1、t _I .- -m- UIL-C-YO602B 73 7777706 02Y3234 7 = 1 MIL-c- 1285 Walt Whitman Road, Melville, LI., New York 11746, or i655 Scott Boulevard, Santa Clara, California 9505Q) NATIONAL SANII?A!iION FOUNDATION (NSF) 4 Standard No. 8: Commercial Powered Food Preparation Equipment (1.965) Seal of Approval List
2、ing ,of Food Service Equipnent (Application for copies should be addressed to the National Sanitation Foundation, P. O. 3ox 1468 Ann Arbor, Michigan 48104.) AMERICAN SOCIETY FQR TESTING AND MATERLALS (AEZM) ASTM Standard Ai67-63 : Corrosion-Resi sting Chromium-Nickel Steel Plate, and Strip AS934 Sta
3、ndard Ai76-63: Corrosion-Resisting Chromium Steel Plate, Sheet, and Strip %?sting and Materials, 1916 Race St., Philadelphia, Pa. 19106.) (Application for copies should be addressed to the American Society for 3. F3QUIRiWNTS 3.1 Preproduction sample.- Unless otherwise specified (see 6.2), before pro
4、duction is commenced, a sample cookie-cutting machine shall be submitted or made available to the contracting officer or his authorized representative for approval in accordance with 4.2. sample authorizes the commencement of production, but does not relieve the supplier of responsibility for compli
5、ance with all applicable provisions of this specification. The preproduction sample shall be manufactured in the same facilities to be used for the manufacture of the production items. The approval of the preproduction I .2 I/. . I. . Provided by IHSNot for ResaleNo reproduction or networking permit
6、ted without license from IHS-,-,-MIL-C-40b02B 73 m 777770b 024L23b O m 3.2 Standard product.- Cookie-cutting machine delivered under this specification shall be the manufacturers current standard product, except for any changes necessary to comply with specification requirements. 3.3 Standards compl
7、iance.- 3.3.1 Safety standard.- The cookie-cutting machine shall conform to the applicable requirements of Standard UL73. 3.3.1.1 Certification.- Prior to approval of the preproduction sample, if one is submitted, or prior to approval of the first shipment, the supplier shall submit satisfactory evi
8、dence to the contracting officer or his authorized representative that the cookie-cutting machines he proposes to furnish under this specification meet the applicable requirements of standard UL 73. the UL label, listing in the UL “Electrical Appliance and Utilization Equip- ment List“ or a certifie
9、d test report from a recognized independent testing laboratory, acceptable to the Goverment, indicating that the cookie-cutting machine offered hac been tested and conforms to the applicable requirements Acceptable evidence of meeting the requirements of the UL shall be of UL 73. the applicable requ
10、irements of NSF Standard No. 8. 3.3.2 Sanitation standard.- The cookie-cutting machine shall conform to I 3.3.2.1 Certification.- Prior to the approval of the preproduction sample, if one is Submitted, or prior to approval of the first shipment, the supplier shall submit satisfactory evidence to the
11、 contracting officer or his authorized representative that the cookie-cutting machine he proposes to furnish under this specification meets the applicable requirements of NSF Standard No. 8. standard shall be an NSF seal, a listing in the NSF “Seal of Approval Listing of Food Service Equipment“ or a
12、 certified test report from a recognized independent testing laboratory acceptable to the Government, indicating that the cookie-cutting machine offered has been tested and conforms to the applicable requirements of NSF Standard No. 8. Acceptable evidence of meeting the requirements of this 3.4 Mate
13、rials.- Materials not definitely specified shall be of the quality normally used by the manufacturer in his standard commercial cookie- cutting machine. 3.4.1 Corrosion-resisting steel. - Corrosion-resisting steel used for food-contact surfaces shall conform to any of the type 300 series specified i
14、n ASTM Ai67-63 with at least For all other surfaces, the chemical compositions of any of the type 300 series of ASTM 167-63 or any of the type 400 series of ASTM 176-63, shall be acceptable. 18 per cent chromium and 8 per cent nickel. 3.4.2. Copper-nickel alloy. - Copper-nickel alloy shall contain 2
