1、MIL-C-44417 84 9999906 0472355 1 W 21 February 1991 MILITARY SPECIFICATION CARRIER, BODY ARMIR, SMALL ARMS PRCQFCCIVE, AIR(=REw, SURVIVAL This specification is approved for use by the Natick Research, Developnt, and Engineering Center, Department of the Army, and is available for use by all Departme
2、nts and Agencies of the Departmnt of Defense. 1. SCOPE 1.1 Scope. insert to be worn by aircrew personnel. survival system. Equipnt (= distribution is unlimited. Licensed by Information Handling ServicesMIL-C-44417 84 9977906 0472356 3 m 2.1.1 Specifications, standads, and handbooks. The following sp
3、ecifications, standads, and handbooks form a part of this doc=ument to the extent specified herein. documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DDISS) and supplement thereto, cited in the solicitation (see 6.2). Unless otherwise specifi
4、ed, the issues of these SPECIFICATIONS FEDERAT, A-A-50083 V-T-295 DDD-L-20 PPP-B-6 36 MILITARY MIL-W-4088 MIL-T-50 38 MIL-W-5664 MIL-F-21840 MIL-L-35078 MIL-C-43128 MIL-W-43668 MIL-C-43842 MIL-C-44050 MIL-B-44421 STANDARDS FEDERAT, FED-STD-595 FED-STD-751 MILITARY MIL-STD- 105 MIL-STD-129 MIL-STD-14
5、 7 MIL-STD-970 Bag, Plastic, Folded Garnient Thread, Nylon Label, For Clothing, Equipage, and Tentage (General Use) Boxes, Skipping, Fiberboard Webbing, Textile, Woven Nylon Tape, Textile and Webbing, Textile, Reinforcing, Webbing, Textile, Elastic Fastener Tapes, Hook and imp, Synthetic mds, Unit:
6、Preparation of Semiperishable Nylon Subsistence Items; Clothing, Personal Equipent and Equipage; General Specification For Cloth, Plain Weave, Nylon: Webbing, Textile, Textured or Multifilament Cloth, Oxford, Aramid Cloth, Ballistic, Aramid Body Armor, Small ument, hawever, supersedes applicable law
7、s and regulations unless a specific exemption has been obtained. 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide samples. Samples, when furnished, are solely for guidance and information to the contracto
8、r (see 6.4). Variation from this specification may appear in the sample, in which case this specification shall govern. 3 Licensed by Information Handling ServicesMIL-C-44417 84 999790b 0472358 7 H MIL-C-44417 (a) 3.3 Materials and components. The materials and components shall be as Materials and c
9、omponents specified herein and on the applicable drawings. not specified shall be selected by the contractor in accordance with MIL-STD-970. Materials and components specified in accordance with MIL-STD-970 shall not degrade the operational suitability or effectiveness of the carrier. as long as it
10、meets the requiremnts of this specification. It is encouraged that recycled material be used when practical 3.3.1 Cloth, oxford, aramid. The oxford aramid cloth used for the body of the carrier shall conform to MIL-C-43842. The color shall be Olive Green 106. 3.3.2 Cloth, ballistic, aramid. The ball
11、istic aramid cloth used for the insert shall conform to type II, class 2 of MIL-C-44050. 3.3.3 Thread, nylon. The thread used throughout the carrier shall be types I, II or III, class A, letter size E or FF conforming to VJT-295. color shall be Camouflage Green 483 approximating color chip 34094 of
12、FED-m-595. The 3.3.4 Fastener taw, hook and loop, synthetic. The fastener tape shall be type I, class 1 conforming to MIL-F-21840. in table I. The color shall be Olive Green 106. The widths shall be as specified 3.3.5 Webbinq, textile, woven nylon. The nylon webbing usei for the harness and pull str
13、ap shall be type VIII, class 1 conforming to MIL-W-4088. The color shall be Olive Drab 7. 3.3.6 Webbinq, textile, elastic. The elastic webbing used for the side waist adjustment straps shall be type II, class 1, 1-1/2 inches wide conformning to MIL-W-5664. The color shall be Olive Green 106. 3.3.7 W
14、ebbinq, textile, textured or multifilament nylon. The webbing used The on the harness support loop shall be type III confonning to MIL-W-43668. color shall be Olive Drab 7. 3.3.8 Buckle, side release, 2 inch. The buckle used for securing the harness shall conform to Drawing 2-6-100. 3.3.9 Tape and w
15、ebbinq, nylon. The tape used for the harness support loop and binding the ballistic cloth insert shall be type IV, class 2, 1 inch wide conforming to MIL-T-5038. The color shall be Olive Drab 7. 3.3.10 Labels. Each carrier shall have a combination size, identification and instruction label positione
16、d on the inside of the back. conform to type VI, class 14 of DDD-L-20 with the following exceptions and detailed requirements. The label shall 4 Licensed by Information Handling ServicesMIL-C-4i.14l17 8i.1 m 9997906 Oi.172359 7 MIL-C-44417 (CL) a. The size characters for the instruction label, excep
17、t capital letters, shall be 1/16 inch minimum. minimum. Ail capital letters shall be 3/32 inch b. The label material shall be nylon conforming to MIL-C-43128, except it shall not be water-repellent treated. Medium Green 614 matching the standami sample (see 6.4). The label material shall be dyed c.
