1、MIL-C-44124B 84 = 9999906 0493085 4 MI=-4 4 12 4B 30 Septanber 1991 SUPERSEDING MILrc-44124A 7 O distribution is unlimited. d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIM-44124B 2.1.1 swc ifications, standardc, and handbookc. ?he follming spec
2、ifi- cations, standaras, and handbookc form a part of this document to the extent specified herein. Unless othmice specified, the issues of these doc=umentS are those listed in the issue of the Departnient of Defense Index of Specifications and Skar Clothing, Fersonal Equipment and Equipage; General
3、 Specification For MIM-43668 - webbing, Textile, Bulked Nylon MIM-44034 - Cloth, mill, Cammflage Pattern, catton and Nylon for mert uniform EnmmRlx FEDERAL MIG105 - Sampling Pnx I O s$ rl rl e rl I O rl rl O CI rl O CI CI . e CI cv 21 Provided by IHSNot for ResaleNo reproduction or networking permit
4、ted without license from IHS-,-,-NIL-C-44324B 84 = 9799906 0493306 8 m , MIM-44124B 5i O 5i u) O u) O O O O v) u) u) v) 4; 3 I 4; I O rl 7 cr 3 3 rl O m Et m rl O m rl B ti6 3 .A 8-$ . c) (v 22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44
5、324B 84 = 7779906 0493307 T = I I O B I MIM-44124B O O O O In In In In O O O O In In In In 3 3 I 3 I O rl * rl I 3 o m rl O m o rl O m m 23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L! O In O in 24 P I 1 I 1 I I I I I l l I , I l l i I I I I l
6、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-443246 84 9999906 0493309 3 H a U ii B H H MIM-44124B O O O u) u) u) O O O u) v) u) 7 O rl f rl I rl O m Ei m 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
7、e from IHS-,-,-O v) O ln O u) O In e O m 0 (v I 26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a - li 8 H U H a NIL-C-44L24B 84 E 9999906 0493LLL L E MILrC-44124B O O O ul In In O O O In In In o m ai 27 Provided by IHSNot for ResaleNo reproductio
8、n or networking permitted without license from IHS-,-,-MIM-44124B b m 0 cv d m . 28 8. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44124B 84 9777906 0493113 5 = I I. 4 m 29 Provided by IHSNot for ResaleNo reproduction or networking permitte
9、d without license from IHS-,-,- MIL-C-44124B 4 9999906 0493114 7 - MIM-44124B 3.8 Finished rwzmmnmts. Finished measurements shall confonn to table III. TABU3 III. Table of meacurementS (inches) Size x-small small/raeaium Iarge/x-Iarge ToleranCe 1/2 ulest lJ 23 26-1/2 29-1/2 - +1 -2/ 24 26-3/4 27-1/2
10、 - +1 Attach cuver tapes by atta- back yoke hook fastener tape to amhole loop fastener tape, snap straps on the side W fmnt of mer to their finished position, close fmnt and lay flat on table. 1/ 1/2 chest - Measure froan the folded edge to folded ege of the cover in line with base of amhole. 2/ em-
11、th - Meacure on a straight line along center of back fm top edge of neck to bottom edge of cover. 3.9 WorlananshiD. ?lie finished mer &ail conform to the quality of product established by this specification and the cccurrence of defects shall not exceed the applicable acceptable quality levels. 4.1
12、Responsibilitv for inspect ion. riess otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection rquhxmmts (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may
13、 use his awn or any other facilities suitable for the perform- arce of the inspection rquhments specified herein, unless disappraved by the merment. incpeCtions set forth in this specification where su& inspections are deemed neoeccary to encure supplies and services conform to prescribed requirewnt
14、s. Ihe Government reserves the right to perfonn any of the 4.1.1 RemonsibilitV for ccm3 lianoe. All itens must meet al1 requirements of sections 3 and 5. beccene a part of the contractorls averall inspection system or quality program. shall not relieve the contractor of the respnsibility of ensurhq
15、that ali proituctrs or supplies submitted to the Gavermient for acceptance campiy with ali requirements of the contract. facturing operations, is an acceptable practice to ascertain conformance to -ts, however, this does not authorize submission of knwn defective material, either indicated or adual,
16、 nor does it chnit the Governme.nt to accept defective material. The inspection set forth in this specification shall The abcence of any inspection requirements in the specification sampling inspection, as part of mu- 30 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
