1、MIL-C-4LI002A 42 7797706 02337b5 7 - s - /s -29 MIL-C-44002A( GL) SUPERSEDING MIL-C-44002(GL) 27 July 1979 19 June 1985 MILITARY SPECIFICATION COVERALLS , PROTECTIVEy TOXICOLOGICAL AGENTS, FIRE RESISTANT: (POTMC) This specification is approved for use by the Natick Research and Development Command,
2、Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification shall be of one type in the following sizes ! as specified (see 6.2). Schedule of Sizes Small Medium Large X-La r g e XX- La r g e 2. APPLICABLE DOCUM
3、ENTS 2.1 Issue of documents. The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use
4、 in improving this document should be addressed to: U.S. Army Natick Research and Development Command, Natick, M, 01760, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 4240 7 THIS DOCUMENT CONTAINS s#-
5、PAGES -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL V-F-106 UU-P-268 DDD-L-20 PPP-B-636 MILITARY MIL-W-5664 MIL-F-10884 MIL-F-21840 MI L-T-4 36 36 MIL-W-43685 MIL-T-43709 STANDARDS FEDERAL FED-STD-191 FED-STD-751 MILITARY
6、MIL-STD-105 MIL-STD-129 MIL-C-qq002A Y2 947740b 02337bb O = MIL-C-44002A( GL) - Fastener, Slide, fnterlocking - Paper, Kraft, Untreated, Wrapping - - Boxes, Shipping, Fiberboard Label; For Clothing, Equipage and Tentage (General Use) 1 - Webbing, Textile, Elastic, Cotton - Fastener, Snap - Fastener
7、Tapes, Hook and Pile, Synthetic - Thread, Aramid - Webbing, Tape, Textile, Aramid Fiber - Tape, Textile, Aramid i * - Textile Text Methods - Stitches, Seams and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage Attributes (Copies of specifications, stan
8、dards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer . ) LAWS AND REGULATIONS US Postal Service Manual (Copies of the manual may be obtained from the Superi
9、ntendent of Documents, US Government Printing Off ice, Washington, DC 20402.) 2.2 other publications. Unless otherwise specified, the following documents o the issue in effect on date of Invitation for Bids or request for proposals, form a part of this document to the extent specified herein. 2 Prov
10、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44002A 42 7797906 0233767 2 MI L-C-44002A( GL) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D-3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the
11、American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. technical groups and using Federal agencies. ) They are also distributed among 3. REQUIREMENTS 3.1 Guide
12、 sample. Guide samples, when furnished, are solely for guidances and information to the contractor (see 6.3). may appear in the sample, in which case the specification shall govern. Variation from the specification 3.1.1 First article. When specified, a sample shall be subjected to first article ins
13、pection (see 4.1.2, 6.2, and 6.6). 3.2 Materials. 3.2.1 Basic material. The basic material shall be aramid twill cloth, natural color, 6.23 to 7.23 oz/yd2 conforming to Putnam Mills Style 650 or equal (see 6.7). 3.2.2 Fastener tapes. The hook and pile fastener tapes for front neck closure and waist
14、adjustment, shall be 1-inch wide hook and pile, White 3055, conforming to type II, class 2 of MIL-F-21840. 3.2.3 Slide fasteners. The slide fasteners shall be brass, with a black chemical finish and conform to V-F-106. The material for the tapes shall be an aramid tape 3/4-inch wide, Olive Drab Shad
15、e S, Cable No. 66519, Air Force Gray No. 468 or natural, and shall show fastness to laundering. Thongs are required on all slide fasteners. The finished length of the thongs shall be measured from the top of the loop to the end of the thong. 3.2.3.1 Front opening. The slide fastener for the front op
16、ening- shall conform to type I, style 15, with long tab pull, size M. The lengths for the various sizes shall comply with operation 25.b. The thongs shall finish 3-1/2 to 4 inches long. Thongs are required on both pull tabs. 3.2.3.2 Front lateral openings. The slide fasteners for the front lateral o
17、penings shall conform to type IV, style 8, with short tab pull, size M, 16 inches long. The thongs shall finish 2-1/4 to 2-3/4 inches in length. 3.2.3.3 Thong tape. The tape for slide fastener thongs shall conform to MIL-T-43709. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted
18、 without license from IHS-,-,-MIL-C-44002A 42 m 949990b 0233768 Y W MIL-C-44002A( GL) 3.2.4 Elastic webbing. The elastic webbing for the back waist shall be cotton, 1 inch wide, natural, conforming to class 1 of MIL-W-5664 or commercial equivalent (see 6.4). - - 3.2.5 Snap fastener. The snap fastene
19、rs for right and left front openings, and bottom of sleeves and legs shall conform to style 2, finish 2 of MIL-F-10884. female component shall be the socket with a 24 line size, size 1 button. The male component shall be the stud with size 1 eyelet and the 3,2,6 Webbing, aramid. The aramid webbing u
20、sed to attach socket portions of snap fastener on sleeve and leg bottoms shall conform to type II of MIL-W- 43685 except that the color shall be natural. . 3.2.7 Thread, aramid. The aramid thread for seaming and stitching shall be white or natural, and shall conform to size B and E of MIL-T-43636. .
