1、MIL-C-Qq3QOA 999970b II970507 19 H MI M-4 4 3 4 OA 30 SePtanber 1993 SLTPERSEDING MIM-44340 (GL) 29 June 1988 MILITARY SPECIFICATION CAN, TRAY PACK This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE AND CLASSIFICATION 1.1 saw. This specifica
2、tion covers the requirements for a ribbed bdy and ribbed lid tinplated steel tray pack can. 2.1 Government doc=umentc. 2.1.1 spec ifications, standards, and handbooks. The following specifica- Unless otherwise specified, the issues of these documents tions, standards, and handbooks fonn a part of th
3、is document to the extent specified herein. are those listed in the issue of the Departnent of Defense index of Specifications and standards (DoDiss) anc supplement thereto, cited in the solicitation (see 6. i) . 0 Beneficial cammentc (recommendations, additions, deletions) and any pertinent data wh
4、ich may be used in impr0Vh-q this document should be addressed to: U.S. Anny Natick Fksearch, Development, and Wineering Center, Natick, MA 01760-5018 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this dcament or by letter. AFUISC N/A FSC 8110 DIST
5、RiEWTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44340A 9 9999906 1970508 750 MIM-4 4 34 OA 3, SPECIFICATIONS Tr-c-495 - Coatings, Exterior, for Tinned Food Cans PPP-B
6、-636 - Boxes, Shipping, Fiberboad MIUTARY MIG105 - Sarrp?ling Procedures and Tables for Inspection by Attributes (Unless otherwise indicated, copies of federal and military specifications, standardc, and handbookc are available fm the Standaxdization Documents Oder Desk, milding 4D, 700 Robbins Aven
7、ue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawinqs, and publications. ?he follahg other Goveniment documente, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified,
8、U.S. DEPART“? OF HEALTH AND HUMAN SERVICFS (HI-E), U.S. FD AND DI7uG ACMINISTRATION (rn) Federal Food, Drug, and Cosmetic Act and Regulations PrCJrmrlgate Thereunder (21 CFR Parts 1-199) (copies are available fm the Superintdent of Documents, U.S. Governt Printing Office, Washington, Dc 20402-0001.)
9、 (Non-Govemmnt standardc and other publications are normally available fram the organizations that prepare or distribute the documente. dcaawnts also may be available in or through libraries or other informational services. ) These 2.3 Mer of precedence. in the event of a conflict between the text o
10、f this document and the references cited herein, the text of this document takes precedence. Nothhg in this doc=ument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3.1 Can materials. All materials shall conform with 21 Code of Federal Regulations
11、 (CFR), Federal Food, Drug, and Cosmetic Act, as amended, and regulations pdgated thereunder. be used when practical as long as it meets the requirements of this specification. it is encourageci that recycled material 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
12、ense from IHS-,-,-MIL-C-44340A m 999990b 1970509 697 = MIM-4434OA 3.1.1 Tin plate steel. The can body shall be constructed fram sheets and the lid from coils of matte finish of 25/75 (0.125/0.375 poundc per 3mse box) differentially coated electrolytic tin plate. sufficient temper and haranecs to pro
13、tect food produ& during shipment and storage. pounds per base box. 0 The steel shall be of The base plate weight of the can body an can lids shall be 90 3.1.2 Interior can coatinq. The entire inside area of the can body shall be coated with a base coat of epoxy phenolic and a top layer of aluminum v
14、inyl, and the inside area of the lid shall be coated with a base coat of clear vinyl and a top layer of aluminum vinyl. with the provisions of the CFR, Food and Drugs, Title 21, chapter 1, Subpart C - Food Additives, Section 175.300, Recinous and polymeric Coatings. scratches or fractures shall not
15、penetrate through the interior can coating. The interior can coat- shall not peel or blister when in contact with the prduct. packagd product. The enamel usecl shall confonn Ihe interior can coating shall neither affect or be affected by the 3.1.3 Exterior can coatinq. The can shall be coated on the
16、 outside with a coating conforming to Typ I or spe III of TT-C-495 (see 6.1). 3.2 Can desiqn and fabrication. size can in accordance with figures 1 and 2. of approximately 105 fluid ounces. ribbed style. for the double seaming operation. cammercial standars. and placed properly so that it forms a ti
17、ght seal but will not be squeezed internally into the food. The lid and bcdy shall be capable of achieving a double seam thereby creating a hermetic seal. The can shall be fabricated ushg methods that reflect good standards of worlananchip and quality in the finished product. The can shall be a 1001
18、 by 1206 by 200 The can shall have a capacity The design of the bcdy and lid shall be The curl of the lids shall be compound-lined in preparation The Seaming campound shall camply with The campound shall be of adequate munt and adherence 3.2.1 Ribbed stvle. 3.2.1.1 m. The body design shall be reinfo
19、rced on the bottan with six longitudinal beads or ribs 0.050 f 0.010 inches deep (see figure 1). beads shall be 9 inches by 3/4 inch in length and width and shall be equidistant in the center panel of the bottom. be outward. apex of these beads shall be inward. The The apex of the beads shall The si
