1、PA_- MIL-C-63113 13 - 7779706 03g3870 - MIL-C-63113 (AR) 28 JULY 1977 MILITARY SPECIFICATION CARTRIDGE, 40MM, YELLOW SMOKE, CANOPY, M676 METAL PARTS FOR AND LOADING, ASSEMBLING AND PACKING This specification is approved for use by the UDS, Army Armament Research and Development Command and is availa
2、ble for use by all Departments and Agencies of the Department of Defense . 1. SCOPE 1.1 This specification contains requirements not normally covered by the drawings and provides quality assurance provisions for the fabrication of parts and load- ing, assembling and packing for Cartridge, 40MM, Yell
3、ow Smoke, Canopy, M676. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. - The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-P-223 - Black Powder MIL-C-5
4、541 - Chemical Films and Chemical Film Materials for Aluminum and Aluminum Alloys Assurance Provisions, General Specification For MIL-A-48078 - Ammunition, Standard Quality FSC: 1310 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving t
5、his document should be addressed to: Commander, US Army Armament Research and Development Command, Attn. DRDAR- Cluster or Smoke Canopy or Parachute for Cartridge, 40MM, White Star, Cluster or Smoke Canopy or Parachute INSPECTION EQUIPMENT DRAWINGS 9202770 - Chamber Gage 9202783 - Alignment Check 88
6、27895 - Limit Check 2.2 Other Publications. - The followdg documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply. CODE OF FEDERAL REGULATIONS TITLE 49 - Transp
7、ortation, Parts 100-199 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b3LL3 13 U 7777706 0343872 L _ MIL-C-63113 (AR) (The Code of Federal Regulations is available from the Super- intendent of Documents, U.S. Government Printing Office, Was
8、hington, D.C. 20402. Orders should specify “49 CFR 100- 199 (latest revision) I) . AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM B 117-73 - Standard Method of Salt Spray (Fog) Testing (Application for copies should be addressed to: American Society for Testing and Materials, 1916 Race Street, Phil
9、a- delphia, Pa. 19103) 3. REQUIREMBNTS 3.1 Material. - Materials shall be in accordance with the applicable drawings and specifications. 3.2 Cartridge. - The cartridge shall comply with all requirements specified on Drawing (Dwg.) 9255142 all asso- ciated drawings, and with all requirements specifie
10、d in applicable specificaitons. 3.3 Transportation vibration. - The cartridge shall comply with the following requirements: 3.3.1 The cartridge shall be safe to transport following this test (See 6.5) . 3.3.2 There shall be no evidence of external damage to the cartridge that will affect the intende
11、d function (See 6.6) . 3.4 Functioning. - The cartridge shall comply withthe 3.4.1 Altitude. - The projectile shall function at an following requirements; average altitude of 300 feet plus (i.) 50 feet or minus (-) 25 feetwith no item below 200 feet. 3.4.2 Burning- of smoke ssernbly. - The smoke ass
12、embly shall imite and emit smoke for 100 3. 20 seconds whibe sus- pended $romthe parachute at ambient temperature. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63LL3 13 M 7977706 O343873 3 Ei I MIL-C-63113 (AR) 3.4.3 Parachute. - The parac
13、hute shall not separate from the smoke assembly at ejection or delay opening from time of ejection for more than 5 seconds. 3.4.4 Firing. - No projectile shall stick in the gun bore and the projectile shall not burst or eject the smoke assembly 50 feet from the launcher. 3 . 4 . 5 . Hiit TenpeYa.t;L
14、ir (160 decEres F. pls or mins 5 degres F) - The -cartridge shall comply with the require- ments of 3.4.1, 3.4.2, 3.4.3 and 3.4.4. 3 . 4 o 6 . ambient temperatiire (70 degres I?. pls r. minus 5 degres F). - The cartridge shall comply with the require- ments of 3.4.1, 3.4.2, 3.*4.3 and 3.4,4. . .co.l
15、,d .t . . . . . . 0. emperatre- (-65 degrees F. pls. or Minus 5 degree-s. F). - The cartridge shall comply withthe re- quirements of 3.4.1, 3.4.2, 3.4.3 and 3.4.4. 3, . Fi,r, . . . . . st article InspecYion. - This specification contains technical provisions for first article inspec- tion. samples b
16、y the contractor shall be as specified in the contract . Requirements- for the submission of first article 3.6 Workhianship. - All parts and assemblies shall be fabricated, loaded and assembled in a thorough, workmanlike manner. They shall be free of burrs, sharp edges, cracks, dirt, grease, rust an
