1、25-f2- -. MIL-B-13 20 f D (ME) 12 August 1976 SUPERSEDING MIL-B-13207C (ME) 9 July 1970 MILITARY SPEGIFICATION BODY , VAN, VEHICLE-MOUNTED , GENERAL SPECIFICATION FOR This specification is approved for use by the Mobility Equipment Research and Development Command, Department of the Army, and is ava
2、ilable for use by all Departments and Agencies of the Department of Defense. 1. SCOPE. 1.1 Scope. This specification covers various sizes of intermodal container van bodies intended for the installation of a variety of operating equipment. The van bodies are modified refrigerated XSO (Inter national
3、 Organization for Standardization) containers which feature interior heating and air conditioning and utility electrical systems, transport by land and sea, in addition to wheeled vehicle mounted transport. capability between operation sgtes. may transport two van bodies, the first mounted on the st
4、raight transporter truck and the second mounted on the towed dolly converter and semitrailer. The van bodies are capable of international intermodal Optional truck and semitrailer mounti.ng provides travel When advantageous, a single driver 1.2 Classification. as specified (see 6.2) : The van bodies
5、 shall be of the following sizes, Modified Comercial IS0 Reefer Container Van Body: Size 10 - IS0 lD, 10-foot van body - MIL-B-13207/1, Size 20 - IS0 lC, 20-foot van body - MIL-B-13207/2. Size 30 - IS0 lB, 30-foot van body - MIL-B-13207/3. Size 40 - IS0 lA, 40-foot van body - MIL-B-13207/4. F / FSC
6、2510 THIS DOCUMENT CONTAINS !a PAGES. Licensed by Information Handling Services_ I MIL-B-13207D 25 9979706 038953i T B 2.1 Issues of documents, The following dacuments of the issue in effect on date of invitation for bids or request for proposal form a part of this specification to the extent specif
7、ied herein: I w-c-37 5 W- C-5 9 6 FI?- 11 5 TT-P-1757 MILITARY - Floor Covering Vinyl, Surface (Tile and Roll.), with Backing, - Circuit Breaker, Molded Case; Branch-Circuit and Service, - Connector, Plug, Electrical; Connector, Receptacle, Electrical, - Panel, Power Distribution, - Primer Coating,
8、Zinc Chromate, Low-Moisture-Senstiyiy, MIL-V-173 - Varnish, Moisture-and-Fungus- Resistant (for Treatment of Communications, Electronic, and Associated Equipment). MIL-P- - Plates, Identification, Instruction and Marking, Blank, MIL-T-704 - Treatment and Painttng of Materiel. BIIL-(2-3432 - Cable an
9、d Wire, Electrical CPower and Control; Semi-Flexible, Flexible and Extra Flexible, 300 and 600 Volts), MlL-W-5086 - Wire, Electric, Polyvinyl Chloride nsulated, Copper or Capper Alloy, MIL-An8423 - Air Transportability Requirements, General Specification2for, MIL-C-107 9 9 c Cloth, Coated, Cotton, V
10、in$. Coated, Pire and Mildew Redistant , MIL-F-21840 - Fastener Tapes, Hook and Pile, Synthetic, Licensed by Information Handling ServicesMIJpS-40626 MIL-E-46096 MIL-A-52767 MIL-C-52786 MIL- R- 5 2 813 STANDARDS FEDERAL FED. STD. No. 595 MILITARY MIL-STD-105 MIL-STD-12 9 MIL-STD-130 MIL-S TD-2 09 MI
11、L-S TD- 2 10 MIL- S TD-4 61 MIL-STD-642 MS75021 DRAWINGS TACOM 116 O 16 41 11601643 - Sign Kit, Vehicle Class-, - Enamel Lus.ter1ess a Quick Drying? Styrenated Alkyd Typel Salar Heat Reflecting. - Air Conditioner: Vertical and Horizontal, Compact; - Cover, Reel, Cotton Duck, - Reels, Hose and Cable,
12、 - Colors. - Sampling Procedures and Tables or Inspection by Attributes, - Marking for Shipment and Storage, - Identification Marking of US - Slinging and Tiedown Provisions Military Property, for Lifting and Tying Down Military Equipment a Equipment, Characteristics Requirements for Equipment . - I
13、dentification Marking of Combat and Tactical Transport Vehicles, - Connector, Receptable, Electrical - 12 Contact, Intervehicuar, 28 Volt, Waterproof, - Climatic Fxtremes for Military - Electromagnetic Interference - Cable Assy, Auxiliary, - Cable Assy, 3 Licensed by Information Handling ServicesMIL
14、-B-13Z07D 25 m 7Ob OL8753b 3 m MIL-B- 13 2 O 7D (?a) (Copies of specifications, standards, and drawings required by contractors in connection with specific procurement functions should he obtaned from the procuring activity or as directed by the contracting officer,) 2.2 Other publications. The foll
15、owing documents form a part of this . specification to the extent specified herein, Uness otherwise indicated, the issue n effect on date of invitation for bids or request for proposal shall apply. ASSOCIATION OF AMERICAN RAZLROADS (AAR) Rules Governing the Loading of Commodities on Open Top Cars, (
16、Application for copies should be addressed to the Association of American Railroads, 1920 L Street, NW, Washington, DC 20036,) AHERTCAN BURFAU OF SHIPPING (ABS) Guide for Certification of Cargo Containers. (Appllcation for copies should be addressed to the American Bureau of Shipping, 45 Broad Stree