21、 3,2,8 Labels, Each coverall shall have a combination size and identification label and an instruction label conforming to type VI of DDD-L- 20. Fastness to laundering requirements of DDD-L-20 shall apply. 3.2.8.1 Combination size and identification label, The combination size and identification lab
22、el shall conform to classes 1 and 2 combined, 3.2.8.2 Instruction label, The instruction label shall conform to class 3 and shall contain the following information: COVERALLS, PROTECTIVE, TOXICOLOGICAL AGENTS, FIRE RESISTANT: (POTMC) 1. Use an instructed in manual on operation and maintenance of Pro
23、tective Outfit, Toxicological, Microclimate Controlled. 2. May be hand or machine washed using soap or detergent and warm water, Hang or tumble dry. During laundering and drying, engage all fasteners (hook and pile, snap and slide), 3, Coverall is of low flammability. No other special flame resistan
24、t treatment is required. 4, Lubricate slide fasteners with zipper lubricant NSN 9150-01-112-9412, CAUT IONS a, The system contains ferrous metals. Caution should be exercised when operating in the vicinity of items having magnetic properties. 4 Provided by IHSNot for ResaleNo reproduction or network
25、ing permitted without license from IHS-,-,-MIL-C-44002A L12 W 797790b 0233769 b W MIL-C-44002A( GL) b. The suit and its components must be decontaminated before doffing . c. The suit system must not be treated by any of the following decontaminating agents: DANC, DS2, CAUSTIC SODA, BOILING WATER. DO
26、 NOT REMOVE THIS LABEL 3.3 Design. The coverall has a front opening with slide fastener having multiple sliders; two front lateral openings with separating slide fastener; leg and sleeve abrasion patches; atropine pocket on left sleeve; neck yoke; elastic waist; openings on left and right front and
27、back; and snap fastener tabs at bottom of legs and sleeves. extends from top of front to 2 inches below waist seam on back. The slide fastener at front lateral openings extend from top of neck yoke to the openings on left and right front. The slide fastener at front opening All sliders have thongs.
28、3.4 Figure. Figure is furnished for information purposes only. To the extent of any inconsistencies between the Specification and the figure, the specification shall govern. 3.5 Patterns. Standard patterns which provide an allowance of 3/8 inch for all seams, unless otherwise indicated, will be furn
29、ished by the Government. The standard patterns shall not be altered in any way and.are to be used for cutting contractors working patterns. identical to the standard patterns. The working patterns shall be 3.5.1 Pattern parts. The component parts of the coveralls shall be cut from the specified mate
30、rials in accordance with pattern parts indicated in table I. TABLE I. List of pattern parts Component Pattern nomenclature Cut parts Basic material (see 3.2.1) Upper back Back leg Right front Left front Front facing Under sleeve Outer sleeve Leg abrasion patch Sleeve abrasion patch Adjustment s trap
31、 Adjustment strap (tunnel) Atropine pocket front 5 1 2 1 1 2 2 2 2 2 2 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44002A 42 797770b 0233770 2 TABLE I. List of pattern parts (contd) - - Component Pattern nomenclature Cut parts Basic mat
32、erial (see 3,2,1) (cont d) Atropine pocket back Neck yoke Facing for back opening Facing for right front opening Facing for left front opening Front hardware opening tab SHAPERS Right front opening (with stitch line) Left front opening (with stitch line) Back opening (with stitch line) 3.6 Construct
33、ion, 3.6.1 Stitches, seams, and stitching. Stitch, seam and stitching types specified in table II shall conform to FED-STD-751. When two or more seam or stitch types are given for the same part of an operation, any one of them may be used. Where stitch type 401 is used, the looper thread shall be on
34、 the the inside of the garment, Seam allowance shall be maintained with seams sewn so that no raw edges, run-Offs, twists, pleats, puckers or open seams will result, All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. 3.6.2 Stitch
