1、i TDMA Third Generation Wireless - i Mobile Stations Minimum Performance ANSI/TIA/EIA-136-270-C-l-2002 Approved: January 31, 2002 Addendum 1 TIA/EIA STANDARD TIA/EIA- 136-270-C- 1 1 (Addendum No. 1 to TIA/EIA-136-270-C) 1 JANUARY 2002 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Teleconmiunications I
2、ndustry Association represents the conmiunications sector of NOTICE TIA/EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and as
3、sisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or selling products not conforming to such Standards an
4、d Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIA/EIA in accordance with the American Na
5、tional Standards Institute (ANSI) patent policy. By such action, TIA/EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Note: The users attention is called to the possibility that compliance with this doc
6、ument may require use of one or more inventions covered by patent rights. By publication of this standard, Interim Standard, or TSB, no position is taken with respect to the validity of those claims or of any patent rights in connection therewith. The patent holder) so far identijied have, however,
7、jiled statements of willingness to grant licenses under those rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such licenses. Details may be obtained from the standards developer. This Standard does not purport to address all safety problems associated
8、 with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 4027-270-C-AD1, formulated und
9、er the cognizance of the TIA TR-45.3 Subcommittee on Time Division Digital Technology.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2002 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 2220 1 PRICE: Please refer to current Catalog of EIA ELECTRONIC INDUSTRIES ALLIANC
10、E STANDARDS and ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1 -800-854-7 179) International (303-397-7956) All rights reserved Printed in U.S.A. NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed has been prepared by one o
11、r more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees are expected
12、 to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.orZr/standards/sfZr/engineering manual.ch. TIAS function is to administer the process, but not the content, of document preparation i
13、n accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNE
14、D BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE
15、 TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FORA PARTICUL
16、AR PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. OR USE, ITS MERCHANTABILITY AND ITS NON-
17、INFRINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS
18、, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTEN
19、TS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TINEIA- 136-270-C-AD 1 I 2.2.4.2.2 Method of Measurement i 3 4 5 6 7 8 9 10 II 12 2.2.4.2.3 Measurements shall be perfoimed between an input at the virtual interface preceding the D/A converter and the output of th
20、e reconstruction filter. The D/A converter shall be measured for distortion according to the ITU-T (formerly CCITT) recommendations in G.7 14, “Total distortion, including quantizing distortion“. The output reconstruction filter shall be measured according to the ITU-T (formerly CCITT) recommendatio
21、ns in G.714, “Attenuatiodfrequency distortion of the send or receive side, Method 2“. For the purpose of compliance with network transmission plans and for optimum operation of the codecs, the PCM interfaces to the TIA/EIA-136-420, TIAIEIA-136-410 or TIA/EIA-136- 430 coders are operated such that th
22、e maximum undistorted sinusoidal level (Tma) that can be transmitted through these interfaces is equivalent to a level of +3.16 dBmO. Minimum Standard 13 14 15 16 17 The total distortion with the proper noise weighting (see ITU-T (formerly CCITT) Table 4/G.223) shall lie above the limits shown in fi
23、gure 5/G.714 of the ITU-T (formerly CCITT) G.7 14 recommendations. The frequency response of the reconstiuction filter shall lie within the limits of the mask in figure 2/G.714 in ITU-T (foimerly CCITT) recommendations G.7 14. 18 2.2.4.3 Audio Freauencv Remonse 19 2.2.4.3.1 Definit ion 20 21 22 23 2
24、4 25 26 2.2.4.3.2 The audio frequency response of the digital voice receiver is defined as the variation of the ratio of the acoustic output of the receiver to the signal input to a reference encoder as a function of frequency. For the purposes of this test any encoder with which the decoder in the