17、d other foreign matter. The cleaning method used shall not be injurious to any parts, nor shall the parts be contaminated by the cleaning agents. surface coatings shall be continuous; however, a few light scratches not exposing base material may be permitted. Ail required marking and stampling shall
18、 be neat and sharply defined. Exterior 4. QUALITY ASSURANCE PROVISIONS 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63LL3 13 H 7999706 03q387Lt 5 R MIL-(2-63113 (AR) 4,2 Class5if5caeln Bf Inspeetions . - The following types of inspec-tion
19、shall be .conducted on this item: a. First Article Inspection b. Quality Conformance Inspection 4 . 3 First article .inspection . - 4.3-1 . Submission. - The contractor shall submit a first article as designated by the Contracting Officer for evaluation in accordance with the provisions of 4.3.2. sa
20、mple shall consist of the following items in sample quantities as indicated. The first article Description Body Disc anchor Ogive Smoke canisters Disc, ejection Case, Smoke Housing delay Parachute assembly Smoke canister loading assembly Smoke assembly Delay loading assembly Cartridges Drawing 92439
21、00 9252374 9233964 9252377 9252397 9255798 9252378 9252371 9252368 9274459 9 25 236 9 9255142 Quantity 25 (5 painted) 25 25 25 25 25 25 (5 for salt spray) 25 25 25 25 465(4440 to a Government Proving Ground for function- ing tests) 4.3.2 Inspections to be performed, - See MIL-A-48078 and Table 1: he
22、rein. 4.3.3 Rejection. - See MIL-A-48078 and the following; 4 . 3 . 3 . 1 Proving Ground Tests a. Any critical-defect occurs in any phase (Table III) . b. Average altitude of the total sample fails the applicable requirement (Table III and 3.4.1). 5 Provided by IHSNot for ResaleNo reproduction or ne
23、tworking permitted without license from IHS-,-,-1 - MIL-C-63LL3 13 m 7779706 0343875 7 m MIL-C-63113 (AR) C. A total of eight (8) or more in the hot phase I fail any of the following: I (3) Altitude less than 200 ft (Table III). Bi d. A total of twenty-two (22) or more in the ambient phase fail any
24、of the following; (i) Parachute failure (3.4.3) . (2) Item fails to function (Table (III). (3) Altitude less than 200 ft (Table III). (4) Burning time incorrect (average) (3.4.2) . e. A total of eight (8) or more in the cold phase fail any of the following: (i) Parachute failure (3.4.3) . I (2) Item
25、 fails to function (Table III). (3) Altitude less than 200 ft (Table III). I 6 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. . . . I . . .- . r P ci r P U C I- I- a - . I* . . . -_- MIL-C-b3113 13 797970b 0343876 7 rn -I-, 5 s 5 a o a c (d a, M
26、 a .rl k c, k Cd u d Cu m v m o s Ad Cu Cu CUP Cu Cu. N . drn t d PLD P- d -v . . . dd d d PP P P P Cucu Cu Cu cucu Cu Cu N mm m .o mo o o O OLD m m Om m m LrJ Cu Cu Cu Cu Y Cu n Col b cil : v mo 7 -.I- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
27、-MIL-C-63113 13 m 9999906 0343877 O m I (u .8 t Y) n; w o L, c al c O a E O o a s (d % a 4 il I) u I ,. . . . OSTmm In *n m PT t P T PPPV VPP .P In Q Pm (uCu Cu (u (u (ucu(u(u n!(u(u om m C) m mmmm omm o. . in Lo Lo L! L-) Ulm00 O00 h (u Cu (u (u nJ(uuvv a)#co fP (u o o E 5 o U o o, k al a C O o al
28、-Pl 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63LL3 I3 777770b 0343878 2 MIL-C-63113 (AR) 4.4 Quality conformance inspecticm. - 4 . 4 . 1 Inspectin: lt formtion . - inspection lots shall comply with the lot formation provisions of MIL-A
29、-48078. addition, each inspection lot shall contain: In a. Projectile metal parts from one interfix lot number from one manufacturer. b. Delay composition from not more than one lot number. C. . Smoke composition produced by one manufacturer under one continuous set of operating conditions and which
30、 consist of one or more batches that have beensubjected to the same unit chemical or physical mixing process intended to make the final product homogeneous. lot number from one manufacturer. from one manufacturer. number, from one manufacturer. one lot number d. Cartridge case loaded assemblies from
31、 one interfix e. Smoke assemblies from one interfix lot number f. Ignition composition from not more than one lot g. Delay Assemblies from one interfix lot number . g. Disc ejection composition from not more than 4.4.2 Examination. - See MIL-A-48078. a. . Sampllng Plans. - Unless otherwise specified
