1、MIL-C-63128 (PA) 15 February 1977 MILITARY SPECIFICATION CARTRIDGES: 40MM, GROUND SMOKE MARKERS, M713, M715 AND M716; BODY PART FOR This specification is approved for use by Picatinny Arsenal, Department of the Army and is available for use by all Depart- ments and Agencies of the Department of Defe
2、nse. 1.1 This specificatdon contains requirements not normally covered by the drawings and provides quality assurance provisions for the fabrication of one type of Body for Cartridges: 40MM, Ground Smoke Markers, M713, M715 and M716. 2.1 Issues of documents.-The following documents of the issue in e
3、ffect on date of invitation for bids or reauest for proposal, form a part of f ied herein. z .- SPECIFICATIONS MILITARY MIL-C-5541 MIL-A-4 8 O 78 STANDARDS MILITARY MIL-STD-105 MIL-STD-1169- DRAWINGS this specification to the e#tent speci- Chemical Films and Chemical Film Materials for Aluminum and
4、Aluminum Alloys Ammunition, Standard QualityAssurance Provisions, General Specification For Sampling Procedures and Tables for Inspection by Attributes Packaging, Packing and Marking for Shipment of Inert Anununition Components Beneficial comments (recommendations, additions, deletions) and any pert
5、inent data which may be of use in improving this document should be addressed to: Commander, Picatinny Arsenal, Dover, New Jersey 07801 by using the self-addressed Standard- ization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC: 1310 , THIS DOCU
6、MENT CONTAINS JQ. PAGES. B _ . _.- .I -“p- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-63L28 13 9999906 03Y4272 T MIL-(2-63128 (PA) PICATINNY ARSENAL 9258731 - Body 2.2 Other publications.-The following documents form a part of this specifi
7、cation to the extent specified herein. otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply. Unless AEIERICAN SOCIETY FOR TESTING AND MATERIALS ASTM B 117-73 - Standard Kethod of Salt Spray (Foy; Testing (Application for copies should be add
8、ressed to: American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pa. 19103) rn 3. REQUIREMENTS . 3.1 Material.-Materials shall be in accordance with the applicable drawings and specifications. 3.2 Part.-The part shall comply with all requireinents speci- fied on Drawing (Dwg.)
9、9258731, all associated drawings, and with all requirements specified in applicable specifications. technical provisions for first article inspection. for the submission of first article samples by the contractor shall be as specified in the contract. 3.3 First Article Inspection.-This specification
10、 contains Requirements 3.4 Workmanship.-Al1 parts shall be fabricated and finished in a thorough, workmanlike manner. chips, sharp edges, cracks, unblended radii, surface defects, dirt, grease, rust, corrosion products, and other foreign matter. The cleaning method used shall not be injurious to any
11、 parts, nor shall the parts be contaminated by the cleaning agents. marking and stamping shall be neat and sharply defined. They shall be free of burrs, All 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection and Standard Quality . Assurance Frovisions .-Unless otherwise specified here
12、in or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. z 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63128 (PA) 4.2 Classification of Inspections.-The following types of i
13、nspectfs item: a. First Article Inspection b. Quality Conformance Inspection 4.3 First Article Inspection 4.3.1 Submissibn.-The contractor shall submit a first article as designated by the Contracting Officer for evaluation in accordance with the provisions of 4.3.2. sample shall consist of the- fol
14、lowing items in sample quantities as indicated. The first article Part Description Body Drawings 9258731 Quantity 25 (5 painted) 4.3.2 Table 1 herein. Inspections to be Performed.-See MIL-A-48078 and . 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
15、,-. i ! NN I om on N 4 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-b3L28 13 9999906 0344275 5 MIL-C-63128 (PA) 4.3.3 Re? ectlon . -See MIL-A-4 8 O 7 8. 4.4 Quality Conformance Inspection 4.4.1 Inspection Lot Formation.-Inspection lots sh
16、all comply with the lot formation provisions of MIL-A-48078. 4,4.2 Examination.-See MIL-A-48078. a. Sampling p1ahs.-Unless otherwise specified in the Classification of Defects and Test Tables, sampling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. 5
17、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-13 9999906 03qLi29b i I hc C *., v C .ri al P O ci k O .rl k P a al C r( b al a al C Ls di I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b312
18、13 7779706 034Li277 9 W c Zl wo. Cu b is gP (u- * E v, $8 r mmm . OdCu GGi4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. i b a: a) pr: 8 * 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C
19、-63128 13 W 777770b 0344277 2 MIL-C-63128 (PA) 4.4.3 Testing.-Testing is described in the First Article and Quality Conformance Inspection Tables. 4.4.4 Inspection Equipment,-The inspection equipment required to perform the examinations and tests prescribed herein is described in the Paragraph Refer
20、ence/Inspection Method column in the tables starting with Paragraph 4.4.2.1. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 6 o% MIL-A-48078 and 6.3 herein. 4.5 Test methods a-4 procedures 4.5.1 Salt spray.-This test sh
21、all be conducted in accord- ance with ASTM-B 117-73. Salt solution shall be 5 percent. Parts so tested shall not be returned to the lot. 5. PACKAGING 5.1 Preservation and packaging 5,l.l Level C.-The body shall be preserved and packaged in accordance with MIL-STD-1169. 5.2 Packinq in 5.1.1, 1169 . 5
22、.3 STD-1169 . 5.4 5.2.1 Level C.-The body preserved and packaged as specified shall be packed for shipment in accordance with MIL-STD- Marking.-Marking of the carton shall comply with MLL- Shipping.-When components from more than one lot are shipped as a carload, each lot shall be kept separate, and
23、 the division between lots clearly indicated to prevent mixing of the lots in transit. 6. . NOTES 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-6312 13 E 7779906 034Li300 5 E MIL-C-63128 (PA) cation is intended for use on Cartridges: 40MM,
24、Ground Smoke Markers, M713, M715 and M716. 6.1 Intended Use.-The component covered by this specifi- 6.2 .Drderiig Data.-See MIL-A-48078. 6.3 Submission of Inspection Equipment Desiqns for Approva1.- See MIL-A-48078. ATTN: DRDAR-QAA-I, ARRADCOM, Dover, New Jersey 07801. Submit equipment designs as required to Commander, Custodian: Project Number: 1310-A-O99 Amy-PA Preparing Activity: Army-PA U. & GOVERNMENT PRINTINQ OFFICD 77.705020/2411 10 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