15、2 percent nickel, minimum, and 65 percent copper, minimum. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. . MIL-C-GOb02B 73 W 7777706 0243237 2 W- -i - _- . 3.4.3 Auminum alloy.- Almnum alloy shall be almag 35, as specified in QQ-A-601. 3.5 Desi
16、gn.- The cookie-cutting machine shall consist of a dough hopper, chute, feed-rolls with scrapers, die-plate, cutter fingers and cut-off wires above an automatic, double V-belt-type pan conveyor, with pan guides aljustable for i7 inch to 19 inch pans. tension. The machine shall be adjustable for cook
17、ie thickness and spacing on the pan, shall have a variable speed drive of at least 35 to 70 strokes per minute and shall automatically operate to produce cookies of uniform in 4.8.1 and 4.8.2. dies and to permit normal repair and maintenance of components without major disassembly of the machine. ma
18、chine shall be designed for operation on a nominal 120-volt, single-phase, 60-cycie, alternating current system. following overall dimensions: 72 inches long by 36 inches wide by 60 inches Hgh. V-belts shall be adjustable in I - size and shape using the dies specified in 3.6.3, when tested as specif
19、ied Provisions shall be made to facilitate the changing of Unless otherwise specified (see 6.2), the The machine shall not exceed the 3.6 Construction.- , 3.6.1 Hopper, chute, shafts and table-top.- The hopper, chute, feed-roll shafts and table-top shall be made from corrosion-resisting steel specif
20、ied in 3.4.1. 3.6.2 Feed rolls.- Feed rolls shall be made of corrosion-resisting steel specified in 3.4.1, or aluminum alloy Specified in 3.4.3. 3.6.3 Feed-roll bearings and dies.- Feed-roll bearings and dies shall be Each cookie- made from auminum alloy specified in 3.4.3, corrosion-resisting steel
21、 specified in 3.4.1, or copper-nickel alloy specified in 3.4.2. cutting machine shall be furnished with following dies: I Quantity 1 1 1 1 With 4 round openings each 2-1/9 L inches in diameter. With 4 scalloped round openings each 2-1/2 inches in With 4 rectangular openings each 1-1/4 by 2-1/4 inche
22、s. With 6 round openings each 1-inch in diameter. diameter. 3.6.4 Casters.- Each cookie cutting machine shall be equipped with two rigid casters on one end and two swivel casters on the other end. casters shail have ball or roller bearings at the axle. shall have rubber-tired wheels 4 to 5 inches in
23、 diameter, and pressure lubricating fittings. Rigid All casters Swivel casters .shall have ball or roller bearings at both axle and swivel. 4 marred surfaces, dents, punctures,-fractures, rough edges, burrs, slivers. All welds shall be smooth and uniform, completely fused, without undercuts, cracks
24、burnholes or fractures. All fasteners shall be tight. No component shall be misslng, malformed. and aligned. All components shall be carefully assembled, properly adjusted -. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ - _- - .- . MIL-C-40602
25、B 73 9999906 0243237 b W 4 s HILC-40602B( GL) . 4. WAL!F ASSWWCE PROVISIONS 4.1 Responsibility for inspection.- Unless otherwise specified in the contract or purchase order, the supplier Is responsible for the perfom- ance of ail Inspection requirements as specified herein. otherwise specified in th
26、e contract or order, the supplier may use his own or my other facilities suitable for the performance of the in- spection requirements specified herein, unless disapproved by the Govern- ment. The Government reserves the right to perform any of the inspec- tions set forth in the specification where
27、such inspections are deemed necessary to 8ssure supplies Except as . * and services conform to prescribed requirements. 4.2 Preproduction sample inspection. - When a preproduction sample is required, it shall be inspected for defects listed in table I, dimensions specified and shall be tested as spe
28、cified in 4.8.1 and 4.8.2, and 4.8.3 when applicable. 4.3 Inspection.- Sampling for inspection shall be performed in accord- ance with MIL-STD-105, except where otherwise indicated hereinafter. 4.3.1 Component and material inspection.- In accordance with 4.1 above, camponents and materials shall be
29、inspected and tested in accordance with all the requirements of referenced specifications and s;tandards unless otherwise excluded, amended, modified or qualified in this specification or applicable purchase document. 4.3.1.1 Chemical analysis.- Copper-nickel alloy shall be tested for chemical analy
