1、Comments, suggestions, or questions on this document should be emailed to usarmy.APG.cerdec.mbx.standardization-crxmail.mil Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil/ AMSC N/A F
2、SC 5940 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. . INCH-POUND A-A-59126B 28 March 2012 SUPERSEDING A-A-59126A 31 May 2011 COMMERCIAL ITEM DESCRIPTION SHEET TERMINALS, FEEDTHRU (INSULATED) AND TERMINALS, STUD (INSULATED AND NONINSULATED) The General Services A
3、dministration has authorized the use of this commercial item description (CID) as a replacement for MIL-T-55155 for all federal agencies. 1. SCOPE 1.1 Scope. This CID covers the requirements for insulated feedthru terminals and insulated and noninsulated stud terminals. 2. CLASSIFICATION. Items proc
4、ured under this CID shall be identified by part numbers as follows: AA59126/XX 0 H 01 CID Sheet Identifier Insulation Color Conductor Material Item Number And Finish 2.1 CID Sheet Identifier. The CID sheet identifier shall consist of the number of the CID, a slash (/) , and a two digit number denoti
5、ng the CID sheet covering the item. 2.2 Insulation Color. The insulation color is indicated by a single digit in accordance with Table I. For noninsulated terminals or natural color (other than polytetrafluoroethylene) insulated terminals, the letter “X” shall be used in place of the single digit. 2
6、.3 Conductor Material and Finish. The conductor material and finish is identified by a single letter (see 3.3.1). For example, “H” defines a brass terminal, tin-lead plated in accordance with SAE-AMS-P-81728, 0.0003 inch minimum thickness. 2.4 Item Number. The item number is indicated by a two-digit
7、 number. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59126B 2 Table I. Insulation color. Symbol Insulation Color 0 Black 1 Brown 2 Red 3 Orange 4 Yellow 5 Green 6 Blue 7 V
8、iolet 8 Gray 9 White 3. SALIENT CHARACTERISTICS 3.1 CID Sheets. The individual item requirements shall be as described herein and in accordance with the applicable CID sheet. In the event of any conflict between the requirements of this CID and the CID sheet, the latter shall govern. 3.2 Materials.
9、Unless otherwise specified herein, materials shall conform to the manufacturers specifications/standards. The use of recycled or reclaimed materials is acceptable provided that all requirement of this CID are met (see 4.1). Materials shall be fungus inert. 3.3 Design and Construction. The terminals
10、shall conform to the manufacturers design and construction. The dimensions shall be in accordance with the individual CID sheet. 3.3.1 Conductor Material and Finish. The conductor material and finish shall be in accordance with one of the following. When so constructed and finished, the terminals sh
11、all be solderable. 3.3.1.1 Bronze. The conductor material shall be bronze and finished with one of the following. Copper underplate is not required. B - Tin-lead plated in accordance with SAE-AMS-P-81728, 0.0003 inch minimum thickness C - Hot solder dipped using Sn60/Pb40 Solder per IPC J-STD-006, 0
12、.0001 inch minimum thickness D - Tin-lead electrodeposited in accordance with ASTM B 545, 0.0003 inch minimum thickness. The minimum lead content shall be 3 percent. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking perm
13、itted without license from IHS-,-,-A-A-59126B 3 3.3.1.2 Brass. The conductor material shall be brass and finished with one of the following. Copper underplate of 0.0001 inch minimum thickness is required. H - Tin-lead plated in accordance with SAE-AMS-P-81728, 0.0003 inch minimum thickness I - Hot s
14、older dipped using Sn0/Pb40 Solder per IPC J-STD-006, 0.0001 inch minimum thickness J - Tin-lead electrodeposited in accordance with ASTM B 545, 0.0003 inch minimum thickness. The minimum lead content shall be 3 percent. 3.3.2 Mounting Bases. Mounting bases shall be constructed of brass and shall be
15、 plated with one of the following finishes (NOTE: Pure tin finish should not be used due to the potential for whiskering): (a) Tin-lead plated, 0.0001 inch minimum thickness provided that the minimum lead content is 3 percent. (b) Nickel plated in accordance with SAE-AMS-QQ-N-290, class I or II, 0.0
16、001 inch minimum thickness. 3.3.3 Mounting Hardware. Mounting hardware shall have a finish that is electrolytically compatible with the finish on the mounting base to avoid dissimilar metal corrosion. Pure tin finish should not be used so as to avoid the potential for whiskering. Mounting hardware,
17、including internal tooth lockwashers, shall be supplied with terminals. 3.3.4 Insulation Colors. Insulation colors shall be in accordance with Table I. Manufacturers standard (equivalent) colors are acceptable. 3.4 Performance. 3.4.1 Solderability. When a tinned copper wire is wrapped around the ter
18、minal or run through the terminal (depending on the configuration of the terminal) the connection shall be easily solderable with a soldering iron and rosin-core solder. The soldered joint shall have a smooth fillet over 95 percent of the interface between the wire and the terminal with no visible v
19、oids or dewetting. 3.4.2 Pull. The insulated terminals when mounted and subjected to an axial pull as specified on the individual CID sheet for at least 30 seconds, shall show no evidence of separation of the conductor from the insulation, or mounting base by more than 0.005 inch or of terminals pul
20、ling out of the mounting. 3.4.3 Torque. The insulated terminals, when mounted and subjected to a torque as specified on the individual CID sheet for at least 30 seconds, shall show no evidence of turning of the conductor within the insulation, or mounting base, or of terminals turning within the mou
21、nting. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59126B 4 3.5 Workmanship. Terminals shall be processed in such a manner as to be uniform in quality and shall be free fr
22、om any defects that affect life, serviceability or appearance. 4. REGULATORY REQUIREMENTS 4.1 Recovered Materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QU
23、ALITY ASSURANCE PROVISIONS 5.1 Contractor Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this Commercial Item Description, and that the product conforms to the producers own drawings, specifications, stan
24、dards, and quality assurance practices, and is the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5.2 Mar
25、ket acceptability (MA). The following market acceptability criteria are necessary to document the quality of the product to be provided under this CID. 5.2.1 The item offered must have been sold to the government or commercial market. 6. PACKAGING 6.1 The packaging requirements shall be as specified
26、 in the contract or order (see 7.1), Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59126B 5 7. NOTES 7.1 Ordering data. Acquisition documents must specify the following: a.
27、title, number, and date of this CID and the required slash sheet, and part number. b. Packaging requirement (see 6.1). MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY Custodian: GSA-7FXE Army - CR Navy EC Preparing activity: Air Force 85 Army CR Reviewer: (Project No. 5940-2012-001) DLA GS NO
28、TE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
