1、 AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET INSIGNIA, RANK, WARRANT OFFICER WO1 AND CHIEF WARRANT OFFICERS CW2, CW3 AND CW4, U.S. ARMY This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product describ
2、ed herein shall consist of this specification sheet and the latest issue of MIL-DTL-14639. DASH NO. -1: Warrant Officer WO1, Regular -5: Warrant Officer WO1, Subdued -2: Chief Warrant Officer CW2, Regular -6: Chief Warrant Officer CW2, Subdued -3: Chief Warrant Officer CW3, Regular -7: Chief Warrant
3、 Officer CW3, Subdued -4: Chief Warrant Officer CW4, Regular -8: Chief Warrant Officer CW4, Subdued MATERIAL: -1 through -4: Gilding Metal -5 through -8: Red Brass or Zinc Aluminum INCH-POUND MIL-DTL-14639/42B 30 June 2010 SUPERSEDING MIL-DTL-14639/42A 30 January 1998 Provided by IHSNot for ResaleNo
4、 reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14639/42B Page 2 of 2 FINISH: -1 through -4: Hard Enameled, Nickel Plated, Mirror-like Polished, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16. -5 through -8: Dull Flat Olive Drab Enamel Finish,
5、 and the area indicated “Enamel” shall match TIOH Metal Finish Chip Number 21. DIMENSIONS: HEIGHT (overall): 1-1/8 inches (REF) WIDTH (overall): 3/8 inch (REF) THICKNESS (overall): 0.065 inch + 0.005 inch NOTES: 1. The term (REF) refers to measurements taken from the Government furnished hub or die.
6、 2. Attaching device shall be prong and clutch type. Prongs shall be located on the horizontal center line, equidistant from each end and 7/8 inch + 1/64 inch apart. 3. Enameled areas shall be as indicated. 4. Enamel color for Dash No. -1 through -4 shall be Black and shall match TIOH Hard Enamel Co
7、lor Chip Number 26. 5. Enamel color for Dash No. -5 through -8 shall be Green (Olive Drab) and shall match FED-STD-595 Color Chip Number 34096. 6. Epoxy resin (stoning epoxy) may be used in lieu of hard enamel at the option of the manufacturer. 7. The insignia shall be dapped on the horizontal plane
8、 to a 5 inch + 1/64 inch radius. 8. Dash No. -1 through -4 may be Rhodium Plated with a Mirror-like Polished Finish at the option of the manufacturer. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were
9、made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationshi
10、p to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Review activity: (Project No. 8455-2010-337) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
