1、. MIL-F-53043 43 m 7777706 0277738 O m a - 237 - 1 o MIL-F-53043(ME) 20 July 1984 SUPERSEDING (see 6.4) MILITARY SPECIFICATION FORWARD AREA WATER POINT SUPPLY SYSTEM This specification is approved for use by the USA Belvoir Research and Development Center, Department of the Army, and is available fo
2、r use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a portable potable water-dispensing system for use in forward areas to provide water to troop elements deployed to remote, “bare base“ desert areas. 2. APPLICABLE DOCUMENTS 2.1 Governmen
3、t documents. 2.1.1 Specifications and standards. Unless otherwise specified (see 6.21, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DODISSI specified in the solicitation, form a part of this specifica
4、tion to the extent specified herein. SPECIFICATIONS FEDERAL TT-W-5 7 2 PPP-B-601 PPP-B-621 PPP-B-6 3 6 MILITARY MIL-C- 104 MIL-P-116 - Wood-Preservation: Water Repellant. - Boxes, Wood, Cleated-Plywood. - Boxes, Wood, Nailed and Lock-Corner. - Boxes, Shipping Fiberboard. - Crates, Wood; Lumber and P
5、lywood Sheathed, - Preservation, Methods of. Nailed and Bolted. Beneficial comments (recommendations, additions, deletions) and any pertinent I data which may be of use in improving this document should be addressed to: USA ,Belvoir Research and Development Center, ATTN: STRBE-DS, Fort Belvoir, VA ;
6、22060-5166 by using the self-addressed Standardization Document Improvement :Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 4320 THIS DOCUMENT CONTAINS 11 PAGES _ - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
7、F-53043 q3 m 7777706 0277717 2 I! ST MIL-B-2 73 MIL-T-704 MIL-P- 7 7 5 MIL-C-1283 MIL-A-8625 MIL-G-20241 MIL-P-23377 MIL-D-43699 MIL-E-52798 MIL-S-81733 NDARDS FEDERAL - Bag, Drinking Water Storage: Cloth, Cotton Duck, Porous. - Treatment and Painting of Materiel. - Packaging of Hose, Hose Assemblie
8、s; Rubber, Dispensing, Plastic, Fabric or Metal (Including Tubing); and Fittings, Nozzles and Strainers. - Can, Gasoline, Military, 5-Gallon. - Anodic Coatings, for Aluminum and Aluminum Alloys. Gasket Material, Wool Felt, Impregnated, Adhesive, Pressure-Sensitive. - Primer Coating, Epoxy-Polyamide
9、Chemical and Solvent Resistant. - Drums, Fabric, Collapsible, Potable Water, 250- and 500-Gallon Capacities. - Pumps, Centrifugal, 2-Inch, Gasoline- or Diesel-Engine Driven. - Enamel, Alkyd, Camouflage, - Sealing and Coating Compound, Corrosive Inhibitive. FED-STD-595 - Colorr MILITARY MIL-STD-105 M
10、IL-STD-129 MIL-STD-889 MIL-STD-1186 - Sampling Procedures and Tables for Inspection - Marking for Shipment and Storage. - Dissimilar Metals. - Cushioning, Anchoring, Bracing, Blocking and by Attributes. Waterproofing: With Appropriate Test Methods. 2.1.2 Other Government documents, drawings, and pub
11、lications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Drawings TA13225E9095 - Forward Area Water Point Supply System. CODE OF FEDERAL REGULATIONS Title 21 - Federal Food, Drug and Cosmetics Food Additive. 2 P
12、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-53043 43 7777706 0277720 7 (The code of Federal Regulations is available from the Superintendent of Documents, US Printing Office, Washington, DC 20402.) (Copies of specifications, standards, and d
13、rawings required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. The issue
14、s of the documents which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D 380 ASTM D 3951 - Standard Practice for Commercial Packaging. - Testing Rubber Hose. (Application
15、for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Industry association specifications and standards are generally available for reference from libraries. using Federal agencies.) They are also distributed among technical gro
16、ups and 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Description. The Forward Area Water Point Supply System (RDF), hereinafter referred to as “FAW
17、PSS“, shall be in accordance with TA13225E9095 and as specified herein. drums, a 125 gpm pumping assembly, suction and discharge hose assemblies, valves nozzles, nozzle stands and necessary ancillary items. The major components of FAWPSS include six 500 gallon 3.1.1 Drawings. The drawings forming a
18、part of this specification are end product drawings. permissible without prior approval of the contracting officer. could cumulatively result in incorrect fits, the contractor shall provide tolerances within those prescribed on the drawings to insure correct fit, assembly, and operation of the FAWPS
