1、MIL-C-40131C 84 7777906 0370825 7 W MIL-C-4 013 1C 15 September 1986 SUPERSEDING MIL-C -401 3 1B 11 June 1968 MILITARY SPECIFICATION COVER, WATER CANTEEN, INSULATED, COTTON DUCK This specification is approved for use by all Departments and Agencies of the Department of Defense. 1- SCOPE 1.1 Scope. T
2、his document covers one type and size of canteen cover fabricated of Olive Drab cotton duck, tape, and webbing and attached hardware. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Documents. The following documents form a part of this document to the extent specified herein. Unless otherwi
3、se Specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL A-A-2 03 - Paper, Kraft, Untreated V-T-285 - Thread, Polyester . Benefi
4、cial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to U. S. Army Nat ick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the self -addressed Standardization Document Improvemen
5、t Proposal (DD Form 1426) appearing at the end of this document or by. letter AMSC N/A FSC 8465 1 DISTRIBUTION STATEMENII- A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS 37 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
6、from IHS-,-,-MIL -C -4 O1 3 1 C ccc-c-4 19 CC C -D -9 5 O DDD -L-2 O PPP -B -6 3 6 MIL I TARY MIL -W -5 3 O MIL -H-9 8 90 MIL-F-10884 MIL-L-3 5078 MIL-C -401 24 MIL-C -401 26 MIL-T-43566 STANDARDS FEDERAL FED -STD -7 51 - Cloth, Duck, Cotton, Unbleached, Plied-Yarns Army - Dyeing and Aftertreating P
7、rocesses for Cotton - Label : - Boxes, Shipping, Fiberboard and Numbered Cloths (General Use) for Clothing, Equipage, and Tentage, - Webbing, Textile, Cotton, General. Purpose, - Hardware, Individual Load Carrying Equipment: - Fasteners, Snap - Loads, Unit : Preparation of Semiperishable Subsistence
8、 Items; Clothing, Personal Equipment and Equipage ; General Specification For Steel Without Cup and Cover Natural or in Colors and Hardware, Miscellaneous - Canteen, Water, Insulated, Corrosion-Resisting - Cup, Water Canteen (for Insulated Canteen) - Tape, Textile, Cotton or Polyester, General. Purp
9、ose, Natural or in Colors - Stitches, Seams, and Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by At tributes MIL -S TD -1 2 9 - Marking for Shipment and Storage MIL-STD -147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets
10、DRAWING U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2 -2 -21 1 - Cover, Water Canteen, Insulated, Cotton Duck 2 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-qO23LC 84 W 9799706 O390827 O W MIL -C -4 O1 3 1 C (Copies of d
11、ocuments required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this document to the extent specified herein. Unless otherwi
12、se specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the dat
13、e of the solicitation AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASIM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical assoc
14、iation documents are generally available for reference from libraries. technical groups and using Federal agencies. ) They are also distributed among 8 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document sha
15、ll take precedence. applicable laws and regulations unless a specific exemption has been obtained. Nothing in this document, however, shall supersede 3. REQUIREMENTS 3.1 Samples. 3.1.1 Standard sample. The cotton duck cloth shall match the standard sample for shade and shall be equal to or better th
16、an the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3). 3.1.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). f 3.2 Materials. Recycled material
17、 may be used (see 6.5). 3.2.1 Cloth, duck, cotton. The cloth, before finishing, shall be No. 6, hard texture, conforming to type I of CCC-C-419. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4 O1 31C 3.2.1.1 Color and treatment. The cloth s
18、hall be dyed Olive Drab 7 to match the standard sample (see 6.3) and shall conform to type I, class B of CCC-D-950 3.2.2 Tape, cotton. The tape shall be dyed Olive Drab 7 to match the standard sample (see 6.3) and shall conform to type I, class 4, 3/4 inch width of MIL-T-43566 I 3.2.3 Webbing, cotto
19、n. The webbing shall be dyed Olive Drab 7 to match the standard sample (see 6.3) and shall conform to type IIb, class 4, 2 1/4 L inch width of MIL-W-530. 3.2.4 Thread, polyester. The polyester thread shall be type I, class 1, subclass B of V-T-285. The thread sizes shall be as follows: a* For all st
20、itching, except binding and overedge stitching, use b. For binding and overedge stitching, use size E. size FF. 3.2.4.1 Color. The thread shall be dyed shade S-1 (Cable No. 66022) and shall show fastness to chlorine bleaching equal to or better than the standard sample (see 6.3). If no standard samp
21、le is available, the thread shall show “good“ fastness to chlorine bleaching. 3.2.5 Fasteners, snap The snap fasteners shall conform to style 2, finish 2 of MIL-F-10884. The female components shall be socket and size 1 or 2, 24-line button, and the male components shall be stud and size 1 or 2 eyele
22、t. 3.2.6 Keepers, with slide. The keepers shall be steel, black in color, and shall conform to type X of MIL-I-9890. 3.3 Construction. The construction shall conform in.all respects to Drawing 2-2-211 and as specified herein. 3.3.1 Stitches. seams. and stitchiws. 3.3.1.1 Type of stitching. All stitc
23、hing shall conform to FED-STD-751, as follows: a. For all stitching except overedge stitching on reinforcement - Type 301, 6 to 8 stitches per inch. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-C-40L3LC 84 M 797770b 0390829 4 I - MIL-C-40131
24、C b. For overedge stitching on reinforcement - Type 304, 10 to 14 stitches per inch; or type 502 or 503, 6 to 10 stitches per inch. 3.3.1.1.1 Automatic stitching. Any of the stitching operations cited in this document may be performed with an automatic machine provided that the requirements for stit
25、ch pattern, stitches per inch, size and types of thread are met, and that at least three tying, overlapping, or back stitches are used to secure the ends of stitching. 3.3.1.1.2 Lubrication of thread. There shall be no lubrication of the thread prior to or during sewing (see 4.4.1.1). 3.3.1.1.3 Type