35、ing per inch. The minimum and maximum number of stitches per inch shall be as specified in table II. 3a6.3 Thread breaks and ends of seams. Ends of all seams and stitching, when not caught in other seams and stitchings shall be backtacked not less than 1/4 inch, Thread breaks (all stitch types) shal
36、l be secured by stitching back of the break not less than 1/2 inch, on 401 stitch type may be repaired using 301 stitch type. continuous line of stitching (except labels) shall be overlapped not less than 1/2 inch. stitches , Skipped stitches or thread breaks Then ends of a The ends of label stitchi
37、ng shall be overlapped not less than 3 3,7 Manufacturing operations requirements. The coverall shall be manufactured in accordance with operation requirements specified in table II, The contractor is not required to follow the exact sequence of operations listed. manufacture is permissible, provided
38、 the thread does not show on the finished coverall , Any additional basting or holding stitching used to facilitate 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44002A( GL) 3.7.1 Marking, The cut parts shall be marked to insure a uniform s
39、hade and size throughout the garment, Any method of marking may be used except: a. Metal fastening devices, b. Sew-on type tickets c. Adhesive type tickets which leave traces of adhesive on the material after removal of the tickets, 7 Provided by IHSNot for ResaleNo reproduction or networking permit
40、ted without license from IHS-,-,-4 lili oc 2 U . w Fil wmw w w ww w w www w w ww - lo Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O 4 I co O0 O0 44 IlIl II II coco 00.m O00 o I n td U nn tdtd I I .1 LI vi .o0 Pua Lec *rl al o S4AU . m 11 - d a c
41、z 3 ! W m .J =! L l- u O IL O. o h c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4400ZA 42 = 9979906 023377b 3 2 MLL-C-44002A (GL) 14 w Fil w w c w w .w w w 2 I eo E: I 00 0, I ao eo E I O 4 I eo n P N 1 al VI VI v n P N I al VI VI v rl rl
42、ia4 I aci *- mod 5:“: in ri .o m 4 O m 4 O rn 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n a - e 8 o W . U U O P al al r-l rn a ti 2 8 % 3 $ M al d W “ U I IO .z : MIL-C-q4002A 42 W 9999906 0233777 5 W MIL-C-44002A (GL) K lu O u / i J c Lz c
43、EL u mo W Pa W W t -w -I W W z n Pa W W W grri uw“ O O O O LLLX rl 4 d rl k Co Co ao Co 2- 2“W W W 22c $5 I I I I n n n P hl hl N N I I I I al. al al o o o o CA w w w I4 I4 I4 I4 W P W no IQ 5: $ d 4 d d O O O O m m o m y I- Z W w b? -K U, 8,r E: vc: -2 O U al a p nal W ww w w wp9 c ta2 Ca w J mo mu
44、 dual =uf 9 u; $ *;1 3 wmr4mu w ww w W ww W x O I Co ao eo i-I 2 I 2 I 2 I eo O ri I ao I I 8 ri Ilri rl O O0 o m me cr) rl O m ct riri O0 me n a I 3 o W rn al al rl t! rn P e rl N rl d W f 4 W J I- z 3 K - w 3 H I- - fi m o OI Provided by IHSNot for ResaleNo reproduction or networking permitted wit
45、hout license from IHS-,-,-MIL-C-44002A 42 = 777770b 0233777 7 _ - - MIL-C-44002A (GL) O rl I ao O0 44 II aoao .o 4 I ao O 4 I ao 4 O m a .I $: I ao al k (d 3 a k cd a III al O rl rl rl (d E El 9 k a m a o al k 5 m E * 8 *rl al N *rl v) a E o h 2 *rl o U m n m U O 2 rl I4 o b! a d w c. x 3 J Y s d R
46、w m J F I- U O u. c O b b N 22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44002A( GL) 3.8 Finished measurements. The overgarment shall conform to finished measurements shown in table III when item is laid smooth and flat. TABLE III. Finish
47、ed measurements (in inches) Small Medium Large X-Large =-Large Tolerance Half Chest L/ 27-1/4 28-1/4 29-1/2 30-1/2 32-1/2 + 3/4 Sleeve length - 2/ 20-1/4 20-1/2 20-3/4 21 21-1/2 + 1/2 1/2 Waist 21-3/4 21-3/4 22-3/4 23-3/4 25 + 3/4 relaxed 3/ inseam i/ 30 30 30 30 31 + 3/4 - i/ - 21 Measure from fold
48、ed edge to folded edge at bottom of armhole. Measure from base of armhole to bottom edge of sleeve. vary in length by 1/2 inch or more on the same garment. Sleeves shall not 3/ Measure from side edge to side edge between rows of waist tunnel stitching. - 41 Measure along seam from crotch to bottom o
49、f leg. inlength by 1/2 inch or more on the same garment. Inseams shall not vary 3.9 Workmanship. The finished coveralls shall conform to the quality and grade of product established by this specification. shall not exceed the applicable quality level. The occurrence of defects 4, QUALITY ASSURANCE PROVISIONS 4.
