1、MIL-C-44111B 28 December 1990 SUPERSEDING MIL-C-4411 IA 31 July 1987 MILITARY SPECIFICATION COAT, MATERNITY, UTILITY WORK UNIFORM This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of maternity c
2、oat for the utility work uniform made of poplin cloth, woodland camouflage pattern. 1.2 Classification. The coat shall be of the sizes listed in table I as specified (see 6.2). TABLE I. Schedule of sizes Short Regular Long 6 8 10 12 14 6 8 10 12 14 6 8 ?O 12 14 Beneficial comments (recommendations,
3、additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of th
4、is document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44111B TABLE I. Schedule of sizes (contd) Short Regular Long 16 18 20
5、22 16 18 20 22 16 18 20 22 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents
6、 are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-50 198 A-A-50 I99 A-A-203 V-B-87 1 V-T-276 DDD-L -20 PPP-B-636 MILITARY MIL -L-35078 MIL-C-43468 - Thread
7、, Gimp, Cotton, Buttonhole - Thread, Polyester Core : - Paper, Kraft, Untreated - Button, Sewing Hole, and Button, Staple (Plastic) - Thread, Cotton - Label: For Clothing, Equipage and Tentage (General Use) - Boxes, Shipping, Fiberboard Cotton- or Polyester-Covered - Loads, Unit: Preparation of Semi
8、perishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For Cotton - Cloth y Camouflage Pattern, Wind Resistant Poplin , 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS FEDERAL FED-STD-595 - Colors U
9、sed in Government Procurements FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets by Att
10、ributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 1 1-5094. ) 2.2 Non-Government publications. The following documents form a
11、part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of th
12、e documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AWD MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) THE CO
13、LOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America Department of Defense Standard Shades for Buttons (Color cards may be available from the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color cards are not available from the Color Associat
14、ion, individual color samples may be obtained from the contracting activity or as directed by the contracting activity. 1 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44LELB 84 H 9999906 8467347 T I MIL-C-44111B AMERICAN ASSOCIATION OF TEX
15、TILE CHEMISTS AND COLORISTS (AATCC) Test Method 88B - Smoothness of Seams in Fabrics After Home Laundering (Application for copies should be addressed to the American Association of Textile Chemists and Colorists, Research Triangle Park, P.O. Box 12215, Durham, NC 27709. (Non-Government standards an
16、d other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services. 2.3 Order of precedence. In the event of a conflict between the text of this document and the re
17、ferences cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article in
18、spection (see 6.3) in accordance with 4.3. 3.2 Guide samples. Samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variation from this specification may appear in the sample, in which case this specification shall govern. 3.3 Material. It is encouraged that r
19、ecycled material be used when practical as long as it meets the requirements of this specification. 3.3.1 Basic material. The basic material shall be wind resistant cotton poplin cloth dyed in a woodland camouflage pattern conforming to type III of MIL-C-43468. 3.3.2 Thread and gimp. 9 3.3.2.1 Threa
20、d. The thread shall be polyester core, cotton-covered or polyester-covered conforming to A-A-50199, ticket Nos. 30, 2 or 3 ply; 50, 2 ply; and 70, 2 ply, except that cotton thread conforming to V-T- 276, ticket No. 70, 2 ply may be used to serge facings and fly. The threads shall be dyed Camouflage
21、Green 483 approximately color chip 34094 of FED-STD-595. 3.3.2.2 Gimp. The cotton gimp for reinforcing buttonholes shall be Camouflage Green 483 approximately color chip 34094 of FED-STD-595 and shall conform to type I or II, size No. 8 of A-A-50198. 4 Provided by IHSNot for ResaleNo reproduction or
22、 networking permitted without license from IHS-,-,-MIL-C-44111B 3.3.2.3 Colorfastness. The dyed thread and gimp shall show fastness to laundering equal to or better than the standard sample. sample is available, the dyed thread and gimp shall show I1good1 fastness to laundering. When no standard 3.3
23、.3 Labels. Each coat shall have a size label (class 2) and either a combination identification and instruction label (class 15) or separate identification (class 1) and instruction (class 3) labels conforming to type VI of DDD-L-20. of the finished labels shall be medium green and shall approximate
24、cable number 70034, 70130 or 70131 of the StandardColor Card of America. The following information shall be included in the printing required by DDD-L-20: The labels shall show fastness to laundering. The color Item description: COAT, MATERNITY, UTILITY WORK UNIFORM Body of instructions : 1. Wear ou
25、tside of slacks. 2. Adjust closures to ventilate; avoid overheating of body. 3. Machine washing. Use Permanent Press Cycle. IJash in warm water with mild detergent. 4. Hand washing. Wash in warm water using mild detergent. DO NOT WRING OR TWIST. Rinse in clean warm water. 5. DO NOT USE CHLORINE BLEA
26、CH OR STARCH. 6. Dry at low heat (do not exceed 130OF). room temperature for 10 minutes. Remove immediately from dryer. To drip dry, remove from water and place on rustproof hanger. After drying, tumble at 3.3.4 Buttons. 30-line of V-B-871. be shade Olive Green, BP Cable 62016 as specified in the Do
27、D Standard Shades for Buttons. The buttons shall conform to type II, class D, style 26, The buttons shall have a dull finish, and the color shall 3.4 Design. The design is a single-breasted coat style with collar, two patch pockets with flaps, a straight cut bottom, and side pleats with tabs. The co