19、S. Any data (e.g. shop drawings, layouts, flow sheets, processing, etc.) prepared by the contractor or obtained from a vendor to support fabrication and manufacture of the production item shall be made available, upon request, for inspection by the contracting officer or the designated representativ
20、e. . No deviation from the prescribed dimensions or tolerances is Where tolerances 3.2 First article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 4.3 and 6.3). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
21、-,- MIL-F-53043 43 W 777770b 0277723 O W 3.3 Material. Materials shall be as specified herein and on the drawings. Materials not specified shall be selected by the contractor and shall be subject to all provisions of this specification (see 3.3.2). Materials in contact with potable water shall be ce
22、rtified in accordance with Code of Federal Regulations, Title 21, parts 177 and 182 for rubber compounds in contact with potable water, 3.3.1 Material deterioration and control. The FAWPSS shall be fabricated from compatible materials, inherently corrosion and deterioration resistant or treated to p
23、rovide protection against the various forms of corrosion and deterioration that may be encountered in any of the applicable storage and operating environments to which the FAWPSS may be exposed. 3.3.1.1 Dissimilar metals. Dissimilar metals, as defined in MIL-STD-889, shall be electrically insulated
24、from one another to minimize or prevent galvanic corrosion. corrosion inhibiting sealant conforming to MIL-S-81733 or chromate tape conforming to MIL-G-20241 or a coat of epoxy primer conforming to MIL-P-23377. Protection against corrosion could also be obtained by exclusion of the electrolyte if fe
25、asible. Insulation may be provided by an insulating barrier such as a 3.3.1.2 Identification of materials and finishes. The contractor shall identify the specific material, material finish or treatment for use with components and sub-components, and shall make information available, upon request, to
26、 the contracting officer or designated representative, 3.3.2 Recovered materials. For the purpose of this requirement, recovered materials are those materials which have been collected from solid waste and reprocessed to become a source of raw materials, as distinguished from virgin raw materials. T
27、he components, pieces and parts incorporated in the FAWPSS may be newly fabricated from recovered materials to the maximum extent practicable, provided the FAWPSS produced meets all other requirements of this specification. Used, rebuilt or remanufactured components, pieces and parts shall not be in
28、corporated in the FAWPSS. 3.4 Components. The sizes, types, lengths and quantities of components shall be as specified under TA13225E9095 and herein, 3.5 Treatment and painting. 3.5.1 Painted finish. Unless otherwise specified (see 6.21, the portions or components of the FAWPSC normally painted shal
29、l be cleaned, treated and painted in accordance with MIL-T-704, type A, with the finish coat in accordance with MIL-E-52798, type I, color sand. 3.5.2 Aluminum finish. Unless otherwise specified (see 6.2), aluminum component surfaces shall be anodized and dyed in accordance with MIL-A-8625, type II,
30、 class 2, sealed, color to conform to FED-STD-595 color number 30277, sand matte, as closely as is practical to achieve. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-530q3 43 7777906 O277722 2 MIL-F-53043 (ME) 3.5.3 Non-metallic finish. Un
31、less otherwise specified (see 6.2) nonmetallic components (u hose) shall conform in color FED-STD-595 color number 30277, sand matte, as closely as is practical to achieve. 3.6 Government-furnished property. Unless otherwise specified (see 6.2). The following property in the quanities indicated will
32、 be furnished by the Government (see 6.5). Item No. Description 1 Adapter assembly, fuel drum. 2 Bag, drinking water storage. 3 Can, gasoline military. (5 galion) 4 Drum, fabric, collapsible, Potable water, 500 gallon capacity, size II. 5 Pump, centrifugal, 2-in., cl.1 or Pump, centrifugal, 2-in., c
33、1.3. Identification Quantity for each FAWPSS NSN 2910-00-066-1235 1 NSN 4610-00-268-9890 2 NSN 7240-00-222-3088 2 NSN 8110-01-122-0015 6 (MIL-B-273) (MIL-C-1283) (MIL-D-43699) NSN 4320-00-542-3347 1 (MIL-P-52109 NSN 4320-01-156-3873 (MIL-P-52109) 3.7 Identification markings. The components of the FA