32、 in the Classification of Defects and Test Tables, sampling plans for major and minor defects shall be in accordance with MIL- STD-105, nspection Levei II. 9 rr -. . . . i, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rl LL O rl I- W W I Lo 1 m om
33、 m mmmm mmw mmmv?mmm * I I 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i-l 8 ri t; m w MIL-C-63113 13 W 7779706 0343880 O W sr 5 8 ti c 2 m 2 m rl 8 3 8B 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
34、om IHS-,-,-CI E 4 v m rl rl m iD Y d E cn cn Y c c - . MIL-C-63113 13 7779706 03q3881 2 rl ul .rl b- 8 ? m a z 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9 rl a, I2 MIL-C-63113 13 7977906 0343882 4 9 E- .kJ E 33 Provided by IHSNot for ResaleN
35、o reproduction or networking permitted without license from IHS-,-,-3 v m rl rl m u) rn Y k c Fi L O d I 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I- Y I u) =e O0 00000000 15 Provided by IHSNot for ResaleNo reproduction or networking permitt
36、ed without license from IHS-,-,-rl b rl. c W W i!i k 16 ! Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rl m u) Y MIL-C-631L3 13 m 7977906 0,3Lt3b L m d m 2 d: o i 3 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without li
37、cense from IHS-,-,-MIL-C-b3LL3 13 W 777770b 0393887 3 rl c, rl 2 I v) $i 1 aJ .$ a u) u) id m O rl ai tl 2 id V ! E .n a* orl O cI m u P 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Fi B rl MIL-C-63113 13 7779906 03LI38 5% ?Y? mmmm O000 3 2 Pro
38、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-C-b3113 13 W 7797906 0343889 7 W 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63113 13 7977906 0343870 3 W I rl ci rl c! m # Y rl Cu m -$
39、 . . Id z B v: 21 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-d W m Y d r. *. K O s s U - O ci a, v) ai % 22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63L13 13 W 7797706 0343872 7 88 w
40、w * O0 23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I ri k ri * d MIL-C-b3LL3 13 W 7977706 0343873 7 m 4 NCJ *# mm m. O 2 ri al a 24 L Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63113
41、 13 W 777770b 0343874 O W I m a, P cI O Cu cn 5 m ? m g ,gg 88 o O0 d:? FI drl om O rn a, tn a tn 25 m d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O00 O0 a al z! al m m (d Provided by IHSNot for ResaleNo reproduction or networking permitted wit
42、hout license from IHS-,-,-h v % Y m FI W R d x T MIL-C-63113 13 W 9999906 O343896 4 M si% 22 O0 * a .rl w al a al 2 E c, Y u) u) al !i LI .rl 4 al 27 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rn rn Y I- I= Y d: ! d aJ 28 Provided by IHSNot for
43、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b3L13 13 9999906 03q39 - M ML-C-6 3 11 3 (AR) MaeeYia 1 Drawing . Delay Composition Ignition Composition Composition Ejection Disc Smoke Composition 9252369 9255797 9252399 9255797 The contractor shall provide adequate
44、controls to insure com- pliance with the requirements and shall test for verification at least one (1) sample of each material from each eight hours production of cartridges. Composite samples shall not be used, If the moisture content of a sample exceeds the requirement and loading has not begun, t
45、hat quantity of material repre- sented by the sample shall be rejected. If assemblies have been loaded with material containing excessive moisture, the remaining material that is represented by the sample together with all ccartridges loaded with the non-forming material shall be rejected. 4.4.3.2 K
46、ir pres.sre - This test shall be conducted 100 percent. Any cartridge which fails to comply with the requirement specified on the applicable drawing shall be classified defective.and removed from the lot. 4.4.3.3 Transportation-Vibration. - After completion of the 100 percent air pressure test and b
47、eginning with the first lot produced and continuing until three (3) -acceptable lots (lots not accepted by disposition) have complied with the acceptance criteria specified in Table II, two-hundred and sixty-four (264) cartridges shall be selected from each lot, packed in their regular shipping containers and sub- jected to this test. The cartridges shall be observed and examined visually without disassembly for any evidence of failure to comply with the requirements of Tab
