1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to U.S. Army Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS#268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emai
2、led to DAMI_STANDARDIZATIONconus.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. ASMC N/A FSC 4930 INCH-POUND A-A-50202A 1 September 2011 SUPERSEDING A-A-50202 6 May 1983 C
3、OMMERCIAL ITEM DESCRIPTION PUMP, BUCKET, LUBRICATION, HAND-OPERATED The General Services Administration has authorized the use of this Commercial Item Description (CID) as a replacement for MIL-P-13218 for all federal agencies. 1. SCOPE. This CID covers hand-operated portable bucket pumps furnished
4、with a cover and locking device which fits and dispenses grease or oil from bulk or a standard 35-pound bucket container. 2. CLASSIFICATION. The pumps shall be of the following types (see 7.3): Type I - Grease Type II - Oil 3. SALIENT CHARACTERISTICS. 3.1 Design and construction. 3.1.1 Type I. Type
5、I pumps shall be furnished with a hand-operated pressure pump, 10-foot length, heavy duty 3/8-inch internal diameter (ID) hose, follower plate, T-handle type nozzle and other required components. (Typical use: automotive, farm, construction type greases.) 3.1.2 Type II. Type II pumps shall be furnis
6、hed with a hand-operated pressure pump, 5-foot length, 1/2-inch ID hose, gooseneck type nozzle and other required components. (Typical use: SAE 75W, 80W-90, 140W gear lubricants, automatic transmission fluids and motor oils.) Provided by IHSNot for ResaleNo reproduction or networking permitted witho
7、ut license from IHS-,-,-A-A-50202A 2 3.2 Performance. The pumps shall meet the performance requirements of Table I while using the following lubricants: Type I - use lubricant conforming to MIL-PRF-10924 Type II - use grade SAE 75W or SAE 80W-90 gear lubricant conforming to SAE J2360 Table I. Pump p
8、erformance requirements. Function Type I Type II Minimum rate of discharge (at 70 F) 8 ounces (oz.) per minute with maximum of 50 strokes 2.5 pounds (lb.) per minute with maximum of 50 strokes Minimum rate of discharge (at 0 F) 7 oz. per minute with maximum of 50 strokes 1.75 lb. per minute with max
9、imum of 50 strokes Minimum rate of discharge (at minus (-) 25 F) 4 oz. per minute with maximum of 50 strokes 1 lb. per minute with maximum of 50 strokes Minimum rate of discharge (at back pressure of 5000 pounds per square inch gauge (psig) at 70 F) 1 oz. in not more than 30 seconds with continuous
10、pumping No requirement Maximum static pressure developed by pressure pump (at all specified temperatures) 7000 psig 500 psig 3.3 Identification and marking. Each pump shall be marked for identification with the National Stock Number (see 7.3). 4. REGULATORY REQUIREMENTS 4.1 Recovered material. The o
11、fferor/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Responsibility for inspection. The contractor is responsible for the performance of all
12、 inspections (examinations and tests). 5.2 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, workmanship stand
13、ards, and quality assurance practices. Items with known defects shall not be submitted for Government Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50202A 3 acceptance. The Government reserves the right to require proof of such conformance prio
14、r to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 6. PACKAGING. Preservation, packaging, packing, labeling and marking for the desired level shall be as specified in the contract (see 7.3). 7. NOTES (This section contains information of a g
15、eneral or explanatory nature that may be helpful, but is not mandatory.) 7.1 Part or Identification Number (PIN). The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. AA 50202 - 1 Type: 1 - Type I Grease 2 - Typ
16、e II Oil CID number CID designator 7.2 Addresses for obtaining copies of referenced documents. 7.2.1 Government publications. Copies of MIL-PRF-10924, “Grease, Automotive and Artillery”, are available from https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 R
17、obbins Avenue, Building 4D, Philadelphia, PA 19111-5094. The Federal Acquisition Regulation (FAR) may be obtained from http:/www.acquisition.gov/far/. 7.2.2 Non-Government publications. Copies of SAE J2360, “Lubricating Oil, Gear Multipurpose (Metric) Military use”, are available from www.sae.org or
18、 SAE Customer Service, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) 7.3 Ordering data. Acquisition documents should specify the following: a. Title, number, and date of this CID. b. If required, the specified issue of individual documents referenced. c. Type, National Stock Number (NSN), and
19、quantity of pumps required (see 2 and 3.3). d. Selection of applicable level and packaging requirements (see 6). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50202A 4 7.4 Cross reference. Pumps conforming to this CID are interchangeable or sub
20、stitutable with pumps conforming to MIL-P-13218. 7.5 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - AT Army - AT Navy - YD Air Force - 99 Age
21、nt Activity: DLA - CC Review Activity: DLA - CC Project 4930-2011-002 Navy - MC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