18、The required permanent coating shall not apply. d. The label shall Shaw fastness to laundering in accordance with class 14 of DDD-L-20. e. The instruction label shall contain the follawing information: READ THESE INSXKTIONS (XWVLJLY WASHING INS-IONS FOR CARRIER, BODY ARMOR, SIGCL ARMS PFUlECCIVE, AI
19、RCREM, SURVIVAL Hand wash in wann water ( 1200F) and mild 1. Hand/Machine Washing. laundry detergent or machine wash at permanent press cycle. 2. Rinsinq. Rinse thoroughly in clear wann water after laundering. Ail detergents must be rmved. tumble dry with the temperature dial set at permanent press
20、cycle. After rinsing, hang the carrier to drip dry or 3. Fixed launderinq procedure. Wash the carrier according to laundry wash fomla “K“ of FM-10-17. Lightly extract, then tumble dry at 180% (82OC) maximum. 4. Field laun rocedure. Wash the carrier according to laundry wash formula “1“ of TM %2:0. L
21、ightly extract, then tumble dry at 180% (82OC) maximum. 5. Do NcTr STARCH OR USE CHLORINE BLEACH UNDER ANY CONDITIONS. 6. Do Ncrp DRY CLEAN. D Ncrr RENIVE THIS LABEL. 7. WARNING: Launder with the hook and loop fastener tapes engaged. Do not press hook and loop fasteners. 3.3.11 Identification markin
22、q. The words “Do N(Tr DROP“ and “WARNING: EN- HOOK AND LXXIP ARE PMPEF corroded areas; Size or type not as specified Not assembled as specified, improperly burrs or sharp edges 116 117 set or reversed, failing to serve intended purpose 118 Finish Omitted or not as specified 2 18 unitted, illegible,
23、misplaced Not type and class specified Not positioned as specified Not stitched on all four sides Label stitching through the printing HemS Less than specified width on hems Adjustment strap Improperly threaded, i.e., causing buckle to finish on reverse side or to function improperly strap not as sp
24、ecified function and buckle Turned under edge of adjustment Buckle defective, affecting 2 19 119 323 324 220 22 1 222 325 223 4.4.4 defects listed in table III. carriers. be S-3 and the AQL, expressed in tem of defects per hundred units, shall 4.0. End item examination for fit. The end items shall b
25、e tested for the The lot size shall be expressed in units of The sample unit shall be one carrier. The inspection level shall 21 Licensed by Information Handling ServicesMIL-C-44417 84 9999906 0472376 9 MIL-C-44417 (CL) TABLE III. Fit defects Classification Examine Defect Maior Minor “E: Fit examina
26、tion shall be acomplished with the ceramic body armor insert for which the carrier is designed. inspector shall ease the ceramic armor insert into the carrier without effort and close the opening securely with the touch and hold fastener tape. The Fit of ceramic Carrier too small, i.e., ceramic body
27、 armor insert in carrier into carrier 101 (see 6.4) bocty mr insert fails to fit Fastener tape fails to effect a Carrier too large, showing excessive smth and secure closure 201 fullness or wrinkles 202 4.4.5 Packaqinq examination. The fully packaged end items shall be examined for the defects liste
28、d below. units of shipping containers. container fully packaged. expressed in tem of defects per hundred units, shall be 2.5. The lot size shall be expressed in The sample unit shall be one shipping The inspection level shall be S-2 and the AQL, Examine Defect Marking (exterior Qnitted; incorrect; i
29、llegible; of improper size, and interior) location, sequence, or method of application Materials Any component missing, damaged, or not as specified Workmanship Inadequate application of components, such as Bulged or distorted container incomplete sealing or closure of flap, improper taping, loose s
30、trapping, or inadequate stapling Contents Number per container is more or less than specified 4.4.6 Palletization examination. The fully packaged and palletized end The sample unit shall be one items shall be examined for defects listed belaw. The lot size shall be expressed in units of palletized u
31、nit loads. palletized unit load, fully packaged. the AQL, expressed in terms of defects per hundred units, shall be 6.5. The inspection level shall be S-1 and 22 Licensed by Information Handling ServicesMIL-C-44417 84 m 9999906 0472377 O m Examine MILS-44417 (CL) Defect Finished Length, width, or he
32、ight exceeds specified maximum dimensions requirements Palletization Pallet pattern not as specified Load not bonded as specified Weight Exceeds maximum lcad limits Marking unitted; incorrect; illegible; of improper size, location, sequence, or methcd of application 5. PACKAGING 5.1 Preservation. Pr
33、eservation shall be level A or Comnercial, as speci- fied (see 6.2). 5.1.1 Level A presenration. 5.1.1.1 Carrier, when procured separately (type I). folded to measure approximately 17 inches by 14 inches. be unit packed in a plastic bag conforming to A-A-50083. The ceramic bocty armor insert conform
