1、 A-A-59102B September 1, 2009 SUPERSEDING A-A-59102A June 2, 2008 COMMERCIAL ITEM DESCRIPTION TABLES, ALUMINUM, GENERAL PURPOSE The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE 1.1 Scope. This commercial item descriptio
2、n(CID)covers general purpose aluminum tables with folding legs. 1.2 Intended use. The aluminum tables will be used as work tables and dining tables in a field environment. 2. CLASSIFICATION 2.1 Classification. The tables shall conform to the following types, sizes, and colors as specified (see 7.1).
3、 Type I - Nonadjustable legs Size 1 - 36 inches wide x 72 inches long x 29 inches high, with a maximum weight of 48 pounds. Size 2 - 36 inches wide x 96 inches long x 29 inches high, with a maximum weight of 60 pounds. Size 3 - 30 inches wide x 48 inches long x 29 inches high, with a maximum weight
4、of 30 pounds. Size 4 - 30 inches wide x 48 inches long x 36 inches high, with a maximum weight of 35 pounds. FSC 7195 INCH-POUND Comments, suggestions or questions on this document should be addressed to US Army Research, Development and Engineering Command, Natick Soldier Center, AMSRD-NSC-CF-S, 15
5、 Kansas St., Natick, MA 01760-5018, or emailed to Robert.Bernazzanius.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or network
6、ing permitted without license from IHS-,-,-A-A-59102B Type II - Adjustable legs Size 5 - 30 inches wide x 48 inches long with adjustable legs from 24 1/2 to 34 1/2 inches high with a maximum weight of 42 pounds. Color 1 - Green Color 2 - Tan Color 3 - Commercial color selection 3. SALIENT CHARACTERI
7、STICS 3.1 Design and construction. The tables shall be of the types, sizes, and colors as specified (see 2.1 and 7.1). The tables shall have legs which can be folded flat against the table bottom. The maximum folded depth of the legs shall not exceed 4 1/2 inches maximum projection out from the unde
8、rside of the table in order to permit nesting of the tables for storage and transportation. The size 5 table shall have legs that are adjustable in 1-inch increments to permit the height of the table to range from 24 1/2 to 34 1/2 inches. All exposed surfaces on corners, edges, and tabletop shall be
9、 smooth with no visible protrusions. The table top shall be constructed with integral stiffener ribs. 3.2 Load capacity. The table in its fully opened position, shall support a uniformly distributed static load of 1600 pounds without collapsing or exhibiting permanent deformation of the tabletop, fr
10、ame or leg assemblies. 3.3 Finish. The table shall have a fade, chip and scratch resistant, fused epoxy polyester powder-coated finish. 3.4 Color. The color of the table shall be either green (color 1), tan(color 2) or commercial color (color 3) as specified (see 7.1 and 7.4). Tables of a specific l
11、ot shall not exhibit any variation in shade from the specific color selected and specified in the contract for the production lot. Color 3 tables shall not reflect a “government unique“ requirement, but shall be selected from the manufacturers standard commercial colors. The selected color shall be
12、cited in the contract or purchase order. 3.5 Legs. The legs shall have positive acting locking devices when the table is fully opened. Leg bottoms shall be equipped with tips or caps for floor protection. Adjustable and non-adjustable folding leg assemblies shall have H style construction. 2 Provide
13、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59102B 3.6 Drop test. A folded table shall be capable of being dropped on each corner from a height of 2 feet onto a smooth hard surface without structural damage such as cracking, crushing, or damage that
14、 affects performance. 3.7 Finish temperature resistance. The tabletop finish shall not exhibit evidence of blistering, discoloring or cracking after direct contact with a hot object having a temperature of no more than 160OF for 10 minutes. 3.8 Operating conditions. The tables shall be capable of wi
15、thstanding extreme weather conditions, i.e., rain/sun/snow and temperatures of -25OF to 120OF without exhibiting any evidence of corrosion or mechanical degradation. 3.9 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inc
16、h-pound units, provided they fall within the tolerances specified using conversion tables contained in the latest revision of IEEE/ASTM SI10, and all other requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in
17、 the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 4. REGULATORY REQUIREMENTS 4.1 Contractor-recovered materials. The offeror/contractor is encouraged to u
18、se recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance provisions. The tables provided shall meet the salient characteristics of this commercial item descript
19、ion, shall conform to the producers own drawings, specifications, standards and quality assurance practices, and be the same product that has been sold in the commercial marketplace, or is the same product that has successfully been delivered to the Government on a previous contract or purchase orde
20、r. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59102B 5.2 M
21、arket acceptability. The following market acceptability criteria are necessary to document the quality of the aluminum tables to be provided under this commercial item description. a. The company producing the tables meeting the requirements of this CID must have been producing these items for at le
22、ast 2 years. b. The company must have sold at least 250 tables meeting the requirements of this CID in the commercial or government marketplace over the last 2 years. 6. PACKAGING 6.1 Packaging. Preservation, packing and marking shall be as specified in the contract or purchase order (see 7.1). 7. N
23、OTES 7.1 Ordering data. Acquisition documents must specify the following: a. Title, number and date of this document b. Type, size, and color required (see 2.1) c. Packaging requirements (see 6.1) 7.2 Sources for non-government association documents: AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
24、 INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS SI10 Standard for Use of the International Systems of Units (SI): The Modern Metric System may be obtained from: Institute of Electrical and Electronics Engineers, Inc., 305 East 47th Street, New York, NY 10017, www.ieee.org; or the American Society
25、 for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, or online at www.astm.org 7.3 Sources of supply. Manufacturers whose products are known to meet the requirements of, this document in whole or in part are listed below; however, competition is not limited to these c
26、ompanies. Southern Aluminum Manufacturing, Inc Highway 82 West P.O. Box 884 Magnolia, AR 71754 Tel: 800-221-0408 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59102B 7.4 Table color. Past experience has shown that a table with a green color c
27、onforming to No.34095, or a tan color conforming to No.33446 of FED-STD-595 were found to be acceptable. 7.5 Part identification number(PIN). The PINs to be used for items required by this CID are as follows: AA 59102 -1 -A -1 (Example of a PIN: AA59102-1-A-1) Type: 1-Type I 2-Type II Size: A-Size 1
28、 B-Size 2 C-Size 3 D-Size 4 E-Size 5 Color: 1-Green 2-Tan 3-Commercial Color Selection CID Number Designates a Commercial Item Description MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians GSA-FAS Army GL Preparing Activity Navy YD Air Force 99 Army GL Review Activities Project No.
29、7195-2009-002 Army QM1 Navy CG, MC Air Force 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