17、t, New York, NY 20004,) ASSOCIATION OF HOIE APPLIANCE MANFACTURERS (AHAM) DH-2 - Dehumidifiers, Electric. (Applcation or copies should be addressed to the Association of Home Appliance Manufacturers, 20 North Wacker Drive, Chicago, UI 60606 a AMERICAN IRON AND STEEL INSTITUTE (AISI) Steel Products M
18、anual. (Application for copies should be addressed to the American Iron and Steel Znstitute, 150 East: 42nd Street, New York, NY 10017,) AMERICAN NATlONAL STANDARDS INSTITUTE (ANSI) S0 Recommendation No, 668 - Dimensions and Ratings of Freight IS0 Recommendation No, 1496 - Specifications and Tasting
19、 of Containers, Series 1 Freight Containers, 4 Licensed by Information Handling ServicesNational Electrical Code, C1, Al.19.2 - Mobile Vehicle Standards, C73.11 MH5 226.1 235.1 - Attachment Plqp and Receptacles, - Specifications for CaTgo Containers. - Safety Glazing Materiah fr Glazing Motor Vehicl
20、es Operating an Land Highways, - Industrial Accident Prevention Signs, Specifications for, (Application for copies should be addressed to the American National Standards Institute, Inc, 143Q Broadway, New York, Ny 3.0028.) AMERICAN PLyFIpOD ASSOCUTION CNA) US Product Standard PS 1, Plywood Design Sp
21、ecification Manual X215, (Application for copies should-be gddressed to the American Plywood AMERICAN SOCIETY OF MECHANICAL ENGINEERS (.ASME) Association, 1119 A Street, Tacoma, WA 9840-1.) Boiler and Pressure Vesse Code, Welding Qualifications, (Application for copies should be. addressed to the Am
22、erScan Society lOCU-7,1 AMERICAN SOCIETY FOR TESTIUG ANTl WTERWS sTM of Mechanical Engineers, 345 East 47th Street, New York, NY D 2, United States Postal Service, Flashngtonr DC 20260,) (Technical society and technical association specifications and standards are generally avatlable for reference f
23、rom librarles, are also distributed among technical groups and using Federal agencies, They 3. REQUIRFXENTS 3.1 Dscription. The van bodies shall be as specified herein and on the applicable specification sheet bee 1,2) van body (hereinafter called “van body“)_ shall include the; (1) basic van body s
24、tructure, c2) inteXior environmental control, system, c3) utility electrical and lighting system, (4) access.ories and components and, CS) the applicable transport vehicle, basic van body, contractor furnished environmental control system, ut2lity electrical and lighting system and the applicable tr
25、ansport yehcla? shall be the latest: commercial production models of the contractor and his sub contractors and shall have been marketed for a period of not less. than 1 year prior to openi-ng of the technical proposal or bid, except For product improvements which have been incorporated on comercial
26、 untts, bodies shall be constructed to function, withcmt malfunction! damage, or permanent deformation, with installed operation, equipment and machinery The complete vehicle-niounted The van body, separately covering the The van 9 Licensed by Information Handling ServicesMSL-B-13207D (ME) such as p
27、rinting pressas, process photographic cameras, laboratories, cryogenic plant sets, driver training devices, repair shop sets, office units, and similar applications , interior environment for correct function of both the equipment and personnel, when stationary at an operating site and shall provide
28、 continued protection for the equipment installed when the van bodies are being transported, Unless otherwise specified, the van bodies shall be mounted on a transport vehicle, As specified (see 6,2), the van bodies, in the manner and quantities specified, shall be vehicle mounted as follows and in
29、the applicable specification sheets: The van bodies shall provide controlled (a) IS0 sizes“m-m-m-“see 3.10 (b) Container, semitrailer mounted-see 3.11. Semitrailer without dolly converter- Table IV, a thru n. Full trailer with dolly converter- Table IV, a thru o. (1) (2) (c) Container, transport tru
30、ck mounted- see 3.12, When specified (see 6,2), van bodies shall be unmounted. 3,2 First article (preproduction model), The contractor shall furnish one van body for examination and testing within the time frame specified to prove prior to starting production that his production nethods and choice o
31、f design detail will produce van bodies that comply with the requirements of this specification. tests shall be those specified in Section 4 and shall be subject to surveillance and approval by the Government (see 6.3) , When specified (see 6,2), the Government will conduct any or all of the preprod
32、uction examinations and tests, as specified (see 6.2) , Examination and 3.3 Initial production, When specified (see 6.2), the contractor shall furnish to the Government one or more van bodies for inspection as speciFied in 4.4, 3.4 Material. Material shall be as specified herein. A11 material shall
33、be new and unused. Material not specified shall be selected by the contractor as being compatible with the intended uee in accordance with .the engineering standards o the truck body and freight container industry and as set forth in the publications of the American Society JO Licensed by Informatio
