1、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CCC-D-950 - Dyeing and Aftertreating Processes for Cotton PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner PPP-B-636 - Box, Shipping, Fiberboard MIL-T-3530 - Thread and Twine, Mildew-Resistant or Water-
2、MIL-P-15328 - Primer (Wash) Pretreatment, Blue, (Formula MIL-G-16491 - Grommet, Metallic Cloths MILITARY Re pe 1 1 ant Treat ed No. 117-B for Metals) STANDARDS FEDERAL FED-STD-191 - Textile; Test Methods FED-STD-595 - Colors FED-STD-751 - Stitch; Seam and Stitching MIL-STD-105 - Sampling Procedures
3、and Tables for Inspection MIL-STD-129 - Marking for Shipment and Storage MIL-STD-1363 - Measurement of Wood Moisture Content MILITARY by Attributes DRAWINGS THE INSTITUTE OF HERALDRY 5-1-337 - Flag Set, M-133 (Figure 1 is a miniature copy of the referenced drawing and is attached for informat ion on
4、ly. ) (Copies of specifications, standards and drawings required by contractors in connection with specific procurement functions should be , obtained from the procuring activity or as directed by the contracting 2.2 Other publications.- The following publication forms a part of this specification.
5、Unless othewise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. THE COLOR ASSOCIATION OF THE UNITED STATES, INC. U.S. Army Color Card, The Official Colors for Branches, Agencies, Etc. (Applications for copies of the color card shall be addressed to
6、The Color Association of the United States, Incorporated, 200 Madison Avenue, New York, New York 10016.) 3. REQUIREMENTS 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without li
7、cense from IHS-,-,-I Por sewing the cotton - Ticket No. 24, 4 ply; duck head ing type IB1 for needle and type IA1 for bobbin. For hemming the flag - Ticket No. 24, 4 ply; type IB3 for needle and type IA3 for bobbin. I 3.4.3.1 Color and treatment.- The thread used for hemming the flag shall be dyed o
8、range to match the color of the flag. When tested as specified in 4.3.1.1, the fastness to light, laundry, and bleaching shall be equal to, or bettes than, the standard. When no standard sample is available, the fastness to light, laundry, and bleaching shall be good. The thread for sewing the cotto
9、n duck heading shall be natural in color. All thread shall be mildew-resistant treated in accordance with type I, Class i or 2 of MIL-T-3530. 3.4.4 Color matching o textile material.- The dyed textile components shall be matched for color prior to the application of the mildew-resistant treatment. T
10、he color of the finished material resulting from the application of the mildew-resistant treatment shall be acceptable provided the color match is acceptable before treatment is applied . 3.4.5 - Wood.- The wood for the flagstaff handles shall be thorough- ly seasoned and kiln dried. When tested as
11、specified in MIL-STD-1363, the moisture content of the wood shall be 8 to 12 percent. The wood shall be sound and free from surface defects except surface checks not exceeding 1/32 inch in width and sound pin knots not exceeding 118 inch in diameter. Any of the following species shall be acceptable.