28、at has a fly front and sleeves with tabs. 3.5 Figure. Figure 1 is furnished for information only. If there are inconsistencies between the written specification and the figure, the written specification shall control. 3.6 Patterns. Standard patterns, which provide an allowance of 3/8 inch for single
29、 needle and 1/2 inch for shoulder, backarm, sleeve setting, side and underarm seams, except as otherwise indicated, will be furnished by the Government to the contractor for cutting working patterns. Neither the Government patterns nor the working patterns shall be altered in any way. 5 Provided by
30、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44LLLB 84 I 9999906 0467349 3 I MIL-C-44111B 3.6.1 List of pattern parts. The components of the coat shall be cut from material in accordance with pattern parts as specified in table II. TABLE II. Pattern Dar
31、ts Mat er i al Pattern nomenclature Cut parts Basic material Front Back Collar I/ TOP sieve Und e r sleeve Sleeve tab Pocket patch Pocket flap Left front fly Side tab 2 1 2 2 2 4 2 2 1 4 - 1/ Collar may be cut in one piece with seam allowance along top edge deducted. 3.7 .Construction. 3.7.1 Stitche
32、s, seams, and stitching. Stitch, seam, and stitching types specified in table III are those covered by FED-STD-751. Whenever two or more methods, seams or stitching types are given for the same part of the operation, any one of them may be used. When stitch type 401 is used, the looper (under-thread
33、) shall be on the inside of the coat. Unless otherwise specified, double needle stitching shall be 3/16 to 1/4 inch gage with the outer row of stitching 1/16 inch from edge on outside of coat. The guides and knives on the overedge machines shall be set to trim only the ravelled ends of the fabric. S
34、eam allowances shall be maintained with seams sewn so that raw edges, run-Offs, twists, pleats, puckers, or open seams will not result. All seams shall start and finish evenly. Seams required to be worked out having a depth between the fold of 1/8 inch or more shall be considered a defect. 3.7.1.1 T
35、ype 301 stitching. Ends of all stitching shall be backstitched or overstitched not less than 1/11 inch, except where ends are turned under or caught in other seams or stitching. Ends of the continuous line of stitching shall be overlapped not less than 112 inch, except on labels where a minimum of t
36、hree stitch overlap is required. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. The lock shall be embedded in the materials sewn. 6 Provided by IHSNot fo
37、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44111B 84 U 99999Ob 04b7350 T = MIL-C-44111B 3.7.1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks or bobbin run-outs occur during stitching, the stitching s
38、hall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. 1/ - and 1/ - 3 b. Thread breaks or two or more consecutive skipped or run-off stitches The noted during inspection of the item shall be repaired by overstitching. stitching shall start a minimum of
39、1/2 inch in back of the defective area-and continue over the defective area a minimum of 1/2 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials restitching in the requir
40、ed manner. 1/ - When making the above repairs, the ends of the stitching are not required to be backstitched. 7.1.2 Types 101, 401, 503, and 504 stitching. Thread tension shall be maintained so that there will be no loose stitching. All repairs shall be in accordance with 3.7.1.1.la and 3.7.1.1.lb.
41、be accomplished by use of stitch type 301, except when used for eyelets. Repair; to stitch type 401 shall 3.7.2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in table III. 3.7.3 Buttonholes. 3.7.3.1 Eyelet-end tapered bar. The buttonholes in the pocket
42、flaps, sleeve tabs, cuffs, side tabs, left front, and left front fly shall be eyelet- end tapered bar type worked over gimp specified in 3.3.2.2 with not less than four tacking stitches at bar end catching gimp ends (not counting crossover stitch). between front facing and front plies. shall be on t
43、he outside of coat. The cut lengths shall be 3/4 to 7/8 inch, unless otherwise indicated in table III. The buttonholes shall be cleancut with the stitching securely caught in the fabric. The purling shall be on the outside of sleeve and panel tabs and Left front lapel buttonhole purling 3.7.4 Bartac
44、ks. Bartacks shall measure 1/4 inch to 1/2 inch long and shall be free from thread breaks and loose stitching. 3.8 Manufacturing operations requirements. The coat shall be manufactured in accordance with the operation requirements specified in table III. The contractor is not required to follow the
45、exact sequence of operations. Any basting or holding stitching required to facilitate manufacture is permissible provided the thread is removed or does not show on the finished coat, except on pockets which may be prehemmed. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted with
46、out license from IHS-,-,-MIL-C-44111B * 3.8.1 Use of automated apparel equipment. Automated apparel equipment may be used to perform any of the operations specified in table III, providing that the seam and stitch type are as specified and the finished component conforms to the required configuratio
47、n. pattern is forwarded, the component shall conform to that pattern. When a Government furnished shaper 3.9 Finished measurements. table IV. the collar shall be f. 1/4 inch. The finished measurements shall be as shown in All tolerances shall be f. 1/2 inch, except that the tolerance for 8 Provided
48、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44LLLB 4 I 9999906 04b7352 3 MIL-C-44111E ni 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44LLLB 84 = 9779906 0467353 5 = MIL-C-44111B O In fi o
49、s4 U u a a, o 8 a a, 3 a, P 4 fi ho c .ri s L (d E h O a O s .c, !4 2 4: P rl (d rld (d .cl .,-I hi sa, m u.0 a, o ma n-n -NM vvv a, L a, o bo c ,ri c o Q d Q Io rl a, e cd rl a, 30 5 c .Q * .A KI3 a c,c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a c, c O 0 - U H H H w i f3 6 2 MIL-C-44LLLB 84 m 999990b 04b735Y 7 W MIL-C-
