1、I I“-PoUND I MIL-H-44098A 17 January 1990 Super sed ing 10 March 1983 MIL-H-44098 MILITARY SPECIFICATION HEADBAND, GROUND TROOPS - PARACHUTISTS HEINJTT! This specification is approved for use by all Dspartments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This specification covers
2、one type of headband for the ground treopsl-parachutists helmet (see 6.1). 1.2 Classification. The headband assably shall be of the following sizes as specified (see 6.2) , X-mal 1 (XS) Small - Medium - Large X-Large (S-M-L) 2. APPLICABLE DOCUMENTS 2.1 Goverment documents. Beneficial ccm-unentc (rec
3、ammendations, additions, deletions) and any pertinent data whichmay be of use in improving this document should be addressed to: and Engineering Center, Natkk, MA 01760-5014, by using the self-addressed Standardization Document mprovement Proposal (DD Form 1426) apparing at the end f this document o
4、r by letter. U,S, Amy Natick Research, Developnent, AMSC N/A FSC 8470 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-44038A 4 777770b 0366478 2 MIL-H-44098A 2.1.
5、1 Specifications, standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the Department of Defense Index of Specifications and Standards
6、 (DODISS) and supplement thereto, cited in the solicitation. (see 6.2) SPECIFICATIONS FEDERAL A-A-50083 PPP-B-636 - Boxes, Shipping, Fiberboard PPP-T-45 - Bag, Plastic, Folded Garment - Tape, Gumned, Paper. Reinforced and Plain, for Sealing and Securing MILITARY MIL-L-35078 - Loads, Unit: Preparatio
7、n Of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage, General Specification For STANDWS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipnent and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Me
8、mbers For Containers and Pallets by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, BLDG 4D, 700 Robbins Avenue, Philadelphia, PA 19120-5094.) 2.1.2 Other Government documents,
9、 drawings, and publications. The following other Govermnt documents, drawings, and publications form a part of this document to the extent specified herein. issues are those cited in the solicitation. Unless otherwise specified, the DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CE
10、NTER 2-1-1384 - Headband, Ground Troops - Parachutists Helmet 2-1-1385 - Clip, Spring, Headband (Copies of drawings are available fran the U.S. Amy Natick Research, Development and Engineering Center, ATTN: STRNC-EMSS, Natick, MA 01760-5014.) 2 c Provided by IHSNot for ResaleNo reproduction or netwo
11、rking permitted without license from IHS-,-,-MIL-H-44078A 84 M 7777906 0366477 4 W MIL-H-44098A 2.2 Non-Goverriment publications. The following document forms a part of this document to the extent specified herein. Unless otherwise smcified. the issues of the documents which-are DOD adopted are thos
12、e listed in-the issue of the DODISS citei in the solicitation. of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, the issues AMERICAN SEIETY FOR TESTING AND MATERIALS (ASTM) B 3951 - Standard Practice for Commercial
13、Packaging (Application for copies should be addressed to the Elnierican Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Goverment standards and othei: publications are normally available from the organizations that prepare or distribute the documents. also may
14、 be available in or through libraries or other informational services.) These documents 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes app
15、licable laws and regulations unless a specific exemption has been obtained. 3.1 First: aiticle. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3, 3.2 Guide sample. Guide samples, when furnished are solely for guidance and infomacontra
16、ctor (see 6.4). may appear in the smple in which case this specification shall govern. Variations from this specification 3.3 blaterials and cmpnents. The materials and cmponents used shall confsmencxA specifications, standards, an recjyirmen%a specifid herein. they shall be of the quality normally
17、used for the purpose in coiranercial pEaetice povidd the completed itarts camply with all provisions of this specification. as long as itmeeta the KEXEETRES sf this specification. Where materials are not definitely specified, t is encouraged %hat recycled material k used when practical 3.3-1 Identif
18、ication marlning, A white paper label with legible and durable black mar- inside the polyethylene bag specified in 5.1.1 so that the label can be read through the bag. commercial quality white writing OE printing paper, having a minimum basis weight of 20 pounds (17 x 22/50). information: The label
