1、MIL-L-9353bF 9 M 7797706 0374573 O - MIL-L-43536F 16 June 1989 SUPERSEDING MIL -L -4 35 36 E 7 October 1982 MILITARY SPECIFICATION LINER, COLD WEATHER COAT This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. This specification co
2、vers an insulating liner for the field coat -. made of quilted polyester batting material. 1.2 Classification. The liner shall be of one type in the following sizes, as specified (see 6.2). Schedule of sizes XShor t-X-Small X-Short-Small X-Shr t -Me di um X-Small Small Me di um Large X -Lar ge Benef
3、icial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self- addressed Standardization Document Improvement
4、 Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. F- THIS DOCUMENT CONTAINS 30 PAGES. -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
5、 from IHS-,-,-I_._- MIL-L-4353bF 4 - 9999906 037Y572 2 - MIL -L -4 353 6 F 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless ot
6、herwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). i! SPEC1 F I CAT IONS FEDERAL A-A-203 - Paper, Kraft, Untreated V-B-871 - Button, Se
7、wing Hole, and Button, Staple, (Plastic) V-T -2 80 - Thread, Gimp, Cotton, Buttonhole DDD-L -20 - Label: For Clothing, Equipage, and Tentage, PPP-?3-636 - Boxes , Shipping, Fiberboard (General Use) MILITARY MIL-C-508 - Cloth, Oxford, Nylon, 3 Ounce MIL-B-41826 - Batting, Synthetic Fibers: Polyester
8、, , Jnquilted and Quilted) MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistance Items; Clothing, Personal Equipment and Equipage; General Specification For Polyester-Covered Natural or in Colors MIL-T-43548 - Thread, Polyester Core: Cotton-, Rayon-, or MIL-T-43566 - Tape, Textile, Co
9、tton or Polyester, General Purpose, STAN DARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Mem
10、bers for Containers and Pallets I I I I 1 I 1 I I I l 1 1 1 I I 1 I I I l l 1 I l 1 I I 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-4353bF AL( 777770b 0374573 4 MIL -L -4 35 3 6 F (Unless otherwise indicated, copies of federal and militar
11、y specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) * 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherw
12、ise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY F
13、OR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 191 6 Race Street, Philadelphia, PA 191 03-1 187. ) THE COLOR ASSOCIATION OF THE UNITED STATES, INC, Standard Color Card
14、of America (Standard shades may be available from the Color Association of the United States, Inc., 343 Lexington Avenue, New York, NY 10016-0927. If standard shades are not available from the Color Association, individual color samples may be obtained from the contracting activity or as directed by
15、 the contracting activity . (.Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. also may be available in or through libraries or other informational services.) These documents 2.3 Order of precedence. In the event
16、of a conflict between the text of this document and the references cited herein, the. text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 First article. When specifi
17、ed (see 6.21, a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide samples. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.41, appear in the sample, in which case this document shall govern. Variation fro
18、m this document may 3.3 Material. It is encouraged that recycled material be used when practical as long as it meets the requirements.of this document. 3.3.1 Basic material. The basic material shall be a quilted polyester batting, conforming to type IV, class 1, s.tyle a of MIL-B-41826. 3 Provided b
19、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-V353bF V = 777790b 037V574 b W MIL -L -4 35 3 6 F 3.3.2 Facing and binding. The material for facings, neck buttonhole rein- forcements and binding shall be nylon oxford cloth, 3.0 ounce, Olive Green 106, co
20、nforming to type I, class 2 of MIL-C-508. 3.3.3 Tape. The tape for buttonhole tabs shall be type I, class 3, I-inch width, dyed Olive Drab 7 conforming to MIL-T-43566. 3.3.4 Labels. Each liner shall have an identification label, a size label, and an instruction label conforming to DDD-L-20. Label co