12、 Beach Ash Birch Hickory Maple Walnut 3.4.6 Steel.- 3.4.6.1 Steel tubing.- The steel tubing for the staff shall _I- conform to FS 1020, type I, cold drawn of QQ-T-830. 3.4.6.2 Steel, sheet and strip.- The steel for the clips shall conform to PS 1010 to 1020, half hard of QQ-S-698. 3.4.7 - Wire.- The
13、 wire for the split rings shall conform to grade FS 1045 steel wire of QQ-W-461. 3.4.8 Grommet.- Grommets shall conform to type I, class 1, size O 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.9 Enamel.- The enamel for the staff shall be a se
14、mi-gloss, air drying enamel conforming to TT-E-529. The color shall be olive drab conforming to Color No. X24087 of FED-STD-595. 3.4.10 Primer.- Primer for the metal components shall conform to TT-P-636 and pretreatment primer shall conform to MIL-P-15328. 3.5 Components.- The flag set shall consist
15、 of two components, the MG-129 flag and the MC-130 flagstaff. Assembly shall be as shown on drawing 5-1-337. 3.6 Construction,- The flag set shall be constructed in accordance with the details and dimensions of drawing 5-1-337 and the requirements spec if ied herein. 3.6.1 Stitching.- All stitching
16、shall be accomplished using thread specified in 3.4.3. The stitching shall conform to FED-STD-751. All stitching shall be type 301 with 8 to 10 stitches to the inch on the flag hems and 6 to 8 stitches to the inch on the flag heading. All stitching ends not otherwise covered or locked shall be backs
17、titched 1/2 inch. Stitching breaks shall be overstitched for a distance of 1 inch. 3.6.2 Welding.- The welds shall be sound, smooth and laid on in such a manner to insure the metal adjacent to the clips and plugs is not damaged. 3.6.3 Setting of grommets.- The grommets specified in 3.4.8, shall be s
18、et by punching a hole through the material which is smaller than the outside diameter of the grommet barrel and forcing the barrel through the hole, The grommets shall then be securely clinched without cutting or damaging the mat er ia1 . 3.7 Details of components.- 3.7.1 Component A (MC-129, flag).
19、- The flag shall be fabricated from cotton bunting specified in 3.4.1. The fly end and sides shall be hemmed as shown using stitching type EFb-1. The heading shall be fabricated from cotton duck specified in 3.4.2. The cotton duck shall be cut 19-1/2 inches + 1/4 inch long by 4-1/4 inches + 1/8 inch
20、 wide. The long edges shall be folded in 13/16 inch + 1/16 inch. The hoist end of the flag shall then be centered and lapped-in a distance of 1-3/8 inches + 1/8 inch. Che raw ends of the duck shall be folded in over the flag and the duck folded to form a heading 1-3/8 inches + 1/8 inch wide. The hea
21、ding shall be stitched all around with two rows of stitching as shown on drawing 5-1-337. The two rows of stitching shall be 1/8 inch to 3/16 inch apart. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- . . _ I_- MIL-F-qOOSqB 3 - 999990b 0390603 7
22、- MIL-F-4005433 3.7.2 Component B (MC-130, flagstaff).- The flagstaff shall be constructed in accordance with the details and dimensions shown on drawing 5-1-337. Tubing specified in 3.4.6.1, shall be cut to the required length and two steel plugs shall be welded or driven in the ends of the shaft.
23、Clips fabricated from steel specified in 3.4.6.2, and split rings fabricated from wire specified in 3.4.7, shall be located as shown on drawing 5-1-337. The wooden handle shall then be positioned and a steel pin forced through the handle and shaft to lock the handle in position. 3.7.2.1 Wooden handl
24、e.- The handle shall be machined from wood specified in 3.4.5. The finished handle shall have a smooth outer surface and shall be free from checks, splits, knots or any other defect which may effect appearance and serviceability. 3.8 Finish.- 3.8.1 Metal components.- Except for grommets, all metal c
25、omponents shall be finished as specified herein. 3.8.1.1 Plating.- After welding, the tubing, plugs and clips shall be zinc plated in accordance with class 2, type III of QQ-2-325. The split rings and pin shall be zinc plated in accordance with class 2, type I of QQ-2-325. 3.8.1.2 Painting.- After p
26、lating, all metal components shall be primed with primer specified in 3.4.10 and painted with enamel specified in 3.4.9. 3.8.2 Wooden handle.- After marking, the wooden handle shall be water-repellant treated in accordance with type I, composition A of TT-W-572, except the paintability requirement s
27、hall not apply. 3.9 Marking.- 3.9.1 Component A (MC-129 flag).- The flag shall be marked by stenciling or printing “MC-129“ with black ink in the locations shown on drawing 5-1-337. inch in height. The letters and numerals shall be block capitals 1/4 3.9.2 Component B (MC-130 flagstaff).- The flagst