19、paper shall be made of The paper label shall contain the following Item description (approximately 1/4 inch) Contract number (approximately 1/4 inch) Stock n edge Any end not fused 202 101 201 scalloped Fastener tape Any hole, cut, or tear 102 Leather Any hole, cut, or tear 103 Finish chipped, flaky
20、, cracked, 104 or ani tted 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-4407A 4 m 7799906 03bb43 b MIL-H-44098A TABLE I, End iten visual defects (contld) Classification Major Minor Examine Defect Leather (contl d) 105 Any imperfection that
21、 would cause discomfort to the wearer such as: hard area, scar tissue, or lumps Grain surface of leather not facing outs ide Deep scratch, crack, heavy vein, pit, or abraded area 106 203 Hardware Seams and stitching: Open seams Note: Runoffs Seam and stitch type Stitch tension Stitches per inch Brok
22、en or malformed, failing to serve intended purpose; finish omitted, corroded area, burr, or sharp edge Buckle not attached in orientation specified in Drawing 2-1-1384 Any clip not attached as specified One half inch or less More than 1/2 inch A seam shall be classified as open when one or more stit
23、ches joining a seam are broken or when two or more consecutive skipped or runoff stitches occur. (See “Open seams“) Wrong seam or stitch type Loose, resulting in loose bobbin or top thread Excessively tight, resulting in puckering of material or cutting of leather between needle holes One stitch les
24、s than minimum specif ied Two or more stitches less than minimum specif ied One or more stitches in excess of maximum specified 7 107 108 204 205 109 U 110 206 207 208 111 209 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-44098A TABLE I. n?d
25、iten visual defects (contd) Classification Examine Defect Major Minor Seas and stitching Stitching ends Thread breaks, skipped stitches or runoffs Note: Rows of stitching Components and assembly -0 Identification marking Cleanness (cont d) Ends of stitching not secured as specified (except when caug
26、ht in other stitching) Overstitched less than 1/2 inch in each direction beyond the defective stitching area Thread.breaks or two or more consecutive skipped or runoff stitches not overstitched shall be classified as open seams. Any row omitted Any required cmponent or operation omitted (unless othe
27、rwise classified herein) Any component misplaced or not assanbled as specified (unless otherwise classified herein) Loop pile fastener tape not attached with loop pile facing the leather Color of any component not as specified Needle chews Any unauthorized repair Qnitted, illegible, or incorrect Spo
28、ts or stains clearly noticeable Thread ends not triirsned throughout as specified 210 211 112 113 114 115 212 116 117 213 214 215 4.4.4 End item dimensional examination. The end items shall be examined for Only those dimensions conformance to the dimensions specified on the drawings. that can be eva
29、luated without damaging OK disassembling the end items shall be examined. as a defect. sample unit shall be one headband. AQL, expressed in tem of defects per hundred units, shall be 4.0. Any dimension not within the specified tolerance shall be classified The lot size shall be expressed in units of
30、 headbands. The “he inspection level shall be S-3. The 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGH-44098A 4.4.5 Packaging examination. The fully packaged end itens shall be examined for the defects listed below. shipping containers. packag
31、ed. defects per hundred units, shall be 2.5. The lot size shall be expressed in units of The sample unit shall be one shipping container fully The inspection level shall be S-2. The AQL, expressed in terms of Examine Defect Marking (exterior mitted; incorrect; illegible; of improper size; and interi
32、or) location, sequence, or method of application Materials Workmanship Content Any component missing, damaged, or not as specif i incorrect; illegible; of improper size, location, sequence, or method of application 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commercial, as specif
33、ied (see 6.2). 5.1.1 Level A preservation. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-44098A 5.1.1.1 Unit packing. Each headband shall be folded once at the approximate midpoint of the leather component and with the leather facing to the
34、 outside. The free end of the nylon webbing shall be folded under resulting in a assembly approximately 10 inches long. The folded headband along with the paper label specified in 3.3.1 (with the marking facing the outside of the bag) shall be inserted in a plastic bag conforming to A-A-50083. 5.1.1