21、lor shall be Medium Green, Cable No. 70034, 70130, or 70131 from the Standard Color Card of America. The labels shall show fastness to laundering. 3.3.4.1 Identification label. The identification label shall conform to type VI, class 1. 3.3.4.2 Size label. The size label shall conform to type VI, cl
22、ass 2 and contain the following information for each respective size: X-Shor t -X-Small X-S hort -Smal 1 Height: Up to 63 inches . Height: Up to 63 inches Chest mens: Up to 33 inches Chest mens: 33 to 37 inches Chest womens: Up to 36 inches Chest womens: 36 to 40 inches Stock No. Stock No. NATO ,. S
23、ize: 5060/7484 NATO Size : 5060/8494 X-S hor t -M ed i um Height: Up to 63 inches Chest mens: 37 to 41 inches Chest womens: 40 to 44 inches Stock No. NATO Size: 5060/9404 Small Height: Over 63 inches Chest mens: 33 to 37 inches Chest womens: 36 to 40 inches Stock No. NATO Size : 7080/8494 Large Heig
24、ht: Over 63 inches Chest mens: 41 to 45 inches Stock No. NATO Size: 7080/0414 4 X-Small Height: Over 63 inches Chest mens: Up to 33 inches Chest womens: Up to 36 inches Stock No. NATO Size: 7080/7484 Medi um Height: Over 63 inches Chest mens: 37 to 41 inches Chest womens: 40 to 44 inches Stock No. N
25、ATO Size : 7080/9404 X-Large Height: Over 63 inches Chest mens: Over 45 inches Stock No, NATO Size; 7080 424 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-L-Y353bF BY M 7777706 037Ll575 W MIL -L -4 35 36F 3,3.4,3 Instruction label. The instruc
26、tion label shall conform to type VI, class 3 and contain the following information: * LINER, COLD WEATHER COAT 1. For extra warmth, button into Coat, Cold Weather, Field, or wear 2. Dry liner and coat separately when damp or wet. 3. Avoid contact with heated stoves, open fires, or other heat 4. as a
27、 separate garment in the Parka, Cold Weather, Camouflage. sources; fabric may fuse. rinse thoroughly, and drip dry or tumble dry, medium setting. DO NOT DRY CLEAN. Wash by hand or machine in warm water with mild soap or detergent, DO NOT REMOVE THIS LABEL 3.3.4.4 Combination size and identification
28、label. The identification label (class 1) and the size label (class 2) may be combined into one label conforming to type VI, classes 1 and 2 combined. 3.3.4.5 Combination size, identification, and instruction label. The identification label (class 11, size label (class 21, and instruction label (cla
29、ss 3) may be combined into one label conforming to class 14. a * 3.3.5 Thread. The thread shall be cotton-covered polyester thread, dyed Olive Drab S-1 , C.A. 66022, ticket numbers 30, 2 or 3 ply; 50, 1 or 3 ply; and 70, 2 or 3 ply conforming to MIL-T-43548. 3.3.5.1 Colorfastness. The dyed thread sh
30、all show fastness to laundering equal to or better than the standard sample. When no standard sample is available, the dyed thread shall show llgoodfl fastness to laundering. 3.3.6 - Gimp. The cotton gimp for reinforcing buttonholes shall be size No, 8, dyed Olive Drab S-1, Cable No. 66022, conformi
31、ng to type I or II of V-T-280. 3.3.6.1 Colorfastness. The dyed gimp shall show fastness to laundering equal to or better than the standard sample. When no standard sample is available, the dyed gimp shall show ligoodll fastness to laundering. * 3.3.7 Buttons. The buttons shall be 30 line, 4 hole, co
32、nforming to type II, The color shall be Olive Green BP and the finish class D, style 26 of V-B-871. shall be dull. 3.4 Figures. Figure 1 is furnished for information only. Should variation from the written specification appear in figure 1, the written specification shall govern. .I e Provided by IHS
33、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43536F 84 W 9799706 0374576 T e MIL -L -4 353 6F 3.5 Patterns. Standard patterns, which provide a 3/8 inch seam allowance for all seams, except the facing and neck buttonhole reinforcement seams which shall be 1
34、/4 inch, will be furnished by the Government. The standard patterns shall not be altered in any way and shall be used as a guide for cutting the contractors working patterns. The working patterns shall be identical to the standard patterns. 3.5.1 Pattern parts. The pattern parts and applicable mater
