1、 MIL-DTL-50512A 1 February 2010 SUPERSEDING MIL-M-50512 (MU) 29 February 1972 DETAIL SPECIFICATION MINE, APERS, PRACTICE, M68 ASSEMBLING AND PACKING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification prescribes
2、the requirements and identifies the verification procedures for the Mine, APERS, Practice, M68. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 or 4 of this specification. This section does not include documents cited in other sections of this sp
3、ecification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, or 4 of this specification, whether or not the
4、y are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or
5、 contract. AMSC N/A FSC 1345 DISRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUNDComments, suggestions, or questions on this document should be addressed to: Commander, U.S. Army ARDEC, ATTN: RDAR-QES-E, Picatinny Arsenal, New Jersey 07806-5000 or e-mailed to a
6、rdecstdznconus.army.mil. Since contact information can change, you may want to verify the currency of this information using ASSIST Online database at http:/assist.daps.dla.mil. Inactive for new design after 19 August 1997 Provided by IHSNot for ResaleNo reproduction or networking permitted without
7、license from IHS-,-,-MIL-DTL-50512A 2 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1916 - DoD Preferred Methods for Acceptance of Product MIL-STD-1168 - Ammunition Lot numbering and Ammunition Data Card (Copies of these documents are available online at http:/assist.daps.dla.mil or from the Standardizati
8、on Documents Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specifi
9、ed, the issues of these documents are those cited in the solicitation or contract. U.S. ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) DRAWINGS 9251503 - Mine, APERS, Practice, M68 8800900 - Packing and marking for Box, Wirebound for Mine, APERS, M18A1 w/Accessories or Mine, APER
10、S, Practice, M68 or MCCM, M5 w/Accessories 8800901 - Packing and Marking for Box, Fiberboard for Mine, APERS, M18A1 or Mine, APERS, Practice, M68 or MCCM w/Accessories, M5 or M5A1 (Copies of these drawings are available from U.S. Army ARDEC, ATTN: RDAR-EIS-PE, Picatinny, NJ 07806-5000, or email pica
11、.Drawing.Requestconus.army.mil.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws
12、 and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample of the Practice Mine Assembly shall be subjected to first article inspection in accordance with 4.3. 3.2 Conformance inspection. A sample shall be subjected to confor
13、mance inspection in accordance with section 4.4. 3.3 Assemblies. The assemblies shall comply with all requirements specified on Dwg. 9251503. 3.4 Ammunition lot numbering. Ammunition lot numbers shall be assigned in accordance with MIL-STD-1168. Provided by IHSNot for ResaleNo reproduction or networ
14、king permitted without license from IHS-,-,-MIL-DTL-50512A 3 3.5 Workmanship. All mines and accessories shall be free of burrs, sharp edges, cracks, dirt, grease, rips, rust and other foreign matter. Colors shall be uniform. All required markings shall be neat and sharply defined. All packing compon
15、ents shall be dry. 4. VERIFICATION TABLE I. Requirement / Verification cross reference matrix Methods of Verification Classes of Verification 1 Analysis A First Article 2 Demonstration B Conformance 3 Examination 4 Test Section 3 Requirements Description Verification Method Verification Class Sectio
16、n 4 Verification Method 1 2 3 4 A B 3.1 First article inspection X X 4.3 3.2 Conformance inspection X X X 4.4 3.3 Assemblies X X X 4.4.2.1 through 4.4.2.5 3.4 Ammunition lot numbering X X X 4.5.1 3.5 Workmanship X X X 4.5.2 4.1 Classification of inspection. The verification requirements specified he
17、rein are classified as follows: a. First article inspection (see paragraph 4.3) b. Conformance Inspection (see paragraph 4.4) 4.2 Inspection conditions. Unless otherwise specified, all inspections shall be performed in accordance with the test conditions specified herein. 4.3 First article. When spe