34、n Handling Servicesfor Testing and Materials, Society of Automotive Engineers including SAE Handbook, Truck-Trailer Manufacturers Association, International Organization for Standardization, American National Standards institute, and in Machinerys Handbook. products furnished shall not exceed 8 cale
35、ndar quarters in age from date of cure of the rubber to date of acceptance of the van bodfes by the Government. and SAE Standards. Maximum practical usa shall be made of inter- changeable hardware and fastening devices and a minimum number of types and sizes of bolts, capscrews, nuts, washers, and s
36、imilar common (standard) parts in accordance with SAE J37Q and ,3371. Unless 0thems.e Specified herein, rubber Threaded parts shall be in accordance with IF1 Standards 3.4.1 Contact of dissimilar metais. Contact, galvanic and electrolytic action between dissimilar metals, as defined in ML-T-704, sha
37、ll be prevented by the application of zinc chromate primer conformng to TT-P-1757 to each of the metal surfaces or by insulation of one surface, from the other surface by application of an elastomer gasket, electrical tape, or other effective means, preventing any direct contact. The separation of t
38、he surfaces shall be not less than 2 mils. compounds shall not be used nor shall tape be used of the type that bunches between the metal surfaces during hole drilling operations. Asphaltic-type 3.4.2 Noise absorption material. man specified (see 6.2), and when required by the construction methods se
39、lected by the contractor to.meet the noise level limit, the van body interior shall be lined with acoustic absorption materials. The material selected for ceiling, walls, front end, and larger rear 2/3 door (excluding personnel and other doom) shall, have a noise reduction coefficient (WC) value of
40、at least Q.75, F 3.4.3 Corrosion. Ferrous components and parts o the basic van body, if furnished, shall be of corrosion-resistant steel or protected from corrosion by application marine type of plating. 3.5 Environmental conditions. 3.5.1 Operational temperatures. The van bodies shall not be damage
41、d during operation and transport in any ambient air temperature between minus 40 F and plus 120 F. 3.5.2 The van bodies shall not leak water inta the interior of the van bodies when exposed to rain ranging from a drizzle to a heavy rain of 1/4 gallon per minute per square foot of wetted surface impi
42、nging on the van body with a 30 mph wind and when transported on a TOFC railroad car during rain conditions, the precipitation, the equipment shall operate as specified herein. During and after 11 Licensed by Information Handling ServicesMIL-B-13207D (ME) 3.5.3 Storage, When in outside stor,age, the
43、 van bodies shall with- stand climatic extremes as specified in MIL-STD-210 without deterloraton that may cause allure of the van bodies or of any component, 3.6 Safety. The safety characteristics of the van bodies shall. meet the following minimum requirements: Conform to DOT Federal Motor Vehicle
44、Safety Standards (WSS), 49CPR567 and 571. Conform to DOT Federal Motor Carrier Safety Regulations (FIESR), 49CFR325, 390, and 393. Conform to the California Vehicle Code. Conform to DOL OSHA requirements, 29CFH.926, based on an 8-hour shift . Incorporate human factors engineering characteristics or
45、use and operation by personnel ranging from the small man, clothed, through the large man, arctic clothed, per SAE J833 and 5925, Provide all walk, step, and handhold components per Result in furnishing material and componenta having a correct safety factor. Provide correct guarding, enclosing, and
46、insulating features for exposed components and systems, which are inherently hazardous or have high temperatures, high pressures, or high electrical voltage. Eliminate nonfunctional sharp edges, projecting points, and excessive lengths of fasteners. SAE 3185. 3,7 Ease of maintenance. All major assem
47、blies and installed attachments shall be accessible for maintenance, repair, and replacement without the removal. of other major assemblies and installed attachmenta. Covers or plates which must be removed for component adjustment, repair, replacement, or maintenance shall be equipped with removable
48、 fasteners. The configuration of the van bodies shall provide maximum accaasibility for removal of components. Where incorrect installation of an item could cause malfunction af that item or of the system in which it is installed, an unsymnetxical mounting means shall be provided or the mating parts
49、 shall be dowled or matchmarked. Ease of maintenance provisions shall incorporate features insuring operating tool and lubricant component clearances and shall facilitate maintenance and servicing operations. incorporated to facilitate repair and refabricaton of the van body to original weather tightness and insulation requirements when vehicle transport and intermodal transport damage occurs. Ease of maintenance considerations sha
