ARMY MIL-DTL-11132 29 H-2013 INSIGNIA GRADE CADET AIRMAN JROTC U S AIR FORCE.pdf

上传人:ownview251 文档编号:442628 上传时间:2018-11-15 格式:PDF 页数:3 大小:141.41KB
下载 相关 举报
ARMY MIL-DTL-11132 29 H-2013 INSIGNIA GRADE CADET AIRMAN JROTC U S AIR FORCE.pdf_第1页
第1页 / 共3页
ARMY MIL-DTL-11132 29 H-2013 INSIGNIA GRADE CADET AIRMAN JROTC U S AIR FORCE.pdf_第2页
第2页 / 共3页
ARMY MIL-DTL-11132 29 H-2013 INSIGNIA GRADE CADET AIRMAN JROTC U S AIR FORCE.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 AMSC N/A Page 1 of 3 FSC 8455 INCH - POUND MIL-DTL-11132/29H 4 March 2013 SUPERSEDING MIL-DTL-11132/29G 20 November 1998 DETAIL SPECIFICATION SHEET INSIGNIA, GRADE, CADET, AIRMAN, JROTC, U.S. AIR FORCE This specification is approved for use by all Departments and Agencies of the Department of Defen

2、se The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-11132. MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230) FINISH: BASE: Epoxy resin (Stoning epoxy), Nickel Plated, Mirror-like Polished and shall match The Institute

3、 of Heraldry (TIOH) Metal Finish Chip Number 16. DEVICE: Epoxy resin, 24K Gold Plated, Mirror-like Polished and shall match TIOH Metal Chip Number 6. DIMENSIONS: BASE: HEIGHT (Overall): 11/16 inch (REF) WIDTH (Overall): 1-1/16 inches (REF) THICKNESS (Edge): 0.065 inch + 0.005 inch Provided by IHSNot

4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/29H Page 2 of 3 DEVICE: HEIGHT (Overall): 1/2 inch (REF) WIDTH (Overall): 1/8 inch (REF) THICKNESS (Edge): 0.085 inch + 0.005 inch ASSEMBLED (Thickest Point): 0.150 inch + 0.010 inch EPOXY: Epoxy resin shal

5、l be applied to the insignia grade as indicated above, and shall match TIOH Hard Enamel Color Chip Numbers listed below. Hard cloisonn enamel may be used in lieu of epoxy. If hard cloisonn enamel is used, the required base material shall be Gilding Metal 95/5 (UNS Alloy C-210). TIOH HARD ENAMEL COLO

6、R CHIPS COLOR CHIP NUMBER Blue #18 Red #1 Light Blue #30 ATTACHING DEVICE: 1. The device shall be secured to the base by two solid brass rivets 0.035 inch minimum in diameter located on the vertical center line of the device. 2. Attaching device shall be prong and clutch type. 3. Prongs shall be att

7、ached on the horizontal center line, equidistant from each side and 7/8 inch + 1/32 inch apart. NOTES: 1. The term (REF) refers to the measurements taken from the obverse Government furnished hub or die. 2. The base may be rhodium plated with mirror-like polished finish at the option of the manufact

8、urer. 3. Acid test for the gold plated device shall not apply. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted w

9、ithout license from IHS-,-,-MIL-DTL-11132/29H Page 3 of 3 Custodians: Preparing activity: Army - IH Army - IH Air Force - 11 Review activity: (Project No. 8455-2013-131) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ARMY

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1