1、MIL-C-63 267 (AR) 13 July 1984 SUPERSEDING FA-PD-MI-2673 Rev O 30 June 1965 MILITARY SPEC IF1 CAT I ON CASE, CARTRIDGE, BLANK 105MM, M15B2 This spcification is approved for use by the US Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the De
2、partment of Defense. 1. SCOPE 1.1 Scope. This specification contains requirements not covered by the drawings and provides quality assurance provisions for the fabrication of parts for Case, Cartridge, Blank, 105MM, M15B2. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on
3、 date of invitation for bids, or request for proposals, form a part of this specification to the extent specified herein. SPEC IF1 CATIONS , MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions I General Specifications for STANDARDS MIL ITARY . MIL-STD- 105 - Sampling Procedures
4、and Tables for I nspec ti on by Attribut es FEDERAL FED-STD-151 - Metals; Test Methods FSC: 1315 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, US Arm Armament Research and Developme
5、nt Center, Attn. DRSMC-QA, Dover, New Arsey 07801 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I I THIS DOCUMENT CONTAINS 9 PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted witho
6、ut license from IHS-,-,-MIL-C-63267 13 W 9999906 0346843 9 = MIL-C-6 3 2 6 7 (AR) 2.1.1 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publica- tions form a part of this specification to the extent specified herein. DRAWINGS (See 6.6)
7、U.S. ARMY ARMAMENT .RESEARCH AND DEVELOPMENT CENTER (ARDC) 7548320 - Ammunition for Interplant Shipment of Brass, Aluminum and Spirally Wrapped Steel Cartridge Cases, Empty, 75MM to 120MM Inclusive 10534917 - Case, Cartridge, Blank, 105MM, M15B2 (Copies of specifications, standards, handbooks, drawi
8、ngs, and publications required by manufacturers in connectionwith specific acquisition functions should be obtained from the contracting activity or as directed by the contracting. officer. 1 2.1.2 Order of precedence. In the event of a conflict between the text of this specification and the referen
9、ces cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Material. Materials shall be in accordance with the applicable drawings and specifications. 3.2 Parts. The parts shall comply with all requirements specified on drawing (dwg.) 10534917, associated drawings an
10、d with all requirements specified in applicable specifications, and standards. dance with the applicable drawing and the specification listed. salt spray for 168 hours. Test pieces shall comply with the requirements of the applicable drawing and the specification listed. ! 3.3 Protective finish. Pro
11、tective finish shall be in accor- 3.4 Corrosion resistance. Following exposure to five percent 3.5 Maximum profile. The maximum profile of the cartridge case shall comply with the requirementstof the applicable drawing. 3.6 Workmanship. Each cartridge case shall be free from cracks, splits, seams, d
12、eep scratches, burrs (those which may interfere with assembly or prove injurious to personnel handling the item) or foreign matter which may impair proper functioning. 2 . . _I . .:. . ? . ? , , .- . . . . i.: _ *,-. r .-. . I . Provided by IHSNot for ResaleNo reproduction or networking permitted wi
13、thout license from IHS-,-,-MIL-C-63267 (AR) 4 . QUALITY ASSURANCE PROVISIONS 4.1. Responsibility for inspection and standard quality assur- ance provisions. Unless otherwise specified herein or in the contract, the provisions sf MIL-A-48078 shall apply and are hereby made a part of this detail speci
14、fication. 4.2 Classification of inspections. The following types of inspection shall be conducted on this item: a. First article inspection. b. Quality conformance inspection. 4.3 First article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Cont
15、racting Officer for evaluation in accordance with provisions of 4.3.2. The first article sample shall consist of 30 Cases, Cartridge, Blank, 105MM, M15B2. Four cases of the 30 shall be used for protective finish tests after completion of Mechanical/Visual inspections. 4.3.2 Inspections to be perform