18、cified, a sample of the training assembly and subcomponents shall be subjected to first article inspection in accordance with Table II. 4.3.1 First article quantity. The first article sample shall consist of the following items in sample quantities as indicated in Table II. 4.3.2 First article rejec
19、tion. If any assembly, component or test specimen fails to comply with requirements, the first article sample shall be rejected. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 4 TABLE II. First article tests and inspection. Examinatio
20、n or Test No. of Sample Units Requirement Paragraph Paragraph Reference/ Inspection Method MINE, APERS, PRACTICE M68 (Dwg. 9251503) Examination of defects 12 3.3 4.4.2.1 Carton, prior to sealing (Dwg. 8800901) Examination of defects 12 3.3 4.4.2.2 Carton, sealed (Dwg. 8800901) Examination of defects
21、 12 3.3 4.4.2.3 Bag, packing (Dwg. 8800900) Examination of defects 12 3.3 4.4.2.4 Wood packing box (Dwg. 8800900) Examination of defects 12 3.3 4.4.2.5 4.4 Conformance inspection. 4.4.1 Lot formation. Lot formation shall be in accordance with MIL-STD-1916. In addition, each inspection lot of M68 ass
22、emblies shall be produced with components complying with the following constraints: 4.4.1.1 Part no. 9251503-1. a. M33 practice mine from not more than one lot interfix number from one manufacturer. b. M7 bandoleer from not more than one lot interfix number from one manufacturer. c. M10 practice bla
23、sting cap assembly from not more than one lot interfix number from one manufacturer. d. M57 firing device assembly from not more than one lot interfix number from one manufacturer. e. M40 electrical test set assembly from not more than one lot interfix number from one manufacturer. 4.4.1.2 Part no.
24、9251503-2. a. M33 practice mine from not more than one lot interfix number from one manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 5 b. M7 bandoleer from not more than one lot interfix number from one manufacturer. c. Mi
25、ni-det assembly from not more than one lot interfix number from one manufacturer. 4.4.2 Classification of characteristics. a. Sampling requirements. Inspection sampling requirements for critical, major, and minor characteristics are defined in MIL-STD-1916, Table I and Table II. Critical characteris
26、tics shall be addressed in accordance with MIL-STD-1916. Unless specified otherwise, Major Characteristics shall be Level III, and Minor characteristics shall be Level II. b. Conformance inspection. Conformance inspection shall be performed in accordance with section 4.4.2.1 through 4.4.2.5. Provide
27、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 6 Paragraph 4.4.2.1 Title MINE, APERS, PRACTICE M68 Drawing Number 9251503 Category Examination or Test No. of Sample Units Verification Level Requirement Paragraph Paragraph Reference / Inspect
28、ion Method Critical None defined Major 101 Mine or accessory missing III 3.3 Visual 102 Mine or accessory damaged III 3.5 Visual 103 Mine or accessory incorrectly packed III 3.5 Visual Minor201 Poor workmanship II 3.5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted withou
29、t license from IHS-,-,-MIL-DTL-50512A 7 Paragraph 4.4.2.2 Title Carton, prior to sealing Drawing Number 8800901 Next Higher Assembly 8800900 Category Examination or Test No. of Sample Units Verification Level Requirement Paragraph Paragraph Reference / Inspection Method Critical None Defined Major 1
30、01 Number of field packs incorrect III 3.3 Visual 102 Packing components missing III 3.3 Visual Minor None Defined Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 8 Paragraph 4.4.2.3 Title Carton, sealed Drawing Number 8800901 Next Hig
31、her Assembly 8800900 Category Examination or Test No. of Sample Units Verification Level Requirement Paragraph Paragraph Reference / Inspection Method Critical None Defined Major 101 Contents move when carton is shaken (insufficient filler material) III 3.3 Visual & Manual 102 Contents damaged so th
32、at contents are exposed or liable to be exposed III 3.5 Visual Minor201 Marking improper or unidentifiable II 3.5 Visual 202 Evidence of poor workmanship II 3.5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 9 Paragraph 4.4.2.4