26、 301 stitching. Thread breaks in stitching shall be overstitched not less than 1 inch back of the break. Ends of all stitching shall be backstitched or backtacked not less than 1 inch except where ends are caught in other seams and stitching. Thread tensions shall be maintained so that there will be
27、 no loose or tight stitching and the lock will be embedded in the sewn materials. 3.3.1.1.4 veredge stitching Thread breaks and overedge stitching shall - be overstitched not less than 3/4 inch at each break. Thread tension shall be maintained so that there will be no loose stitching. 3.3.1.2 Trimmi
28、ng. All thread ends shall be trimmed. 3.3.2 Setting of the metallic snap fasteners. Holes punched before inserting the male or female part of the fasteners shall be smaller than the outside diameter of the fastener tubes so that the tubes must be forced through the holes. The fasteners shall be secu
29、rely clinched without cutting the material. 3.4 Marking. The identification marking shall be applied in the location shown on Drawing 2-2-211 and shall conform to type IV, class 5 of DDD-L-20. The letters “US“ shall be applied in the size of characters and in the location indicated on Drawing 2-2-21
30、1 and shall conform to type IV, class 9 of DDD-L-20. Fastness of class 9 marking shall be as specified for class 5 marking . 3.5 Workmanship. The covers shall conform to the quality of product established by this document, and the occurrence of defects shall not exceed the applicable acceptable qual
31、ity levels. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - -. - - I - - MIL-C-4OL3LC 84 7777906 0370830 O MIL -4 O1 3 1 C 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchas
32、e order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified
33、 herein, unless disapproved by the Goverment. The Government reserves the right to perform any of the inspections set forth in this document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. if 4.1.1 Responsibility for compliance. All ite
34、ms must meet all requirements of sections 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. absence of any inspection requirements in the document shall not relieve the contractor of the responsibility of assuring
35、that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The Sampling in quality conformance does not authorize s
36、ubmission of * 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible for assuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shaL1 be made at any
37、point,.or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. 4.1.3 Certificates of compliance. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certificati
38、on. 4.2 Classif Abrasion mark Hardware Snap fastener Keeper Seams and stitching Open seams Broken or malformed, failing to serve intended purpose; corroded area, burr, or sharp edge Finish omitted or not as specified Finish defects (i.e., objectionable orange peel, wrinkle, drop, streak, thin film,
39、or no film) specified purpose Not attached or assembled as Misplaced, failing to serve intended Not functioning properly, failing to effect a secure closure or to open freely Slide portion of keeper jams, failing to effect a secure closure Major Minor AB X X X X X X X More than 1 inch X More than 1/
40、2 inch, but not more than 1/2 inch or less 1 inch 8 X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40131C TABLE I. End item visual defects - Continued t MIL-C-40L3LC 84 m 7797906 0370833 b m b Examine Defect Classification Seams and stitch
41、ing - NOTE : continued Raw edge (on edge required to be finished) NOTE : Run-off (see open seams) Seam and stitch type Stitch tension Stitches per inch A seam shall be classified as open when one or more stitches joining a seam are broken, or when two or more skipped stitches or run-Offs occur. On d
42、ouble stitched seams, a seam shall be considered open when either one or both sides of the seam are open. More than 1/2 inch when securely caught in stitching Raw edges not securely caught in stitching shall be classified as open seams. Wrong seam or stitch type Loose, resulting in a loosely exposed
43、 bobbin or top thread; tight, resulting in excessive puckering of fabric n seam One stitch less than minimum Two or more stitches less than One or more stitches in excess specified minimum specified of maximum specified 9 Major Minor AB X X X X X X Provided by IHSNot for ResaleNo reproduction or net
44、working permitted without license from IHS-,-,-MIL -C -4 O1 3 1 C TABLE I. End item visual defects - Continued _I.-p - _._I_I_- MIL-C-qOL3LC 84 W 7777706 0370834 - Examine , Defect Classification Major Minor n Seams and stitching - continued NOTE: Variation in the number of stitches per inch caused
45、by the operator speeding up the machine and pulling the fabric in order to sew over heavy places or heavy seams, or in turning carners shall be classified as follows: a. Within the minor B defect classification - no defect. b. Within the minor A defect classification - minor B defect. Stitching marg
46、ins Not as specified or stitching gage End of stitching Not backstitched or secured (not held down Backstitched less than 1 inch by other stitching or turned under in a hem) Thread breaks Backstitched less than 1 inch (type 301) Overstitched less than 3/4 inch (overedge stitching) Stitching NOTE: Th
47、read break not backstitched ,or overstitched shall be classified as an open seam. One or more rows of required stitching omitted (except on box stitching) X x X X X X 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. - MIL-C-4013lC 84 7977706 0370
48、835 T MIL-C-40131C TABLE I. End item visual defects - Continued Examine Defect C las s i f ica tion Seams and stitching - continued Box stitching Components and assembly Binding Reinforcement s “ B“ and “C“ Reinforcement “D“ Cleanness Marking Two or more rows of stitching One row of ititching omitte
49、d . omitted Any component part or required operation omitted or not as specified (unless otherwise classified herein) Needle chews - Mend or .darn Improperly or loosely applied, badly puckered Exposed edge of reinforcements not selvage edge or not turned under Cut ends of webbing not overedge stitched . . . Grease or oil stains clearly noticeable, -thread ends not -. trimmed - throughout Omitted, illegible, -incorr