25、receiver under test has met the requirements described in T1A/EL4-136-210.4CELP XIAIEI A- 136-.44O) may be used as the reference encoder. Mi:/ivttu P:/Y/MLc? (TTAIETA-136-4 i O, TIAIEIA-136-420, TIAIEIA-136-430, Method of Measurement 27 28 29 The receiver frequency response is measured using the con
26、tinuous-spectrum signal (ITU- T (formerly CCITT) P.50) according to IEEE 269-1992, Standard Methods for Measuring Transmission Performance of Analog and Digital Telephone Sets. 30 2.2.4.3.3 Minimum Standard 31 32 33 The receiver frequency response shall lie within the mask created by the upper and l
27、ower boundary limits formed by separately joining the sets of turning points defined in Table 2.2.4.3.3 - 1 by straight lines. 18 TINEIA- 136-270-C-AD 1 Frequency o. 1 0.2 0.3 1 .o 2.0 3.0 3.4 4.0 (ICH4 I 2 Upper Limit Lower Limit -4 -00 +2 -00 +2 -12.5 +2 -2 +14 -2 +14 -9 +14 -00 -4.8 -00 (dB) (dB)
28、 weighting (see ITU-T (formerly CCITT) Table 4/G.223) shall lie above the limits shown in figure 5/G.714 of the ITU-T (formerly CCITT) G.714 recommendations. 3 3.3.2.2.2 Transmit Audio Freauencv Remonse 4 3.3.2.2.2.1 Definit ion 8 9 10 The audio frequency response of the digital voice transmitter is
29、 defined as the variation of the ratio of the output from a reference decoder to the acoustic input to the transmitter as a function of fi-equency. For the purposes of this test any decoder with which the encoder in the transmitter under test has met the requirements described in TY.4EIA-136-210 ACE
30、LF Mizimum Peg Alliance NOTICE TIMEIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and
31、 obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIMEIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence
32、 of such Standards and Publications preclude their voluntary use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (ANSI) paten
33、t policy. By such action, TIA/EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Note: use of one or more inventions covered by patent rights. By publication of this standard, Interim Standard, or TSB, no
34、 position is taken with respect to the validity of those claims or of any patent rights in connection therewith. The patent holder(s) so far identijed have, however, $led statements of willingness to grant licenses under those rights on reasonable and nondiscriminatory terms and conditions to applic
35、ants desiring to obtain such licenses. Details rnay be obtained from the standards developer. The users attention is called to the possibility that compliance with this document rnay require This Standard does not purport to address all safety problems associated with its use or all applicable regul
36、atory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standard Proposals NO. 4027-270-C, formulated under the cognizance ofthe TIA TR-45.3 Subco
37、mmittee on Time Division Digital Technology.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2001 Standards and Technology Department 2500 Wilson Boulevard Arlingon, VA 22201 PRICE: Please refer to current Catalog of EIA ELECTRONIC INDUSTRIES ALLIANCE STANDARDS and ENGINEERING PUBLICATIONS or
38、call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) All rights reserved Printed in U.S.A. TIA/EIA-136-27O-C CONTENT 1. INTRODUCTION 1 1.1 Scope 1 1.2 General Description of a Wireless Mobile Telephone System 1.3 Definition of a Mobile Station (Analog Mode
39、Operation) 1.3.1 Channel numbering and frequencies 1.3.2 Classes of Equipment 1.3.3 Duty Cycle 1.3.4 Full Duplex Operation 1.3.5 Time Intervals 1.4 Definition of Mobile Station (Digital Mode Operation) 1.4.1 Channel Numbering and Frequencies 1.4.2 Classes of Equipment 1.4.3 Duty Cycle 1.4.4 Reserved
40、 1.4.5 Time Intervals 1.5 Supplementary Terms and Definitions 2. RECEIVER MINIMUM STANDARDS 2.1 Frequency Requirements 2.1.1 Frequency Coverage 2.1.2. Synchronization Acquisition Time (Digital Mode) 2.1.2.1 Definition 2.1.2.2 Method of Measurement 2.1.2.3 Minimum Standard 2.2 Demodulation Requiremen
41、ts 2.2.1 Type of Modulation 2.2.1 .I Analog 2.2.1.2 Digital 2.2.2.1 Electrical Audio Frequency Response 2.2.2 Demodulated Analog Voice Signals 2.2.2.1 .I Definition 2.2.2.1.2 Method of Measurement 2.2.2.1.3 Minimum Standard 2.2.2.2 Audio Muting 2.2.2.2.1 Definition 2.2.2.2.2 Method of Measurement 2.
