1、INCH-POUND MIL-DTL-3943/13J 15 February 2009 SUPERSEDING MIL-DTL-3943/13H 29 May 2007 DETAIL SPECIFICATION SHEET DECORATION, LEGION OF MERIT, OFFICER AND LEGIONNAIRE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring th
2、e product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3943. DASH NO. -1: Regular Size MATERIAL: Gilding Metal -2: Miniature Size FINISH: OBVERSE: Hard Enameled, Gold Plated, Matte Finish and shall match The Institute of Heraldry (TIOH) Metal Finish Chip
3、 Number 7. REVERSE: Gold Plated, Matte Finish, Polished Highlights and shall match TIOH Metal Finish Chip Number 8.AMSC N/A Page 1 of 3 FSC 8455 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/13J DIMENSIONS: DIAMETER: -1: 1-7/8 inches (
4、REF) -2: 15/16 inch (REF) HEIGHT (including lug): -1: 2 inches (REF) -2: 1 inch (REF) THICKNESS (overall): -1: 0.215 inch 0.010 inch -2: 0.140 inch 0.010 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. No piercing required. 3. Enamel colors
5、 shall be as indicated. The colors shall conform to the TIOH Hard Enamel Color Chip Numbers listed below. The white enameled areas in the five (5) rays on the obverse side of the pendant shall be convex within the dikes. COLOR CHIP NO. Red 4 Green 11 Blue 20 White 28 4. Epoxy resin (stoning epoxy) m
6、ay be used in lieu of hard enamel at the option of the manufacturer. When epoxy resin is used in lieu of hard enamel, the material requirement shall be gilding metal or red brass. 5. The center portion of the reverse of the pendant shall be smooth, flat, and suitable for engraving. 6. The finished p
7、endant ribbon length for Dash No. 1 shall be 1-7/8 inches 1/8 inch. 7. The design of the Officer and Legionnaire are identical except the Officer shall have the 3/4 inch diameter pendant ribbon device conforming to MIL-DTL-41819/2 centered on the pendant ribbon as shown. 8. The service ribbon for th
8、e Legion of Merit, Officer shall have the 3/8 inch diameter pendant ribbon device conforming to MIL-DTL-41819/2 centered on the service ribbon. 9. On an optional basis, the lug may be fabricated with one end an integral part of the pendant. Care should be taken that no sharp edges result from the be
9、nding and closure operation. Page 2 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/13J Page 3 of 3 10. Decoration set shall consist of a regular size medal, a service ribbon, and a lapel button all packaged in a presentation case c
10、onforming to MIL-C-14633, Type VIII, Style 6 with a Class 1, 1A or 3 pad. 11. The ribbon for the pendant drape and service ribbon shall conform to MIL-DTL-11589/80. 12. The lapel button shall conform to MIL-DTL-11484/10. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with
11、vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the
12、 entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - IH Army - IH Air Force 11 (Project No. 8455-2009-043) Navy - NU Review activities: Air Force - 99 Navy - MC Coast Guard - CG DLA CT NOTE: The activities listed a
13、bove were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