20、des shall be reinforced with beads and corner flutes. “he 3.2.1.2 &d. The lid design shall be reinforced with eight longitudinal beads 0.018 f 0.004 inches deep (see figure 1). by 3/4 inch in length and width and shall be equidistant in the Center panel of the lid. The center four kads on the lid de
21、sign shall be interrupted to provide a 5 inch by 5 inch flat center panel for labeling. beads shall be outward. The beads shall be 11 inches The apex of these 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44340A 77777Ob 1770510 309 = MIM-44
22、34OA 3.3 Can condition. The can bodies and lids shall be clean. mere shall be no dirt or stab on the cans. shall be no excessive oil present. If the cans are coated with oil, then 4. QALXiY ASCURANCE PROVISIONS 4.1 Resmnsibilitv for inspect ion. Unless otherwise specified in the contract or purchase
23、 order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use their own or any other facilities suitable for the performance of the inspect
24、ion requirementc specified herein, unless disapproved by the Government. any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. The Government resemes the right to perform 4.1.1 Certificat
25、es of cana3 liance. The contractor shall furnish certificates of conpliance for the requirements in 3.1.1, 3.1.2, and 3.1.3. 4.2 lity conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIGSTD-105. 4.2.1 Campo nent and material inspection
26、. In accordance with 4.1, componente and materials shall be inspected in accordance with all the requirementc of referend doc=uments unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.2.2 End item visual examination. The end items shal
27、l be examined for the defects listed in table I. can bodies or can lids, and the sample unit shall be one can body or one can lid. (AQL) , expressed in terms of defects per hundred units, shall be 1.0. The lot size shall be expressed in units of nie inspection level shall be S-4 and the acceptable q
28、uality level TABLE I. End item defects category Defect Mai or 101 102 103 104 105 Not style specified Scratch or fracture in interior coating Feel or blister of interior coating mtire inner surface not coated Reinforcing beads not as specified 4 Provided by IHSNot for ResaleNo reproduction or networ
29、king permitted without license from IHS-,-,-MIL-C-4434OA 799990b 1770511 245 MIM-4434 OA TABLF: I. End item defects (contad) Qtegory Defect Maior 106 iabel panel not as specified (lid only) 107 pretence of dents or scratches 108 Dirty or stained 109 110 Inadequate or excessive anwunt of seaming camp
30、ound (lid only) Seaming catpound not of adequate adherence (lid only) 111 Seaming campound not properly placed (lid only) 4.2.3 Extemal can coatins examination. Examina * tion of the external can coating shall be in accordance with “T-C-495. examined for the defectc specified in table II. expresse i
31、n shipping containers, and the sample unit shall be one filled in temiC of defects per hundred units, shall be 2.5 for major defects and 4.0 for minor defects. 4.2.4 packasins examination. The cans and shipping containers shall be The lot size shall be TAEU3 II. PackaqinS defects category Defect Mai
32、or Minor 101 interior packing with kraft paper not as specified 102 Number of cans or lids not as specified 201 2 02 mcessive oil on cans cans are dirty or stained 203 Box not snug-fitting 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIM-4434OA
33、5. PACKAGING 5.1 packing. Can bodies and lids shall be packed separately. Bodies shall be nested 35 per shipping container with a sheet of dry wax coated kraft paper placed between each body. The stack of bodies shall be packed in a snug-fitting fhxbcard box, constructe an cloced in accordance with
34、style RSC, class damestic, grade 275 of PPP-El-636. nie dimensions of the box shall be 12-3/4 inches in length 10-5/8 inches in width, and 15-3/8 inches in depth. The stack of lids accorLlam=e with Style RSC, class damestic, grade 275 of PPPCB-636. di.me.nsions of the box shall be 13 inches in lengt
35、h, 10-5/8 inches in width, arid 6-1/2 inches in depth. Lids shall be nested 90 per shipping Container. shall be packed in a snug-fitting f&erhard box, constructed and closed in The 6. “ES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.
36、) 6.1 Acquisition requ irementS. Acquisition documente must specify the following: a. b. c. Title, number, and date of this specification. Issue of DODISS to be cited in the solicitation, and if required, the Type of exterior can coating required (see 3.1.3). specific issue of individual documente r
37、eferenced (see 2.1.1). 6.2 subie& term (key word) listing. ccanbat field feeding Metal food container operational ration 6.3 Chara es fram previ- issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extmsiveness of the changes. cus
38、todians: Preparing activity: Army - GL Navy - SA Air Force - 50 Amiy - GL (Project 8110-0303) Review activities: Amry-MD,czM Navy - MC DIA -SS 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t c NIL-C-44340A W 9999906 L9705L3 018 m MIM-44 340A io i
39、 SIDE GOTTOM END Figure 1. Tray Pack Food Container. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-C-44340A H 9999906 1970514 T54 MIM-4434OA INSIDE EDGE OF DOUBLE SEAM J 4 FLUTED CORNER Figure 2. Tray Pack Can Nanienclature. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