28、aff shall be marked “MC-130“ in block letters and numerals by branding on the handle in the size and location shown on drawing 5-1-337. 3.10 Workmanship.- The flag set or components shall be clean, well made and shall meet the acceptable quality levels established by this specification, 6 Provided b
29、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. NIL-F-400548 83 U 997970b O390602 7 MIL-F-40054B 4. QUALITY ASSURANCE PROVISIONS 4. L Inspection responsibility.- Unless otherwise specified in the Except as contract or purchase order, the supplier is responsi
30、ble for the performance of all inspection requirements specified herein. atherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. inspections
31、set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to the prescribed requirements. The Government reserves the right to perform any of the 4.2 First article inspection.- Inspection and testing of the first article shall be made on a com
32、pletely finished item for all provisions applicable to the end product examination and tests. 4.3 Sampling for inspection- and acceptance.- Sampling for inspec- tion an acceptance shall be in accordance with the provisions set forth in MIL-STD-105, except where otherwise indicated. 4.3.1 Inspection
33、of components.- 4.3.1.1 Testing of components.- In addition to the quality assurance provisions of the subsidiary specifications and standards, inspection shall be performed on components and materials listed in table I for the characteristics shown therein. The inspection level shall be S-1 and the
34、 AQL shall be 6.5 defects per hundred units. Requirements are applicable to the individual unit. specified in FED-STD-191. TABLE I Textile tests are Component and material testing.- s/u Component Characteristic Rqmt Test #determ Results and unit para. method per s/u reported as product Dyed Colorfas
35、tness : cloth, To light 3.4.1.1 5660 1 Satisfactory 3“ X 411 cotton To laundry and 3.4.1.1 5605 1 or unsatis- piece bunting bleaching factory (i 1 inear Thread (1 Colorfas tness : Spool To light 3.4.3.1 5660 1 Satisfactory 1 spool, cone or To laundry and 3.4.3.1 5605 1 or unsatis- cone or tube) blea
36、ching factory tube Wood Mo is t Ure 3.4.5 MIL-STD- 3 Average of 3 1 block yd.) 1363 determ to prior content nearest 1% to Species 3.4.5 Visual 1 Pass or fail turning 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo re
37、production or networking permitted without license from IHS-,-,-9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Class if icat ion Minor Defect Major Examine Heading Any row of required stitching missing Heading not seamed as specified End and edge
38、not closed with two rows of stitching,. . Does not extend full length of the hoist end of flag . One or both missing Insecurely clinched Broken, cracked or otherwise defective affecting function,. One or both clinched too tight cutting surrounding fabric., Rough or sharp edge Marking missing, incorr
39、ect or illegible Printed or stenciled in other than black ink. Outer surface not smooth.,. Any large check, split, crack, torn or raised grain or other defects affecting service- ability or appearance, Any rot, pith, shake, wane or decay Handle tacky to feel . Any burr, sliver or splinter that can c
40、ause injury or damage fabric. Pin missing or loose (not press fit) . Any crystalline, waxy or oily deposit Handle not securely attached to rod Edge of parallel groove not smooth. Design of handle is not as specified . Marking on handle not branded in the size and locations as shown in drawing . Colo
41、r of film not as specified . Scratch, cut, abrasion, etc., with exposure of base metal,. Gouge mark, check, pit, burn, with exposure of base metal,. Foreign debris removal of which would expose base metal.,. . Marking illegible X X X X X x Gr omme t s x - X - X . x Marking Flagstaff , Number 6. NOTE
42、S 6.1 Intended use.- The flag set covered by this specification is intended to be used as signal equipment. 6.2 Ordering data.- Procurement documents should specify the f o1 low ing : (a) Title, number and date of this specification. (b) (cl When only a component is required (see 1.2). When a guide
43、sample will not be furnished (see 3.11, (d) When standard samples will not be furnished (see 3.2). (e) When a first article is not required (see 3.3). (f) Selections of applicable levels of packaging and packing (see 5.1 and 5.2). 6.3 Samples. - Guide samples and standard samples required should be
44、obtained from the procuring activity issuing the invitation for bid. 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ I_ ._l_l_ flIL-F-qO054B 3 M 9999906 0370bLL T - MIL- F- 400 5 4 B “U.S. GOVERNMENT PRINTING OFFICE: 1978 - 603-022/5158 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
