1、I- MIL-D-2088B (AR) AMENDMENT 2 14 August 1981 SUPERSEDING AMENDMENT 1 19 March 1971 MILITARY SPECIFICATION DEMOLITION KIT, BANGALORE TORPEW, M1A2 AND TORPEDO, BANGALORE, MlAl, INERT, PARTS FOR This amendment forms a part of Military Specificatin MIL-D-2088B (MU), dated 27 August 1968. Page 1 *Add t
2、he following Preamble underneath the title: “This specification is approved by the US Army Armament Research and Development Command, and is available for use by all Departments and Agencies of the Department of Defense.“ 2.1 Specifications, Military: Delete “MIL-1-45607 - Inspection Equipment, Supp
3、ly and Maintenance of.“ *3.4: Delete in its entirety and substitute the following: “3.4 Dents. - The tube shall be classed defective if there is evidence of any dent within four (4) inches of a flange, or if there is evidence of more than four (4) dents or any dent deeper than 1/8 inch beyond four (
4、4) inches from a flange.“ 4.1.1: following: “b. Drawing and specification number and date, together with identification and date of changes thereto. c. A statement that all material purchased by the contractor meets requirements, when such material is controlled by Government or commercial specifica
5、tions referenced in any of the contractual documents, and the certificates of conformance are on file and available for review. Delete statements b“ .through “g“ and substitute the d. Number of items in the lot. e. Date submitted. FSC 1375 THIS DOCUMENT CONTAINS -3 PAGES Provided by IHSNot for Resal
6、eNo reproduction or networking permitted without license from IHS-,-,-MIL-D-20B (2) 33 W 7799906 0293733 7 m ;83 MIL-D-2088B (AR) AMENDMENT 2 Page 4 4.2.1, Fifth sentence: Delete n(see -4.l.le),” .Page 5 $ 4.2.3, Third and fourth sentences: Delete in their entirety. 4.3.1: Delets in its entirety and
7、 substitute the following: “4.3.1 Lot formation. - The term “inspection lot” as used in this specification is defined as an essentially homogeneous collection of units of product from which a .representative sample in drawn and inspected to determine conformance with applicable require- ments. The s
8、ample selected shall represent only,that quantity of units from which he sample was drawn and shall not be construed to represent any prior or subsequentquantities presented for inspecton. Homogeneity shall be considered to exist provided the inspection lot has been produced by one manfacturer, in o
9、ne unchanged process, using the same materials and methods, in accordance with the same drawings, same drawing revisions, .same specifications and same specification revisions and complies with the grovisionsfor submission of product as specified in MIL-STD-105. Changes to the process, specification
10、s, or drawings not affecting safety, performance, interchangeability, or storage, as determined by the Government, shall not be deemed to alter the homogeneity of an inspection lot. inspection in accordance with this specification shall comply with the homogeneity criteria specifed herein regardless
11、 of the type of sampling procedure which is being applied to determine conformance with requirements. Lot numbering, as .required, shall be in accordance with MIL-STD-1168.” All material submitted for Pige 6 4.3.2: Delete in its entirety and substitute the following: “4.3,2 Examination. - The examin
12、ations listed in the following subparagraphs shall be performed on inspection lots (see 4.3.1) cf the components or assemblies designated in the applicable paragraph headings. Inspection for-critical defects (and major defects, when so specified) shall be 100 percent. Sampling plans for major and mi
13、nor defects shall be in accordance with MIL-STD-105 except that continuous Sampling plans in accordance with MIL-STD-1235 may be used if approved by the Government. . Instead of applying the AQLs designated herein to the groups of major and minor defects listed, the contractor may elect to apply AQL
14、S to individual defects using an AQL of 0.40 percent for each major defect and an AQL of 0.65 percent for each minor defect. . Page 2 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-D-20888 (2) 13 9797706 0271732 9 - 1 MIL-D-2088B (AR) AMF
15、NDMENT 2 When this method is elected, it shall be applied to all of the major and minor defects listed in the applicable subparagraph of this sectioni exept where 100 percent inspection is specified, and be documented as part of the contractors inspections system. Equipment necessary for the perform
16、ance of the inspections listed 1 shall be-in accordance wlth 4.3;4.“ Page 7 4.3.2.2, Major Category: Delete Major.Defect 101 j,n its er;tirety and substitute the following: “101. Concentricity of hole with tube mating shoulder . Gage 02001.“ Page 9 4.3.2.6, Major Category: Delete Major-Defect 101 in
17、 its entirety and substitute the following: “101. Concentricity of inside diameter of detonator well with tube mating shoulder o end cap.Gage 06001.“ Page 11 “4.3.2.9, Major Category: - “112. Dent deeper than“ 1/8 inchb.Gage 10014.“ Delete Major Defect 109 in its entirety. Add new Major Defect 8112
18、follows: Page. 13 4.3.4.2: Delete in its.ekitirety. 4.3.4.3: Delete in its entirety. “The margins of this amendment are marked with an asterisk to indicate where changes (additions, modifications, corrections, de1e:;ions) from the previous amendment were made. This was done as a convenience only and
19、 the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of .this document based on the entire content irrespective of the marginal notations and relstionship to thelast previous amendment. Custodian: Army - AR I Preparing Activity: Army - AR Project No: 1375-A205 ._ - Page 3 of 3 Q U.& GOVERNMENT PRINTINO OWlCt: lW1 O - 7QJ-OtJW -1 -1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
