ARMY MIL-A-70604-1988 AMINE BONDING AGENT《胺粘接剂》.pdf
《ARMY MIL-A-70604-1988 AMINE BONDING AGENT《胺粘接剂》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-A-70604-1988 AMINE BONDING AGENT《胺粘接剂》.pdf(17页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-A-7060q 68 9797706 0322507 2 -* MIL-A-7 O 60 4 (AR) 22 APRIL 1988 MIL I TARY SPEC IF I CATI ON AMINE BONDING AGENT 1. SCOPE 1.1 Scope This specification covers the requirements, quality assurance provisions and packaging for the manufacture and acceptance-of one type of amine bonding agent (see
2、6.1). 2. APPLICABLE DOCUMENTS 2.1 - Government documents. O 2.1.1 .Specification, standards and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and standards (DoDISS)
3、specified in the solicitation form a part of this specification to the extent specified herein. SPECIFICATIONS . MILITARY MIL-A-48078 - Ammunition; Standard Quality Assurance Provisions, General Specification for STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attri
4、butes Beneficial comments (recommendations, additions, deletions) and any pertinent dat. which may be of use in improving this document should be addressed to: Commander, U.S. Army Armament,Munitions and Chemical Command, Attn. AMSMC-QA, Picatinny Arsenal, New Jersey 07806-5000 by using the self-add
5、ressed Standardite- tion Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by. letter. AMSC N/A 1 of 17 FSC 6810 DISTRIBLPTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted
6、 without license from IHS-,-,-MIL-A-70bOq b M 9999906 0122508 L1 = MIL-A-70604 (AR) . MIL-STD-129 - Marking for Shipment and Storage MIL-STD-286 - Propellants, Solid: Sampling, Examination and Testing MIL-STD-1168 - Lot Numbering of Ammunition MIL-STD-1218 - ACS Chemicals MIL-STD-1235 - Single and M
7、ultilevel continuous Sampling Procedures and Tables for Inspection by Attributes (Copies of specifications, standards, drawings, and publications required by manufacturers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the Contracti
8、ng Officer.) of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the of the DoDISS specified in the solicitation. The issues of documents which have not been adopted shall be those in effect on t
9、he date of the cited DoDISS. 2.2 Other publications. The following documents form a part AMERICAN SOCIETY FOR TESTING AND MATERlALS ASTM D2905 - Statement on Number of Specimens Required to Determine the Average Quality of a Textile Material D2196 - Rheological properties of Non-Newtonian Coatings,
10、Test . D3951 - Standard Practice for Commercial Packaging E168 - Recommended Practice for General Techniques in Infrared Quantitative Analysis. E300-73 - Recommended Practice for Sampling Industrial Chem i cals (Application for copies should be addressed to the American Society For Testing and Mater
11、ials, 1916 Race Street, Philadelphia, PA 19103.) the text of this specification and the references cited herein, the text of this specification shall take precedence. 2.3 Order of precedence. In the event of a conflict between 3. REQUIREMENTS 3.1 Composition. This amine bonding agent is one type of
12、reaction product of tetraethylenepentamine and acrylonitrile. material shall conform to the requirements given in Table I. The 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-P MIL-A- 70 60 4 (AR) TABLE I. Chemical and Physical Properties for Amine
13、 Bonding Agent Character is tic Requirement Max - Min. Applicable Test Paragraph Secondary Amine , eq/100g O. 9 1.2 4.5.1 Total Amine , eq/100g 1.1 1.5 4.5.2 Tertiary Amine, eq/100g 0.2 0.3 4.5.3 Ammonia, ppm - 500 4.5.4 Moisture, % - O. 85 4.5.5 Viscosity, 2S0cI CPS 500 1,000 4.5.6 3.2 Infrared Spe
14、ctrum. The IR spectrum of the sample shall contain the major peaks shown in Figure 1 when tested in accordance with 4.5.7. 3.3 First article inspection. This specification contains technical provisions for first article inspection. Requirements for the submission of first article samples by the cont
15、ractor shall be as specified in the contract. 3.4 Workmanship. The manufacturer shall implement procedures and controls to assure that the process and the product produced are not compromised by foreign materials and contaminants or any other conditions which may degrade the composition. Determinati
16、on of foreign materials shall be in accordance with 4.5.8. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as
17、otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set fo
18、rth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of section 3 and 5. The inspection set forth in this specification shall become a part of
19、 the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-A-70bOq 68 m 999990b OL225LO 2 m MIL-A-70604 (
20、AR) contractor of the responsibility of assuring that all products and supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of know defective material, either indicated or actual, nor does it c
21、ommit the Government to acceptance of defective material a 4.2 Classification of inspections. The inspection requirements specified here are classified as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (see 4,4) . 4.3. - Ferst article inspection, 4 a Provided by IH
22、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-A-70604 b8 W 7797706 OL2251L 4 .rl a ah O !i ai C 4 4 LI O Fr MIL-A-70604 (AR) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-A- 7 O 6 O 4 (AR) .4.3.1 S
23、ubmission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.3.2. The first article sample shall be ten (10) pounds of amine bonding agent. The sample shall be obtained from the Eirst production lot which has
24、 been produced by the contractor using the same production processes, procedures and equipment as will be used in fulfilling the contract. All materials shall be obtained from the same sources of supply as will be used in regular production. 4.3.2 Inspection to be performed. The sample will be subje
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILA706041988AMINEBONDINGAGENT 胺粘接剂 PDF
