1、Y INCH-POUND MIL-(2-63405 (AR) AMENDMENT 4 1 September 1992 SUPERSEDING AMENDMENT 3 31 May 1991 MILITARY SPECIFICATION CHARGE, PROPELLING, 155MM, -M119A2 LOADING, ASSEMBLING AND PACKING This Amendment forms a part of Military Specification MIL-C-63405 (AR) dated 11 September 1980 and is approved for
2、 use by the US Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1 DRAWINGS: Delete “9333957“ and substitute “9331261“. Delete “PA37A1“ and substitute “PA99“. Container, Ammo, Metal PA99 for Charge, Propellin
3、g, 155MM, M119A2“ and substitute “9333957 - Packing and Marking for Container, Ammo, Metal: PA37A1 for Charge, Propelling, 155MM, M119A2“ (This reinstates the use of the round end container, dwg 9333957, which was replaced by the square end container, dwg 9331261, by Amendment 1, dated 20 Jul 81). 2
4、.1 DRAWINGS: Delete “9331261 - Packing and Marking for 2.1 DRAWINGS: Add the following new drawings: “ 12 9 13 7 5 3 19-48-4231/53A AMSC N/A DISTRIBUTION STATEMENT A. - Packing and Marking for Container, Ammo, Metal: PA131 for Charge, Propelling, 155MM, M119A2 (alternate) - Unitization Procedure for
5、 Ammunition and Components Packed in Cylindrical Metal or Plastic Containers on 4-Way Entry Metal Pallets 1 of 5 FSC I3*O Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-C-63405 (4) 13 = 99999Ob 11b4827 883 MIL-(2-63405 (AR) AMENDMENT 4 PAGE 3 * A
6、dd the following paragraph: “3.9.1 First article test. Test samples shall be withdrawn from the first lot produced by the contractor and tested in ac- cordance with all the requirements of this specification and Table III. Until the first article test has been performed and found to be acceptable, t
7、he contractor is in no way authorized by the Government to initiate the second lot production unless otherwise directed by the contracting officer.“ PAGE 7 TABLE II: Delete “Dwg 9333954 and 9333957“ and substitute “Dwg 9333954 and 9331261“. TABLE II: Delete “Dwg 9333954 and 93331261“ and substitute
8、“Dwg 9333954 and 9333957“ (This reinstates the use of the round end container, dwg 9333957, which was replaced by the square end container, dwg 9331261, by Amendment 1, dated 20 Jul 81). TABLE II: Delete “Dwg 9333954 and 9333957“ and substitute “Dwg 9333954 and 9333957/12913753“. PAGE 8 * 4.4.la: Ad
9、d the following at the end of paragraph: “Entire lot of propellant shall be utilized in the formation of one lot of propelling charge unless otherwise approved by the contracting officer.“ PAGE 19 4.4.2.11, Major Defect 104: Delete “reducer pockets“ and substitute “reducer pockets (see note) “. NOTE
10、S: Add the following: “If a fixed spacing double-needle sewing machine is utilized to control flash reducer pocket width, in lieu of gaging the pocket width, the needle width setting shall be gaged at the beginning of each shift.“ 2 Licensed by Information Handling ServicesMIL-C-63405 (4) 13 m 99999
11、0b LLb4828 71T m MIL-(2-63405 (AR) AMENDMENT 4 PAGE 26 4.4.2.17, Drawing Number: Delete “9333957“ and substitute “9331261“. 4.4.2.17, Drawing Number: Delete “9331261“ and substitute “9333957“ (This reinstates the use of the round end container, dwg 9333957, which was replaced by the square end conta
12、iner, dwg 9331261, by Amendment 1, dated 20 Jul 81). 4.4.2.17, Drawing Number: Delete “9333957“ and substitute “9 3 3 3 9 5 7 / 12 9 13 7 5 3 I . PAGE 27 4.4.2.18, Drawing Number: Delete “9333957“ and substitute It 9 3 3 12 6 1“ . 4.4.2.18, Drawing Number: Delete “9331261“ and substitute “9333957“ (
13、This reinstates the use of the round end container, dwg 9333957, which was replaced by the square end container, dwg 9331261, by Amendment 1, dated 20 Jul 81). 4.4.2.18, Drawing Number: Delete “9333957“ and substitute 9 3 3 3 9 57 / 12 9 137 5 3 I . PAGE 28 4.4.2.19, Drawing Number: Delete “9333957“
14、 and substitute I 9 3 3 12 6 1 I . 4.4.2.19, Drawing Number: Delete “9331261“ and substitute “9333957“ (This reinstates the use of the round end container, dwg 9333957, which was replaced by the square end container, dwg 9331261, by Amendment 1, dated 20 Jul 81). 4.4.2.19, Drawing Number: Delete “93
15、33957“ and substitute I 9 3 3 3 9 5 7 / 12 9 13 7 5 3“ . PAGE 31 5., Delete “PREPARATION FOR DELIVERY“ and substitute “Packaging“. 5.1: Delete “drawing 9333957“ and substitute “drawing 9331261“. 3 Licensed by Information Handling ServicesMIL-C-63405 (AR) AMENDMENT 4 5.1, Delete paragraph 5.1 in its
16、entirety and substitute the following: “5.1 Preservation and packaqinq. N/A 5.2 Packing. 5.2.1 Level A. The propelling charges shall be packed, sealed and tested in accordance with the specified requirements of drawing 9333957/12913753. 5.2.2 Level B. Pack the same as Level A. 5.2.3. Level C. Pack t
17、he same as Level A. 5.3 Marking. Markings shall be in accordance with the specified requirements of drawing 9333957/12913753.“ Add new paragraph 5.4: “5.4 Unitization. The propelling charges from paragraph 5.1 shall be unitized in accordance with drawing 19-48-4231/53A.“ PAGE 32 * Add the following
18、paragraph: “6.12 First article test. The first article test is a one time qualification test for a new contractor to load, assemble and pack acceptable M119A2 propelling charges. Once a contrac- tor has demonstrated the ability to load, assemble and pack the M119A2 propelling charge, the first artic
19、le test may be waived by the contracting officer. The following test program shall be used for the first article test: Table III First article test Test Phase Temp No. Control No. Test TECOM (deg F) Rounds Rounds TOP - Propellant 70 Checkout 145 -60 Sequential 145 Environmental -60 15 15 4 60 TOP-4-
20、2-504 60 TOP-4 - 2 - 5 04 “ 10 TOP-4-2-504 10 TOP-4-2-504 10 TOP-4-2-504 Licensed by Information Handling ServicesMIL-C-b3405 (4) 13 999990b llb11830 378 MIL-C-63405 (AR) AMENDMENT 4 0 NOTE: or vertical lines to indicate where changes (additions, modifica- tions, corrections, deletions) from the pre
21、vious amendment were made. This was done as a convenience only and the Government as- sumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content ir- respective of the marginal notations and relationship to the last previous amendment. The margins of this amendment are marked with an asterisk Custodian: Army-AR Preparing activity: Army - AR (Project 1320-AC88) 5 Licensed by Information Handling Services
