ANSI SAE J561-1993 Electrical Terminals - Eyelet and Spade Type《电气接线端-小孔和薄片型》.pdf
《ANSI SAE J561-1993 Electrical Terminals - Eyelet and Spade Type《电气接线端-小孔和薄片型》.pdf》由会员分享,可在线阅读,更多相关《ANSI SAE J561-1993 Electrical Terminals - Eyelet and Spade Type《电气接线端-小孔和薄片型》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、SURFACEVEHICLESTANDARDJ561REAF.NOV2010Issued 1918-08Reaffirmed 2010-11Superseding J561 APR2006Electrical TerminalsEyelet and Spade Type1. ScopeThis SAE Standard covers general requirements and dimensions of various sizes of eyelet andspade type terminals.1.1 RationaleJ561 has been reaffirmed to comp
2、ly with the SAE 5-Year Review policy.2. References2.1 Applicable PublicationThe following publications form a part of this specification to the extent specifiedherein. The latest issue of SAE publications shall apply.2.1.1 SAE PUBLICATIONAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 150
3、96-0001, Tel:877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J163Low Tension Wiring and Cable Terminals and Splice Clips3. General RequirementsThe eyelet and spade type terminals listed in Tables 1A and 1B and Figures 1through 5 of this document may be used for te
4、rminating wire ends or for terminating circuits on devices otherthan wire. Performance requirements for low tension wire terminals are specified in SAE J163.Terminal sizes other than those listed are permissible, providing they meet the general requirements of thisdocument and the performance requir
5、ements of SAE J163.Terminals shall be free from burrs, corrosion, or any foreign matter, and shall be of a temper that will permitattachment to wires or circuits on devices without fracturing or cracking.Terminals may be applied to wire by crimping, welding, swaging, soldering, or any combination th
6、ereof at theconductor grip. Insulation grips shall be used on all terminals assembled to 8 gage (8 mm2) and smallerinsulated wire except where usage provides other means of relieving strain.Materials should be of copper, brass, or other copper alloys. Minimum metal thickness is the nominalthickness
7、shown less a standard strip stock tolerance. Thickness is based on SAE CA260 (UNS C26000)brass conductivity and may be adjusted for use with other materials. Unless otherwise noted, all dimensionsshall be held to a tolerance of 0.25 mm ( 0.010 in).SAE Technical Standards Board Rules provide that: “T
8、his report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE rev
9、iews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or tran
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSISAEJ5611993ELECTRICALTERMINALSEYELETANDSPADETYPE 电气 接线 小孔 薄片 PDF

链接地址:http://www.mydoc123.com/p-437900.html