30、sis in accordance with method 111.1 of Fed. Test Method Std No. i51 to detexmine compliance with requirements specified in 3.4.2. 4.4 End item inspection.- The inspection lot shall be the number of cookie-cutting machines offered for delivery at one time. for this Inspection shall be one completely
31、assembled cookie-cutting machine. The sample unit 4.4.1 Visual examination.- Examination of the end item shall be made for defects in table I. The inspection level shall be II with an-accept- able quality level (AQL) of 2.5 for major defects and 6.5 for total defects, expressed in terms of defects p
32、er hundred units. TABLE I.- Classification of defects Classification Examine Defect Major Minor Finish - Not finished as specified X Part permanently soiled or corroded Finished surfaces not smooth X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
33、MIL-C-40602B( GL) TABLE I.- Classification of Defects (contd) C1 a s si f i c at i on Defect Major Minor of production, shall be used as a model for all production units. with 3.6.10 The supplir shall fmnish the contracting officer, Upon approval of the report by the contracting as applicable, 5. PR
34、EPARATION FOR TIELIVERY 5.1 Preservation and packaging.- Preservation and packaging shall be level A or C as specified (see 6.2). 5.1.1 Level A.- Each cookie-cutting machine and accessories shall be preserved and packaged in accordance with the applicable requirements for level A of MILB-2316. 5.1.2
35、 Level C.- Each cookie-cutting machine and accessories shall be preserved and pacbaged in accordance with the industrys practice. 5.2 Packing.- 5.2.1 Level A.- Each cookie-cutting machine and accessories, preserved Packing shall be level A, B, or C as specified (see 6.2), and packaged as specified i
36、n 5.1, shall be packed in accordance with the applicable requirements for level A of MIL-B-2316. e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-40602B 73 m 977970b 0241243 m MIL-C-h0602B( GL) 5.2.2 Level B.- Each cookie-cutting machine and a
37、ccessories, preserved and packaged as specified in 5.1, shall be packed in accordance applicable requirements of level B of 1-2316. ,Each cookie-cutting machine and accessories, packed in an open type crate, shall be completely covered with a polyethylene film shroud reaching down on all sides to wi
38、thin 1-inch of the base of the machine. be 0.003 inch thick conforming to type II of L-P-378. with the The polyethylene film shall 5.2.3 Level C.- Cookie-cutting machine and accessories, preserved and packaged as specified in 5.1, shall be packed in a manner to insure carrier acceptance and safe del
39、ivery at destination at the lowest transportation rate for such supplies. Containers shall be in accordance with rules or regulations of carriers applicable to the mode of transportation. 5.3 Marking.- In addition to any special marking required by the contract or order, interior packages and shippi
40、ng containers shall be marked in accordance with MIL-STD-129. 6. NOTES 6.1 Intended use. - The cookie-cutting machine covered by this specifica- tion is intended for use in Military bakeries to cut dough automatically into various cookie-shapes, using dies furnished with the machine. 6.2 Ordering da
41、ta. - Procurement documents should specify the following: (a) (b) (c) (d) (e) (f) Title, number, and date of this specification. When preproduction sample is not required (see 3.1). Electrical characteristics, if other than specified (see 3.5). Whether machines shall be equipped to insure electromag
42、netic Manual contents and distribution of additional manuals (see 3.7). Selection of applicable levels of preservation, packaging and compatibility (see 3.6.10, 4.8.3 and 6.3). packing (see 5.1 and 5.2). 6.3 Electromagnetic compatibility.- The contracting officer should sub- mit a copy of the repgrt
43、 required in 4.8.3, if applicable, to the Command- ing General, U. S. Ardy Electronics Command, AWN: Monmouth, New Jersey, for approval. AMSEL-RD-GF, Fort 6.4 Asterisks were not. used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Custodians: Army - GL i I Review activities : j: Army - EL, m; ME Preparing activity: Project No. 732O-AO98 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