34、WPSS shall be identified in accordance with their respective drawing or procurement specification. 3.7.1 Special markings. The following components, 500 gallon drum and 125 gpm pump shall be marked with the words “drinking water“ or “drinking water only“ in blue letters in accordance with FED-STD-59
35、5, color number 25102 as closely as is practical to achieve. 3.8 Workmanship. All parts, components, and assemblies of the FAWPSS shall be clean and free from extraneous material and in accordance with the workmanship requirements of the component specification referenced herein. 4. QUALITY ASSURANC
36、E PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use
37、his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure
38、 supplies and services conform to prescribed requirements. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I _ - MIL-F-53043 43 9 797770b 0277723 4 4.1.1 Responsibility for compliance. All items must meet all section 3 and 5 requirements. demonstra
39、te compliance. authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The inspections in section 4 are the minimum to be used to Sampling in quality conformance inspection does not 4.1.2 Component and mater
40、ial inspection. The contractor is responsible for insuring that components and materials are manufactured, examined, and tested in accordance with referenced specifications and standards, as applicable. 4.2 Classification of inspections. The inspection requirements specified herein are classified as
41、 follows: a. b. C. First article inspection (see 4.3). Quality conformance inspection (see 4.4). Inspection of packaging (see 4.6). 4.3 First article inspection. 4.3.1 First article examination. The first article shall be examined as specified in 4.5.1 in the order shown. cause for rejection. Presen
42、ce of one or more defects shall be o 4.3.2 First article test. The first article shall be tested as specified in 4.5.2 in the order shown. Failure of any test shall be cause for rejection. 4.4 Quality conformance inspection. 4.4.1 Sampling. Sampling for examination and tests shall be in accordance w
43、ith MIL-STD-105. 4.4.2 Examination. Samples selected in accordance with 4.4.1 shall be examined as specified in 4.5.1. AQL shall be 2.5 percent defective. 4.4.3 Tests. Samples selected in accordance with 4.4.1 shall be tested as specified in 4.5.2. AQL shall be 2.5 percent defective. 4.5 Inspection
44、procedure. 4.5.1 Examination. The FAWPSS shall be examined as specified herein for the following defects: 101. 102. 103. 104. 105. 106. 107. 108. 109. Certification that material in contact with potable water is in accord- ance with current applicable standards governing the handling of potable wate
45、r not furnished (see 3.3). Materials not as specified. Material not resistant to corrosion and deterioration or treated to be made resistant to corrosion and deterioration. Dissimilar metals not in accordance with MIL-STD-889. Components size, type and quantity not as specified. Treatment and painti
46、ng not as specified. Metallic components finish not as specified. Identification markings and special markings not as specified. Workmanship not as specified. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-F-53043 43 m 7q9770b 0277724 b m 4.5
47、.2 Test. 4.5.2.1 Component test. - 4.5.2.1.1 Government-furnished property. When the components are other than Government furnished (see 3.61, each component shall be tested and accepted in accordance with the requirements of the applicable components specif icat ion. 4.5.2.1.2 Drawing specified com
48、ponents. Unless otherwise specified (see 6.2), each component shall be tested and accepted in accordance with the requirements of the applicable component specification reference on the drawings. 4.5.2.1.3 Hose assemblies. Each hose assembly complete with couplings shall be subjected to hydrostatic
49、test pressure of 100 psi in accordance with ASTM D 380,-except that the pressure shall be maintained for two minutes. blistering or leaking of the hose shall be cause for rejection. Any 4.5.2.2 FAWPSS functional system test. The FAWPSS shall be assembled as shown in drawing TA13225E9095 with the drums filled with water, the pump assembly started and operated until the drums are empty. test, the entire system shall be examined for leaks. Each valve and nozzle s