33、 Title Bag, packing Drawing Number 8800901 Next Higher Assembly 8800900 Category Examination or Test No. of Sample Units Verification Level Requirement Paragraph Paragraph Reference/ Inspection Method Critical None Defined Major 101 Bag ruptured, punctured, or seal incomplete III 3.5 Visual & Manual
34、 Minor 201 Heat seal incorrectly located II 3.3 Visual202 Air not removed from bag II 3.5 Manual 203 Marking improper or unidentifiable II 3.5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 10 Paragraph 4.4.2.5 Title Wood packi
35、ng box Drawing Number 8800900 Category Examination or Test No. of Sample Units Verification Level Requirement Paragraph Paragraph Reference / Inspection Method Critical None Defined Major 101 Box damaged to the extent that contents are exposed or liable to become exposed III 3.3 Visual 102 Strapping
36、 or hardware missing, broken, or loose III 3.5 Visual & Manual Minor 201 Hardware on strapping improperly assembled or engaged II 3.5 Visual202 Contents loose II 3.5 Manual 203 Case seal missing, unsealed, or improperly positioned II 3.5 Visual204 Marking improper or unidentifiable II 3.5 Visual Pro
37、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 11 4.5 Methods of inspection. 4.5.1 Ammunition lot numbering. Visually verify that ammunition lot number has been applied to each lot as described in MIL-STD-1168. 4.5.2 Workmanship. Visuall
38、y verify that all parts and assemblies meet requirements of 3.5. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house personnel, these personnel n
39、eed to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system command. Packaging data retrieval is a
40、vailable from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended
41、use. The Mine, APERS, Practice M68 with accessories is an anti-personnel mine inert used in training personnel. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number and date of this specification. b. Applicable stock number. c Packaging requirements, if
42、other than specified in Section 5. d Serialization requirements, if applicable. e. Certificate of conformance for each lot or shipment of product. 6.3 Drawings. Drawings listed in section 2 of this specification under the heading U.S. Army Armament, Research, Development and Engineering Center (ARDE
43、C) may also include drawings prepared by, and identified as U.S. Army Armament, Research and Development Command (ARRADCOM), Frankford, Rock Island, or Picatinny drawings. Technical data originally prepared by these activities is now under the cognizance of ARDEC. 6.4 Submission of inspection equipm
44、ent designs for approval. Submit equipment designs as required to Commander, ARDEC, ATTN: RDAR-QEM-G, Picatinny, NJ 07806-5000. In addition, inspection equipment used for acceptance of product should be capable of repeatable measurements, by various experienced inspection/test personnel, to an accur
45、acy of 10% of the Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-50512A 12 total tolerance of the characteristic being inspected. This inspection requirement should also be specified in the contract. Request letter of submittal should state
46、contractor, contract number, specification number, item nomenclature and classification of defects or test paragraph, inspection equipment, inspection method, accuracy of equipment, and the frequency of inspection should be submitted for approval to Commander, ARDEC, ATTN: RDAR-QEM-G, Picatinny, NJ
47、07806-5000. 6.5 Submission of alternative conformance provisions. All contractor proposed alternative conformance provisions will be submitted to the Government for evaluation/approval as directed by the contracting activity. Submit equipment designs as required to Commander, ARDEC, ATTN: RDAR-QEM-G
48、, Picatinny, NJ 07806-5000. 6.6 Automated acceptance inspection equipment. Equipment for which no, or minimal, human involvement is required in the acceptance determination. This would include equipment employing probes/sensors/transducers that are automatically manipulated to perform measuring and detection functions. If readout is provided, the equipment will be categorized as automated even if operator interpretation is needed in the accept/reject decision. 6.7 Subject term (key word) listing. Claymore Claymore Mine Firing Device