34、lng to MIL-B-44421 shall be placed in a carrier of the correct size and the flap secured. Each carrier shall be Each carrier shall 5.1.1.2 Carrier, when p- with ceramic bodv armor insert (tvpe 111. 5.1.2 Comnercial presenration. Each carrier or carrier and body armor assembly shall be preserved in a
35、ccordance with ASIM D 3951. 5.2 Packinq. Packing shall be level A, B or Comerical, as specified (see 6.2). 5.2.1 Level A mckinq. 5.2.1.1 Carrier, when procured separately (type I). Wnty carriers of one size only, preserved as specified in 5.1, shall be packed in a shipping container conforming to st
36、yle Rsc-L, grade V2s of PPP-B-636. dimensions of each shipping container shall approximate 17-1/4 inches in length, 14 inches in width and 12 inches in depth. shall be closed, waterproofed and reinforced in accordance with the appendix of PPP-B-636. accordance with MIL-L-35078 for the tupe and class
37、 of load specified (see 6.2). F loads. Inside Each shipping container Shipping containers shall be arranged in unit loads in Strapping shall be limited to nonmetallic strapping for type II, class 23 Licensed by Information Handling ServicesMIL-C-44417 84 = 9799906 0472378 2 MIL-C-44417 (CL) 5.2.1.2
38、Carrier, when procured with ceramic body mr insert (tm 11). Each carrier with ceramic hdy armor insert of one size only, preserved as specified in 5.1, shall be packed in a shipping container conforming to style Rsc-I;, grade V2s of PPP-B-636. Inside dimensions of each shipping container for sizes s
39、mall and medium shall approximate 14-1/2 inches in length, 12-1/2 inches in width and 8 inches in depth. container for sizes long and X-long shall approximate 15-1/4 inches in length, 14-1/2 inches width and 8-1/2 inches in depth. container shall be closed, waterproofed and reinforced in accordance
40、with the appndix of PPP-B-636. in accordance with MIL-L-35078 for the type and class of load specified (see 6.2). F loas. Inside dimensions of the shipping Each shipping Shipping containers shall be axranged in unit loads Strapping shall be limited to nonmetallic strapping for type II, class 5.2.2 L
41、evel B packinq. 5.2.2.1 Carrier, when procured separately (type I). Wnty carriers of one size only, preserved as specified in 5.1, shall be packed in a shipping container conforming to style Rsc-L, tp CF (variety SW) or SF, class domestic, grade 275 of PPP-B-636. container shall approximate 17-1/4 i
42、nches in length, 14 inches in width and 12 inches in depth. with method II as specified in the appendix of PPP-B-636. Inside dimensions of each shipping Each shipping container shall be closed in accordance 5.2.2.2 Carrier, when procured with ceramic bdy armor insert (type 11). Each carrier with cer
43、amic hdy annor insert of one size only, preserved as specified in 5.1, shall be packed in a shipping container confonning to style Rsc-L, tp CF (variety SW) or SF, class domestic, grade 275 of PPP-B-636. Inside dimensions of each shipping container for sizes short and medium shall approximate 14-1/2
44、 inches in length, 12-1/2 inches in width and 8 inches in depth. X-long shall approximate 15-1/4 inches in length, 14-1/2 inches in width and 8-1/2 inches in depth. with method II as specified in the appendix of PPP-B-636. Inside dimensions of each shipping container for sizes long and Each shipping
45、 container shall be closed in accordance 5.2.2.3 Weather-resistant shippinq container. When specified (see 6.2), shipping containers shall be a grade VC, VS, or V4s fiberboard box fabricated in accordance with PPP-B-636 and closed in accordance with the appndix of PPP-B-636. 5.2.3 Comercial packinq.
46、 Carriers (type I) or carriers with ceramic body armor insert (typ II), preserved as specified in 5.1, shall be packed in accordance with ASIM D 3951. 5.3 Palletization. When specified (see 6.2), carriers (type I) or carriers with ceramic bocty mr insert (type II), packed as specified in 5.2.2 or 5.
47、2.3 shall be palletized on a 4-way entry pallet in accordance with 24 Licensed by Information Handling ServicesMIL-C-44417 4 W 999990b 0472379 4 W MIL-C-44417(&) load type Ia of MIL-STD-147. type IV or type V in accordance with MIL-SITI-147. be bonded with primary and secondary straps in accordance
48、with bonding means C and D or film bonding mans F or G. accordance with the appendix of MIL-SID-147. or purchase order, shipping containers and palletized unit loads shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. Pallet types shall be type I (4-way entry), Each prepare
49、d load shall Pallet pattern shall be number 95 in 5.4 Markinq. In addition to any special marking required by the contract 6. N0IF.S (This section contains information of a general or explanatory nature that 6.1 Intended use. my be helpful, but is not mdatory.) The carrier with a ceramic bocty annor insert is intended to be worn over the chest area to provide protection from small arms fire for aircrw members exposed to survival and recovery procedures. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. b. C. d. e. f. 9. h. i. Title, nm-ber and date of