35、ial for cutting the liner parts shall be as specified in table I. TABLE I. List of pattern parts Materials Nomenclat Ure Cut parts Quilted polyester batting Body Top sleeve Under sleeve 1 2 2 Cloth, nylon, oxford Neck buttonhole reinforcement 1 3.6 Construction. 3.6.1 Stitches , seams, and stitching
36、. Stitch, seam, and stitching types specified in table II shall conform to FED-STD-751. Where two or more seamaor stitching types are given for the same operation, any one of them may be used. Seam allowances shall be maintained with seams sewn so that raw edges, run-Offs, twists, pleats, puckers, o
37、r open seams will not result. Thread tension shall be maintained so that there is no tight or loose stitching. All seams shall start and finish evenly. 3.6.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched not less than 1/4 inch except where ends are turned under or
38、 caught in other seams or stitching. Ends of a continuous line of stitching shall overlap not less than. 1/2 inch. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materia
39、ls sewn. lock shall be embedded in the materials sewn. The 3.6.1.1.1 Repairs of type 301 stitching. 3.6.1.1.1.1 Quilted batting stitching. Broken stitches of the quilting pattern may be repaired by stitching back of each end of break not less than 1 inch. 6 Provided by IHSNot for ResaleNo reproducti
40、on or networking permitted without license from IHS-,-,-MIL-L-q353bF 4 W 77997Ob 0374577 I W MIL -L -4 35 36 F 3.6.1.1.2 Liner fabrication stitching. a. When thread breaks or bobbin run-outs occur during stitching, except prestitching, the stitching shall be repaired by restarting the stitching a mi
41、nimum of 1/2 inch back of the end of the stitching. - 1/ b, Except for prestitching, thread breaks, or two or more consecutive skipped or run-off stitches noted during inspection of the item shall be repaired by overstitching. The stitching shall start a minimum of 1/2 inch in back of the defective
42、area, continue over the defective area, and continue a minimum of 1/2 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials , and resti tching in the required manner. When
43、damaged thread has been removed, needle holes do not constitute damage to the material. - 1/ - 1/ When making the above repairs, the ends of the stitching are not required to be backstitched. 3.6.1.2 Type 301, 401, 504, 505, 515, 516, or 519 stitching. Thread tension shall be maintained so that ther
44、e will be no loose or excessively tight stitching resulting in puckering of the materials sewn. All repairs shall be in accordance with 3.6.1.1.1.2.a. and 3.6.1.1.1.2.b. Type 301 stitching may be used to repair type 401 stitching. 3.6.2 Buttonhole. The buttonholes shall be eyelet-end, taper-bar type
45、 , worked over gimp (see 3.3.6) with not less than four tacking stitches at bar end (not counting crossover stitches), reinforcement side. buttonholes shall be clean cut with the stitching securely caught in the fabric. Additive treatments or materials used to secure the ends of the stitching or to
46、stiffen the fabric, prior to stitching the buttonholes are prohibited. The purling shall be on the facing side and The finished cut lengths shall be 3/11 to 7/8 inches. The 3.6.3 Bartacking. Unless otherwise specified, bartacking shall be as follows : Length Width Stitches per bartack 1/2 inch + 1/1
47、6 inch 3/4 inch - 1/16 inch 1/8 inch + 1/32 inch 1/8 inch 5 1/32 inch - 28 42 Bartacking shall be free from thread breaks. and loose stitching. 3.6.4 Automatic stitching. Automatic stitching machines may be used to perform any of the stitch patterns provided the requirements for the stitch pattern,
48、stitches per inch, and size and type of thread are met; and at least three or more tying, overlapping or back stitches are used to secure the ends of the stitching. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ - MIL-L-4353bF 4 = 7777706 0374578
49、 3 W MIL -L -4 35 36 F 3.6.5 Thread ends. All thread ends shall be trimmed to a length of not more than l/4 inch. 3.7 Repairs. Repairs such as mends, darns, patches, or splices are not permitted on the liner. 3.8 Manufacturing operations requirements The liner shall be manufactured in accordance with the operations requirements specified in table II. The contractor is not required to follow the exact sequence of
