1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 19 Lined Fire Hose and Hose AssembliesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FUR
2、THER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Lined Fire Hose and Hose Assemblies, UL 19 Thirteenth Edition, Dated October 25, 2013 SUMMARY OF TOPICS This new edition of ANSI/UL 19 includes the following: 1. Revision to scope to update NFPA standard title 2.
3、 Revision regarding length of hose 3. Revision to correct typographical error and to add 200 psi service test pressure rating for single jacketed hose in the 2-1/2 to 6 inch size 4. Revision to Kink Test to remove hose assemblies 5. Revision to Repeated Bending Test 6. Revision to Abrasion Test with
4、 respect to sample length 7. Revision to Heat Resistance Test with respect to tolerance 8. Revision to Fold Resistance Test with respect to tolerance 9. Revision to Wet Hose Test clarifying when to conduct Hydrostatic Strength Test 10. Revision to Low Temperature Test with respect to tolerance 11. R
5、evision to Friction Loss Test clarifying test method 12. Revision to Accelerated Aging Test of Threads with respect to tolerance 13. Revision to Accelerated Aging Test of Linings and Covers with respect to tolerance 14. Revision to Ozone-Exposure Test of Linings and Covers with respect to outside re
6、ference 15. Revision to Water Immersion Test of Linings with respect to tolerance 16. Revision to Pull Test with respect to minimum required pull force 17. Revision to Accelerated Aging Test of Hose Assembly with respect to tolerance 18. Revision to Accelerated Aging Test of Gaskets with respect to
7、tolerance The revised requirements are substantially in accordance with Proposal(s) on this subject dated June 21, 2013. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, rec
8、ording, or otherwise without prior permission of UL. OCTOBER 25, 2013 UL 19 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limit
9、ed to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to us
10、e this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for S
11、afety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system.
12、 The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a
13、 future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. OCTOBER 25, 2013 UL 19 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 25, 2013 1 UL 19 Standard for Lined Fire Hose and
14、Hose Assemblies The First through Sixth editions were titled Cotton Rubber-Lined Hose. First Edition July, 1914 Second Edition March, 1931 Third Edition December, 1937 Fourth Edition August, 1941 Fifth Edition April, 1948 Sixth Edition August, 1953 Seventh Edition August, 1967 Eighth Edition October
15、, 1971 Ninth Edition March, 1978 Tenth Edition December, 1992 Eleventh Edition December, 1995 Twelfth Edition November, 2001 Thirteenth Edition October 25, 2013 This ANSI/UL Standard for Safety consists of the Thirteenth Edition. The most recent designation of ANSI/UL 19 as an American National Stan
16、dard (ANSI) occurred on October 24, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. The Department of Defense (DoD) has adopted UL 19 on April 5, 1999. The publication of revised pages or a new edition of this Standard
17、 will not invalidate the DoD adoption. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are cop
18、yrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC. ANSI/UL 19-201
19、3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CO
20、NTENTS INTRODUCTION 1 Scope .7 2 General 7 2.1 Units of measurement .7 2.2 Undated references .7 3 Glossary .7 CONSTRUCTION 4 Internal Diameter .8 5 Jacket and Inner Reinforcements .8 6 Lining 9 7 Cover 9 8 Coatings and Treatments 9 9 Couplings 9 PERFORMANCE 10 Hydrostatic Proof-Pressure Tests .10 1
21、0.1 General .10 10.2 Sample .11 10.3 Equipment .11 10.4 Test method .11 11 Kink Test 13 11.1 General .13 11.2 Sample .13 11.3 Equipment .13 11.4 Test method .13 12 Hydrostatic Strength Test 13 12.1 General .13 12.2 Sample .14 12.3 Equipment .14 12.4 Test method .14 13 Repeated Bending Test .14 13.1
22、General .14 13.2 Sample .14 13.3 Equipment .15 13.4 Test method .16 14 Alternating Pressure Test 16 14.1 General .16 14.2 Sample .16 14.3 Equipment .16 14.4 Test method .17 15 Abrasion Test 17 15.1 General .17 15.2 Sample .17 15.3 Equipment .17 15.4 Test method .18 16 Heat-Resistance Test .18 OCTOBE