35、.2 Intermediate packing. Two hundred headbands, of one size only, unit packed as specified in 5.1.1.1, shall be packed on edge four in length, one in width, and five in depth in an intermediate fiberboard box conforming to style RSC, type CF (variety SW), class domestic, grade 200 of PPP-B-636. Appr
36、oximate inside dimensions of each intemediate box shall be as specified in table II. Box closure shall be effected with 2-inch minimum width gummed paper tape conforming to type III, grade B of PPP-T-45. TABLE II. Approximate inside dimensions of intermediate box and shipping container - i/ intermed
37、iate box Shipping container (inches) (inches) -.I 20 x 10-1/2 x 5 20-1/2 x 15-1/2 x 11 - i/ Approximate inside dimensions are furnished as a guide only with ASTM D 3951. 5.1.2 Commercial preservation. Headbands shall be preserved in accordance 5.2 Packing. Packing shall be level A, B, or Cornmercial
38、 as specified (see 6.2). 5.2.1 Level A packing. Six hundred headbands of one size only, preserved as specified in 5.1, shall be packed in a fiberboard shipping container conforming to style RSC, grade V2s of PPP-B-636. of each shipping container shall be as specified in table II. Each shipping conta
39、iner shall be closed in accordance with method III, waterproofed in accordance with method V, and reinforced as specified in the appendix of the container specification, except that the inspection shall be in accordance with 4.4.5. Shipping containers shall be arranged in unit loads in accordance wi
40、th MIL-L-35078, for the type and class of load specified (see 6.2). shall be limited to non-metallic strapping, except for type II, class F loads. Approximate inside dimensions Strapping 5.2.2 Level B packing. Six hundred headbands of one size only preserved as specified in 5.1, shall be packed in a
41、 fiberboard shipping container conforming to style RSC, type CF (variety SW) or SF, class domestic, grade 275 of PPP-B-636. as specified in table II. accordance with method II as specified in the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.4.5. Approximate inside
42、dimensions of each shipping container shall be Each shipping container shall be closed in 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-H-q409BA 84 9 9797706 0366487 3 MIL-H-44098A D 5.2.2.1 Weather-resistant fiberboard container. When spec
43、ified (see 6.2), the fiberboard shipping container shall be a grade VC, VS, or V4s fiberboard box fabricated in accordance with PPP-B-636 an closed in accordance with method III as specified in the appendix of the container specification, except that the inspection shall be in accordance with 4.4.5.
44、 5.2.3 Caimnercial packing. Headbands preserved as specified in 5.1, shall be packed in accordance with ASTM D 3951. 5.3 Palletization. When specified (see 6.2), headbands, packed as specified in 5.2.2 or 5.2.3, shall be palletized in accordance with load type Ia of MIL-STD-147. IV of MIL-STD-731. s
45、econdary straps in accordance with bonding means C and D 01: film bonding means F or G. MIL-STD-147. Pallets shall be fabricated fram wood groups I, II, III or Each prepared load shall be bonded with primary and Pallet pattern shall be number 102 in accordance with the appendix of 5.4 Marking. In ad
46、dition to any special marking required by the contract or purchase order, unit packs, intermediate boxes, shipping containers and palletized unit loads shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. 60 NOTES (This section contains information of a general or explanator
47、y nature that may he helpful, but not mandatory.) 6.1 Intended use. The headband is intended to be used with the Ground Troops - Parachutists Helmet. 6.2 Acquisition requirements. Acquisition documents must specify the fallowing : a. Title, numkr, and data of this specification. b. Size required (se
48、e 1.2) C. Issue of DODISS to be cited in the solicitation, and if required, the d. When a first article is required (see 3.1, 4.3, and 6.3) e. Levels of preservation and packing (see 5.1 and 5.2). f. Type and class of unit load required (see 5.2.1). g. when weather-resistant grade fiberboard shippin
49、g containers are required for level 13 packing (see 5.2.2.1) . h. When palletization is required (see 5.3). specific issue of individual documents referenced (see 2.1.1 and 2.2). 6.3 First article. When a first article is required, it shall be inspected The first article and approved under the appropriate provisions of FAR 52.209. should be a preproduction sample. appropriate type of first article and the number of unit