16、ed. See MIL-A-48078 and Table I 4.3.3 Rejection. See MIL-A-48078. specified herein . 4.4 Quality conformance inspection. 4.4.1 Inspection lot formation. Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination. See MIL-A-48078. a. Samplinq plans. Unless otherw
17、ise specified in the Classification of Defects and Test Tables, sampling plans for Major and Minor defects shall be in accordance with MIL-STD-105, Inspec- tion Level II. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63267 13 m 7779706 039b
18、95 2 m el in d a c in ii O d Y c lu rl aJ tn u .I4 Li ci u lu u a, I) lu u b a b O* M 4 M I -I e O E O c, #- #- 8 v) a, o lu n ai L r- M Co 07 I =c rl O W 4 n E O IL I i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 z I. . h U 2 l- W N M w I u I
19、z c r VI J r fi n 8 Y Y Z O F E a 3 u (v F9 In rl In i O rl Y rl cp a, oi rn -4 Li u & m u Q, rll m u 2 4 4 a. a. b . . b 00000 o O0 O0 00000 O0 a, Li 3uO 5Q ou 4 acv al - 8 u cc us Q -4 o a, riri EE O0 4J u a, Li E E c E -4 -4 Li a, u a, 5 -4 u a, u III u I O 3u u O Q -4 c .4 E . 44 4 h E Provided
20、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b32b7 13 W 777970b 03L1b47 b W nl In rl a E In i, O l-i A! c Id rl a i a, P 5 .rl & c, & m u ai u) m u h li CJ * Tjc e e - dPdP dPdP InIn Inm WW UW . O0 O0 .e o. e 5 al E: .rl aJ 5 2 O Z -I c O E O I4 CY a
21、 v1 a u la P a L r) n P, z1 -I I- l- I n 3 9 I E O LL o 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b32b7 13 W 7777706 03L(681(8 8 M rl drl rl m ma m fl flap fl In mm In D ww w O O0 o o . a 5 a, c -4 u-l a, 5 a, c O z c oi 3 O & Y W 8 a,
22、m .u - I a, LI 8 oi Li u c 8 U 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b32b7 13 777990b 03Llb8119 T MIL-(2-63267 (AR) 4.4.3 Testing. Testing is described in the First Article and Quality Conformance Inspection table. 4.4.3.1 Maximum p
23、rofile. Each cartridge case shall be gaged in a contractor certified maximum profile gage. Failure of any cartridge case to freely enter the-gage in such manner as to permit the slide to close without interference shall be cause for rejec- tion of the cartridge case. 4.4.3.2 Protective finish. 4.4.3
24、.2.1 Salt spray. Four cartridge cases from the initial production sample and four cartridge cases from each production lot shall be subjected to this test to determine compliance with 3.4. Failure of one or more cartridge cases to comply shall be cause for rejection of the initial production sample
25、or production lot . . 4.4.4 Inspection equipment. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48078 and Paragraph 6.3 herein. 4.5 Test methods and procedures. 4.5.1 Salt spray. Procedures and equipment use
26、d in performing this test shall be as prescribed in Federal Test Method Standard No. 151. 5. PACKAGING 5.1 Packaging requirements Packaging shall be as specified on dwg. 7548320. 6. NOTES 6.1 Intended use. The components covered by this specification are intended for use on 75MM Howitzers. 6.2 Order
27、ing data. See MIL-A-48078, 6.3 Submission of inspection procedures and equipment designs for approval. See MIL-A-48078. Submit equipment designs, as required to Commander, US Army Armament Research and Development Center, ATTN: DRSMC-QAR-I (D) , Dover, NJ 07801. 8 Provided by IHSNot for ResaleNo rep
28、roduction or networking permitted without license from IHS-,-,-NIL-C-63267 13 7779706 0346850 b .- MIL-C- 6 3 26 7 (AR) 6.4 Drawings. Drawings listed in Section 2 of this specifica- tion under the heading US Army Armament Research and Development Center may also include drawings prepared by, and ide
29、ntified as Edgewood Arsenal, Frankford Arsenal, Rock Island Arsenal, Picatinny Arsenal or ARRADCOM drawings. by these activities is now urider the cognizance of ARDC. Technical data originally prepared 6.5 Changes from previous issue. Asterisks are not used in this revision to identify changes with
30、respect to the previous issue, due to the extensiveness of the changes. t Custodian: Army-AR Preparing activity: Army-AR (Project 1315-A171) *U.S. BbVERNMENT PRINTING OFFICE 1984 - 606-038/A4641 9 / -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