23、R 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 16.1 General .18 16.2 Sample .18 16.3 Equipment .18 16.4 Test method .18 17 Fold-Resistance Test 19 17.1 General .19 17.2 Sample .19 17.3
24、 Equipment .19 17.4 Test method .19 18 Wet Hose Test .19 18.1 General .19 18.2 Sample .20 18.3 Test method .20 19 Low-Temperature Test 20 19.1 General .20 19.2 Sample .20 19.3 Equipment .20 19.4 Test method .20 20 Coupling Retention Test .21 20.1 General .21 20.2 Sample .21 20.3 Equipment .21 20.4 T
25、est method .21 21 Friction Loss Test .21 21.1 General .21 21.2 Sample .22 21.3 Equipment .22 21.4 Test method .22 22 Accelerated Aging Test of Threads .23 22.1 General .23 22.2 Sample .23 22.3 Equipment .23 22.4 Test method .23 23 Adhesion Tests .23 23.1 General .23 23.2 Sample .24 23.3 Equipment .2
26、4 23.4 Test method .24 24 Accelerated Aging Test of Linings and Covers .25 24.1 General .25 24.2 Sample .25 24.3 Equipment .25 24.4 Test method .26 25 Ozone-Exposure Test of Linings and Covers .27 25.1 General .27 25.2 Sample .27 25.3 Equipment .27 25.4 Test method .27 26 Water Immersion Test of Lin
27、ings .27 26.1 General .27 26.2 Sample .28 26.3 Equipment .28 26.4 Method Effect on tensile strength and ultimate elongation .28 OCTOBER 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 26.
28、5 Method Effect on volume 29 27 Pull Test .29 27.1 General .29 27.2 Sample .29 27.3 Test method .29 28 Accelerated Aging Test of Hose Assembly .29 28.1 General .29 28.2 Sample .30 28.3 Equipment .30 28.4 Test method .30 29 Rough Usage Test 30 29.1 General .30 29.2 Sample .30 29.3 Equipment .30 29.4
29、Test method .30 30 Moist Ammonia-Air Stress Cracking Test 31 30.1 General .31 30.2 Sample .31 30.3 Equipment .31 30.4 Method .31 31 Salt-Spray Corrosion Test .32 31.1 General .32 31.2 Sample .32 31.3 Equipment .32 31.4 Test method .32 32 Accelerated Aging Test of Gaskets .33 32.1 General .33 32.2 Sa
30、mple .33 32.3 Equipment .33 32.4 Test method .33 33 Compression Set Test .33 33.1 General .33 33.2 Samples 33 33.3 Equipment .34 33.4 Test method .34 34 Ozone Resistance Test of Gaskets .34 34.1 General .34 34.2 Sample .34 34.3 Equipment .34 34.4 Test method .34 35 Water Immersion Test of Gaskets 35
31、 35.1 General .35 35.2 Sample .35 MANUFACTURING AND PRODUCTION TESTS 36 General 35 OCTOBER 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARKING 37 Details .35 37.1 General .35 37.2 Hos
32、e .36 37.3 Hose Assemblies .36 OCTOBER 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover single- and multiple-jacketed lined re hose with o
33、r without couplings attached, in the trade sizes of 1-1/2, 1-3/4, 2, 2-1/2, 3, 3-1/2, 4, 5, and 6 inch (38, 45, 51, 65, 76, 89, 102, 127, and 152 mm nominal ID). Single-jacketed hose is intended for service test pressures of 150, 200, or 250 psig (1035, 1380, or 1725 kPa). Multiple-jacketed hose or
34、covered hose judged equivalent to multiple-jacketed hose is intended for service test pressures of 200, 300, or 400 psig (1380, 2070, or 2760 kPa). 1.2 These products are intended for municipal and industrial re protection purposes. Single-jacketed hose is for use at re hydrants, standpipes, and sim
35、ilar places. They are not intended for hard usage nor where the hose will be subjected to chang on rough or sharp surfaces. Multiple-jacketed hose or covered hose judged equivalent to multiple-jacketed hose are for use on pumpers and in places where service conditions require the additional protecti
36、on against wear afforded by the extra woven jacket or cover. 1.3 The products covered by these requirements are intended to be periodically inspected and maintained while in service, as outlined in the Standard for the Care, Use, Inspection, Service Testing and Replacement of Fire Hose, Couplings, N
37、ozzles, and Fire Hose Appliances, NFPA 1962. 2 General 2.1 Units of measurement 2.1.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the req
38、uirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.2 EXPANSION RING A ring that expands against the hose lining, forcing the hose tightly against the coupling.
