1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60745-2-1 Hand-Held Motor-Operated Electric Tools Safety Part 2-1: Particular Requirements for Drills and Impact Drills STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER
2、REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hand-Held Motor-Operated Electric Tools Safety Part 2-1: Particular Requirements for Drills and Impact Drills,
3、UL 60745-2-1 Second Edition, Dated March 26, 2004 Summary of Topics The revisions dated August 4, 2016 were issued to administratively update the ANSI approval of the Standard for Hand-Held Motor-Operated Electric Tools Safety Part 2-1: Particular Requirements for Drills and Impact Drills, UL 60745-
4、2-1. No technical changes are being incorporated into the standard. As noted in the Commitment for Amendments statement located on the back side of the title page, UL and CSA are committed to updating this harmonized standard jointly. However, the revision pages dated August 4, 2016 will not be join
5、tly issued by UL and CSA as these revision pages address UL only editorial changes. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are fol
6、lowed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photoco
7、pying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, i
8、ncidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no ev
9、ent shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or jud
10、gment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other el
11、ements of the Standard having future effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. AUGUST 4, 2016 UL 60745-2-1 tr1UL COPYR
12、IGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 4, 2016 UL 60745-2-1 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Canadian Standards Association CAN/CSA-C22
13、.2 No. 60745-2-1-04 Second Edition (IEC 60745-2-1:2003, MOD) Underwriters Laboratories Inc. UL 60745-2-1 Second Edition Hand-Held Motor-Operated Electric Tools Safety Part 2-1: Particular Requirements for Drills and Impact Drills March 26, 2004 (Title Page Reprinted: August 4, 2016) This national st
14、andard is based on publication IEC 60745-2-1, Edition 2.1 (2008). ANSI/UL 60745-2-1-2011 (R2016) Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Canadian Standards A
15、ssociation (CSA) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA or UL at any time. Revisions to this standard will be made only after processing according to the standards development procedures of CSA and UL. CSA and
16、UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 1-55397-465-4 2004 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. CS
17、A Standards are subject to periodic review, and suggestions for their improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send the following information to inquirescsa.ca and include Proposal for change in the subject line: Standard des
18、ignation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Standards and related publications, visit CSAs Online Store at www.ShopCSA.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2016 Underwriters Lab
19、oratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL
20、Standard for Safety consists of the Second Edition including revisions through August 4, 2016. The most recent designation of ANSI/UL 60745-2-1 as an American National Standard (ANSI) occurred on August 4, 2016. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title P
21、age (front and back), or the Preface. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Reques
22、t in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 NATIONAL
23、 DIFFERENCES .7 FOREWORD 8 1 Scope 11 2 Normative references 11 3 Terms and Denitions 11 4 General requirements 11 5 General conditions for the tests .11 6 Void 12 7 Classication 12 8 Marking and instructions 12 9 Protection against access to live parts .12 10 Starting 12 11 Input and current 12 12
24、Heating 13 13 Leakage current .13 14 Moisture resistance 13 15 Electric strength .13 16 Overload protection of transformers and associated circuits 13 17 Endurance 14 18 Abnormal operation 14 19 Mechanical hazards .15 20 Mechanical strength .15 21 Construction 15 22 Internal wiring .15 23 Components
25、 16 24 Supply connection and external exible cords .16 25 Terminals for external conductors .16 26 Provision for earthing 16 27 Screws and connections .16 28 Creepage distances, clearances and distances through insulation .16 29 Resistance to heat, re and tracking .16 30 Resistance to rusting 16 31
26、Radiation, toxicity and similar hazards .16 Figures 17 OCTOBER 6, 2010 CAN/CSA-C22.2 NO. 60745-2-1-04 UL 60745-2-1 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Annexes Annex K (normative) Battery tool and battery packs Annex L (normative
27、) Battery tools and battery packs provided with mains connection or non-isolated sources Annex 1.DVL List of National Differences Bibliography OCTOBER 6, 2010 CAN/CSA-C22.2 NO. 60745-2-1-04 UL 60745-2-1 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI
28、ON FROM UL Preface This is the harmonized CSA and UL standard for hand-held motor-operated electric tools; drills and impact drills. It is the second edition of CAN/CSA-C22.2 No. 60745-2-1 and the second edition of UL 60745-2-1. This standard is based on IEC 60745-2-1, second edition. This harmonize
29、d standard has been jointly revised on October 6, 2010. For this purpose, CSA and UL are issuing revision pages dated October 6, 2010. This harmonized standard was prepared by the Canadian Standards Association (CSA) and Underwriters Laboratories Inc. (UL). This standard was reviewed by the CSA Subc
30、ommittee on Portable Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approve
31、d as a National Standard of Canada by the Standards Council of Canada. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Where reference is made to a specic number of samples to be tested, the specied number is considered a minimum
32、quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. Level of harmonization This standard adopts the IEC text w
33、ith national differences. This standard is published as an equivalent standard for CSA and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as tho
34、se recognized as being in accordance with NAFTA Article 905, for example because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word except for editori
35、al changes. All national differences from the IEC text are included in the CSA and UL versions of the standard. While the technical content is the same in each organizations version, the format and presentation may differ. Interpretations The interpretation by the standards development organization
36、of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one literal interpretation has been identied, a revision is to be proposed as soon as possible
37、 to each of the standards development organizations to more accurately reect the intent. OCTOBER 6, 2010 CAN/CSA-C22.2 NO. 60745-2-1-04 UL 60745-2-1 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA effective date The effective date for C
38、SA International will be announced through CSA Informs or a CSA certication notice. UL effective date The effective date for UL 60745-2-1, Second edition is October 7, 2013. Between the present and October 7, 2013 new product submittals to UL must be evaluated under all requirements in this Standard
39、 or, if requested in writing, evaluated under presently effective requirements only. The presently effective requirements are contained in the Second edition of UL 745-2-1. As of October 7, 2013 all products Listed or Recognized by UL shall comply with the requirements in the Second edition of UL 60
40、745-2-1. A UL effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. OCTOBER 6, 2010 CAN/CSA-C22.2 NO. 60745-2-1-04 UL 60745-2-1 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NAT
41、IONAL DIFFERENCES In the CSA and UL publications of this standard, National Differences from the text of International Electrotechnical Commission (IEC) Publication 60745-2-1, Safety Requirements for Hand-Held Motor-Operated Electric Tools Safety Part 2-1: Particular Requirements for Drills and Impa
42、ct Drills, copyright 2008, are indicated by notations (differences) and are presented in bold text. The national difference type is included in the body. There are ve types of National Differences as noted below. The difference type is noted on the rst line of the National Difference in the standard
43、. The standard may not include all types of these National Differences. DR These are National Differences based on the national regulatory requirements. D1 These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise safety for con
44、sumers and users of products. D2 These are national differences from IEC requirements based on existing safety practices. These requirements reect national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been included in the
45、 IEC standard. DC These are National Differences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE These are National Differences based on editorial comments or corrections. Each national difference contai
46、ns a description of what the national difference entails. Typically one of the following words is used to explain how the text of the national difference is to be applied to the base IEC text: Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, gure, or anne
47、x. Addition is not meant to include adding select words to the base IEC text. Modication / Modify - A modication is an altering of the existing base IEC text such as the addition, replacement or deletion of certain words or the replacement of an entire clause, subclause, table, gure, or annex of the
48、 base IEC text. Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause, table, gure, or annex without any replacement text. OCTOBER 6, 2010 CAN/CSA-C22.2 NO. 60745-2-1-04 UL 60745-2-1 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRI
49、BUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-1: Particular requirements for drills and impact drills FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international c