42、2.2.2.3 Minimum Standard 2.2.2.3 Expandor 2.2.2.3.1 Definition 2.2.2.3.2 Method of Measurement 2 7 9 9 9 9 9 9 10 10 10 10 10 11 11 11 11 11 12 12 12 12 12 12 12 i TIA/EIA-136-27O-C 2.2.2.3.3 Minimum Standard 2.2.2.4.1 Definition 2.2.2.4.2 Method of Measurement 2.2.2.4.3 Minimum Standard 2.2.2.5 Aud
43、io Harmonic Distortion 2.2.2.5.1 Definition 2.2.2.5.2 Method of Measurement 2.2.2.5.3 Minimum Standard 2.2.2.6 Receive Audio Sensitivity 2.2.2.6.1 Definition 2.2.2.6.2 Method of Measurement 2.2.2.6.3 Minimum Standard 2.2.2.7.1 Definition 2.2.2.7.2 Method of Measurement 2.2.2.7.3 Minimum Standard 2.2
44、.3.1 Manchester Decoding 2.2.3.2 2.2.2.4 Hum and Noise 2.2.2.7 Receive Audio Frequency Response 2.2.3 Demodulated Data and Control Signals Supervisory Audio Tone (SAT) Decoding 2.2.3.2.1 Definition 2.2.3.2.2 Method of Measurement 2.2.3.2.3 Minimum Standard 2.2.4 Demodulated Digital Voice Signals 2.2
45、.4.1 Receive Audio Sensitivity 2.2.4.1 .I Definition 2.2.4.1.2 Method of Measurement 2.2.4.1.3 Minimum Standard 2.2.4.2.1 Definition 2.2.4.2.2 Method of Measurement 2.2.4.2.3 Minimum Standard 2.2.4.3 Audio Frequency Response 2.2.4.3.1 Definit ion 2.2.4.3.2 Method of Measurement 2.2.4.3.3 Minimum Sta
46、ndard 2.2.4.2 D/A Converter and Reconstruction Filter 2.3 Receiver Performance 2.3.1 Analog 2.3.1 .I RF Sensitivity 2.3.1 .I .I Definition 2.3.1 .I .2 Method of Measurement 2.3.1 .I .3 Minimum Standard 2.3.1.2.1 Definition 2.3.1.2.2 Method of Measurement 2.3.1.2.3 Minimum Standard 2.3.1.3.1 Definiti
47、on 2.3.1.3.2 Method of Measurement 2.3.1.3.3 Minimum Standard 2.3.1.2 Adjacent and Alternate Channel Desensitization 2.3.1.3 Intermodulation Spurious Response Attenuation 2.3.1.4 Protection Against Spurious-Response Interference 13 13 13 13 13 14 14 14 14 14 14 14 14 15 15 15 15 15 15 16 16 16 16 17
48、 17 17 17 17 17 17 18 18 18 18 18 18 19 19 19 19 19 20 20 20 20 21 21 21 21 22 22 11 TIA/EIA-136-27O-C 2.3.1.4.1 Definition 22 2.3.1.4.2 Method of Measurement 22 2.3.1.4.3 Minimum Standard 23 2.3.1.5 Bit-Error Rate 23 2.3.1 5.1 Definition 23 2.3.1 5.2 Method of Measurement 23 2.3.1 5.3 Minimum Stand
49、ard 24 2.3.2 Digital 24 2.3.2.1 Receiver Signal Level Range Capability 24 2.3.2.1 .I Static and Faded 24 2.3.2.1 .I .I Definition 24 2.3.2.1 .I .2 Method of Measurement 25 2.3.2.1 .I .3 Minimum Standard 26 2.3.2.2 Adjacent and Alternate Channel Desensitization 26 2.3.2.2.1 Definition 26 2.3.2.2.2 Method of Measurement 27 2.3.2.2.3 Minimum Standard 27 2.3.2.3 Intermodulation Spurious Response Attenuation 27 2.3.2.3.1 Definition 27 2.3.2.3.2 Method of Measurement 27 2.3.2.3.3 Minimum Standard 28 2.3.2.4 Blocking and Spurious-Response Rejection 29 2.3.2.4.1 Defin
