers which would remain during a transition period. The proposed designation is explicit in that it specifies not only a type, but also minimum information indicating the main parameters
16、as well. In the interests of users it is desirable that the scheme described be implemented now and as a whole. However, as the suppliers of flexible disk cartridges, drives and systems have already developed their own designations for cartridges, and their own procedures for marking packages, it wo
17、uld be expensive to implement the whole scheme immediately. It is expected that suppliers will introduce the specified marking of cartridges and packages, and the references in manuals, as soon as the re- ordering of cases, packaging and printing makes this economically possible. iv INTERNATIONAL ST
18、ANDARD 0 ISOAK ISO/IEC 9983:1995 (E) Information technology - Designation of unrecorded flexible disk cartridges 1 Scope This International Standard specifies an identifier to appear on each flexible disk cartridge (FIX) and the minimum information to appear on packages of unrecorded flexible disk c
19、artridges. The information according to this International Standard shall appear on cartridges and on packages of unrecorded flexible disk cartridges available to end users. Drives for FDCs should bear the indication of the Type(s) of FDC they can handle. Manuals for drives and systems should also i
20、nclude this information. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to
21、 agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid standards. IS0 5654-1:1984, Information processing - Data interchange on
22、200 mm (8 in)flexible disk cartridges using two-frequency recording at 13 262ftprad, Z,9 tpmm (48 tpi), on one side - Part 1: Dimensional, physical and magnetic characteristics. IS0 6596-l: 1985, Information processing - Data interchange on 130 mm (5,25 in) flexible disk cartridges using hvo-frequen
23、cy recording at 7 598frprad, I,9 tpmm (48 tpi), on one side - Part I: Dimensional, physical and magnetic characteristics. IS0 7065-1:1985, Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using modified frequency modulation recording at 13 262ftprad, Z,9 tpmm (48 t
24、pi), on both sides - Part 1: Dimensional, physical and magnetic characteristics. ISOIIEC 7487-l 11993, Information technology - Data interchange on 130 mm (5,25 in)Jlexible disk cartridges using modified frequency modulation recording at 7 958 ftprad, 1,9 tpmm (48 tpi), on both sides - IS0 Type 202
25、- Part 1: Dimensional, physical and magnetic characteristics. IS0 8378-1:1986, Information processing - Data interchange on 130 mm (5,25 in) flexible disk cartridges using modified frequency modulation recording at 7 958ftprad, 3,8 tpmm (96 tpi), on both sides - Part I: Dimensional, physical and mag
26、netic characteristics. IS0 8630-1:1987, Information processing - Data interchange on 130 mm (5,25 in) flexible disk cartridges using modified frequency modulation recording at 13 262ftprad, on 80 tracks on each side - Part 1: Dimensional, physical and magnetic characteristics. IS0 8860-11987, Inform
27、ation processing - Data interchange on 90 mm (3,s in) flexible disk cartridges using modified frequency modulation recording at 7 958frprad on 80 tracks on each side - Part I: Dimensional, physical and magnetic characteristics. ISOiIEC 9529-11989, Information processing systems - Data interchange on
28、 90 mm (3,5 in) flexible disk cartridges using modified frequency modulation recording at 15 916ftprad, on 80 tracks on each side - Part I: Dimensional, physical and magnetic characteristics. ISOIIEC 10994 11992, Znformation technology - Data interchange on 90 mm flexible disk cartridges using modif
29、ied frequency modulation recording at 31 831 ftprad on 80 tracks on each side - IS0 Type 303. ISOIIEC 13422: 1994, Znformation technology - Data interchange on 90 mm Flexible Disk Cartridges 10 Mbyte capacity using sector servo tracking - IS0 type 304. ISOIIEC 14169:1995, Information technology - 90
30、 mm flexible disk cartridges - 21 Mbyte, inner zone 31 831 ftprad, outer zone 47 747ftprad, for sector servo tracking. ISODEC 9983:1995 (E) 0 ISOLIEC 3 Specification of the identifier The identifier shall consist of the word Type followed by three digits XYZ. - digit X shall identify FDCs of the sam
31、e size. X = 1 shall identify FDCs of 200 mm (8 in) X = 2 shall identify FDCs of 130 mm (5,25 in) X = 3 shall identify FDCs of 90 mm (3,5 in) When needed, further values of X may be included in future editions of this International Standard. - digits YZ shall be a two-digit serial number starting wit
32、h 01. 4 Information on packages The information on packages shall include the following: - the identifier; - a statement that the FDCs conform to an identified International Standard; - the size; - the number of recordable sides; - the number of tested tracks per side; - the unformatted capacity exp
33、ressed in number of bytes. This information shall be presented as shown and preferably within a frame. 5 Information 0 IS0 Type XYZ These flexible disk cartridges conform to International Standard IS0 . . Size: . . . mm (. in) Recordable sides: . . Tested tracks per side: . . . Unformatted capacity:
34、 . . . bytes I the flexible disk cartridge The flexible disk cartridge shall bear at least the identifier: IS0 Type XYZ. 6 Allocation of type numbers In each International Standard for flexible disk cartridges the identifier number shall be specified. 7 Type numbers of already published Internationa
35、l Standards The flexible disk cartridges according to International Standards already issued shall be identified as follows (see annex A): Type 101: IS0 5654-l Type 102: IS0 7065-l Type 201: IS0 6596-l Type 202: ISO/IEC 7487-l Type 203: IS0 8378-l Type 204: IS0 8630-l 2 0 ISOAEC Type 301: IS0 8860-l
36、 Type 302: ISO/IEC 9529-l Type 303: ISO/IEC 10994 Type 304: ISOAEC 13422 Type 305: ISO/IEC 14169 ISO/IEC 9983:1995 (E) ISO/IEC 9983:1995 (E) 0 ISO/IEC Annex A (informative) Main characteristics of FDCs available Type 101 102 201 202 203 204 301 302 303 304 305 International Standard IS0 5654-l IS0 7
37、065-l IS0 6596-l ISO/IEC 7487-l IS0 8378-l IS0 8630-l IS0 8860-I ISO/IEC 9529- 1 ISOAEC 10994 ISO/IEC 13422 ISO/IEC 14169 Size mm (in) 200 (8) 200 (8) 130 (5,25) 130 (5,25) 130 (5,25) 130 (5,25) 90 (3,5) 90 (3,5) 90 (3,5) 90 (3,5) 90 (395) Number of recordable sides 1 2 1 2 2 2 2 2 2 2 2 Tested trac
38、ks per side Unformatted capacity Mbytes I 77 034 77 136 35 (41 40 095 80 1s 80 136 80 130 80 230 80 430 255 10,o 326 21,0 4 ISO/IEC 9983:1995(E) 0 ISO/IEC ICS 35.220.20 Descriptors: data processing, information interchange, data recording devices, magnetic disks, flexible disks, flexible disk cartridges, designation. Price based on 4 pages
