ARMY MIL-DTL-11132 8 F-2013 INSIGNIA RANK CADET COLONEL ROTC AND JROTC U S AIR FORCE.pdf

上传人:lawfemale396 文档编号:442630 上传时间:2018-11-15 格式:PDF 页数:3 大小:143.67KB
下载 相关 举报
ARMY MIL-DTL-11132 8 F-2013 INSIGNIA RANK CADET COLONEL ROTC AND JROTC U S AIR FORCE.pdf_第1页
第1页 / 共3页
ARMY MIL-DTL-11132 8 F-2013 INSIGNIA RANK CADET COLONEL ROTC AND JROTC U S AIR FORCE.pdf_第2页
第2页 / 共3页
ARMY MIL-DTL-11132 8 F-2013 INSIGNIA RANK CADET COLONEL ROTC AND JROTC U S AIR FORCE.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 AMSC N/A Page 1 of 3 FSC 8455 INCH - POUND MIL-DTL-11132/8F 4 March 2013 SUPERSEDING MIL-DTL-11132/8E 6 June 1997 DETAIL SPECIFICATION SHEET INSIGNIA, RANK, CADET, COLONEL, ROTC AND JROTC, U.S. AIR FORCE This specification is approved for use by all Departments and Agencies of the Department of Def

2、ense The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-11132. DASH NO. -1: ROTC Regular Size -2: ROTC Miniature Size -3: JRTOC (see Note 2) MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230) FINISH: Epoxy resin (Stoning

3、 epoxy), Nickel Plated, Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/8F Page 2 of 3 DIMENSIONS: HEIGHT (Overall): -1: 2-1/4 inches (REF

4、) -2, -3: 1-3/16 inches (REF) WIDTH (Overall) -1: 1-5/16 inches (REF) -2, -3: 11/16 inch (REF) THICKNESS (Overall): 0.065 inch + 0.010 inch -1, -2: 0.070 inch + 0.010 inch -3: 0.100 inch + 0.010 inch (Including Plastic Back Plate) EPOXY: Epoxy resin shall be applied to the insignia rank as indicated

5、 above, and shall match TIOH Hard Enamel Color Chip Numbers listed below. Hard cloisonn enamel may be used in lieu of epoxy. If hard cloisonn enamel is used, the required base material shall be Gilding Metal 95/5 (UNS Alloy C-210). TIOH HARD ENAMEL COLOR CHIPS COLOR CHIP NUMBER Blue #18 ATTACHING DE

6、VICE: The attaching device shall be a prong clutch type as follows. 1. -1 shall have three prongs and clutches. One prong shall be located on the vertical center line 3/16 inch + 1/32 inch below the top of the insignia and one prong in each of the lower corners 3/16 inch + 1/32 inch in from the side

7、s and up from the bottom. 2. -2 and -3 shall have two prongs located on the vertical center line of the insignia, equidistant from each end and 3/4 inch + 1/32 inch apart. NOTES: 1. The term (REF) refers to the measurements taken from the obverse Government furnished hub or die. 2. -2 and -3 are ide

8、ntical with the exception of a plastic back plate which is added to designate JROTC. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - IH Army -

9、 IH Air Force - 11 Review activity: (Project No. 8455-2013-120) DLA - CT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/8F Page 3 of 3 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ARMY

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1