39、3.3 FILLER THREADS The threads or yarns of the jacket or reinforcement that are helically wound throughout the length of the hose at approximately right angles to the warp threads. 3.4 HOSE ASSEMBLY Hose furnished with couplings attached to each end. 3.5 MULTIPLE-JACKETED HOSE Hose having two or mor
40、e woven jackets or a covered hose that complies with all of the performance tests in this standard for multiple-jacketed hose. See 5.3. 3.6 PROOF PRESSURE A specied pressure applied to new hose to indicate its acceptability at intended maximum normal highest operating pressures. OCTOBER 25, 2013 LIN
41、ED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3.7 SERVICE TEST PRESSURE The pressure to which the hose is periodically tested to determine that it can remain in service. The service test pressure i
42、s at least 10 percent greater than the maximum normal highest operating pressure. 3.8 WARP THREADS The threads or yarns of the jacket or reinforcement that run lengthwise to the hose. CONSTRUCTION 4 Internal Diameter 4.1 Hose shall have an internal diameter of not less than the trade size of the hos
43、e. 4.2 A tapered plug gauge having a taper of 3/8 inch per foot (31.2 mm/m) marked to indicate variations of 1/64 inch (0.4 mm) in diameter, is to be used to measure the internal diameter. If the lining of the hose has a lap joint, the tapered plug gauge is to be provided with a slot to accommodate
44、the lap joint. 4.3 To determine the internal diameter, the end of the hose is to be cut square and the tapered plug gauge inserted in the hose sample until a close t is obtained without forcing. The diameter of the gauge at the end of the sample, to the nearest 1/64 inch (0.4 mm), is to be recorded
45、as the internal diameter of the hose. 5 Jacket and Inner Reinforcements 5.1 A jacket shall be evenly and rmly woven, and free from visible defects, thread knots, lumps, and irregularities of twist provided that they would not impair its intended use. The threads shall be continuous, and any knots in
46、 the ller threads shall be tucked under the warp threads. 5.2 A jacket shall be seamless and shall have the llers woven around the hose throughout its length and the warps interwoven with the llers. A jacket may be made with a cover over the woven jacket. 5.3 Hose having a woven jacket or hose havin
47、g an inner reinforcement and a protective cover may be considered equivalent to multiple-jacketed hose if it complies with the applicable performance requirements specied in this standard. OCTOBER 25, 2013 LINED FIRE HOSE AND HOSE ASSEMBLIES - UL 19 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHE
48、R REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6 Lining 6.1 A lining shall be of uniform thickness and free from pitting or other irregularities or imperfections and shall comply with the applicable test requirements specied in Sections 23 26. 7 Cover 7.1 A cover shall be of uniform thick
49、ness and free from pitting, blisters, or other imperfections that would impair its intended use, and shall comply with the applicable test requirements in Sections 23 25. 7.2 A cover may have intentional pricking, ribs, corrugations, or a wrapped nish. 8 Coatings and Treatments 8.1 Hose may have jackets with treatments or coatings if the hose complies with the applicable performance requirements in this standard. 9 Couplings 9.1 The couplings of hose assemblies shall be ma
