1、s- 1s- MIL-L-43672C AMENDMENT- 1 21 October 1987 MILITARY SPECIFICATION LINER, SNOW CAMOUFLAGE TROUSERS, WHITE, ARCTIC, M-65 This amendment forms a part of Military Specification MIL-L-43672CY dated 19 September 1983, and is approved for use by all Departments and Agencies of the Department of Defen
2、se. PAGE 2 2.1, under Military Specifications: Add: “MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specifications For“. Under Military Standards: Add: “MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood M
3、embers for Containers and Pallets.“ PAGE 14 Table 11, operation 12b: Delete and substitute: “b. Make three horizontal buttonholes on fronts as indicated on patterns Purling shall be on the inside of the (one on right front, two on left front). liner. c. Make a horizontal buttonhole located 1 inch up
4、 from the leg bottom. Locate and make four horizontal buttonholes equally spaced between the waist buttonhole and the leg bottom buttonhole. The edge of the buttonhole eyelet shall be 1/2 inch from the edge of the facing. of the liner.“ Purling shall be on the inside PAGE 22 4.2.4, lines 1 through 9
5、: Delete and substitute: “4.2.4 Packaging examination. The fully packaged end items shall be examined for the defects listed below. shipping containers. packaged. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.“ The lot size shall be expr
6、essed in units of nie sample unit shall be one shipping container fully AMSC H/A Page 1 of 3 FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43672C Amend
7、ment-1 PACE 23 Add new paragraph: “4.2.5 Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged. The in
8、spection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5 Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement. Palletization Pallet pattern not as specified, Interlocking of loads not as specified. Load not bo
9、nded as specified. Weight Exceeds maximum load limits. Marking Omitted; incorrect; illegible; of improper size, location, sequence, or method of application.“ -i 2 5.2.1, at the end of paragraph: Add “Shipping containers shall be arranged in unit loads in accordance with MIL-L-35078 for the type and
10、 class of load speci- fied (see 6.2). type II, class F loads. Strapping shall be limited to nonmetallic strapping, except for PAGE 24 5.2.3: Delete and substitute: “5.2.3 Comercial packing. Liners, preserved as specified in 5.1, shall be packed in accordance with ASTM D 39.“ 2 Provided by IHSNot for
11、 ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 24 (contd) MIL-L-43672C Amendment-1 5,3 and 5.3.1: Delete and substitute: “5.3 Palletization. When specified (see 6.21, liners, packed as specified in 5.2.2 and 5.2.3, shall be palletized on a 4-way entry pallet in acco
12、rdance with load type Ia of MIL-STD-147. Pallet type shall be type I (4-way entry), type IV or type V in accordance with MIL-STD-147. Pallets shall be fabricated from wood groups, I, II, III, or IV of MIL-STD-731. Each prepared load shall be bonded with primary and secondary straps in accordance wit
13、h bonding means K and L or film bonding means O or P. Pallet pattern shall be number 3 in accordance with the appendix of MIL-STD-147. Interlocking of loads shall be effected by reversing the pattern of each course. 5.4 Marking. In addition to any special marking required by the contract or purchase
14、 order, unit packs, shipping containers, and palletized unit loads shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. Each unit pack shall have attached a manilla colored paper shipping tag for the identification marking. 5.4.1 Labels, mixed sizes. Each shipping container
15、packed with mixed sizes shall have securely attached to the end and side, directly under the printing or stenciling, a white paper label 5 by 4 inches with the words “MIXED NSNs“ plainly stamped or printed thereon and under these words shall be legibly stamped or printed the correct quantity and NSN
16、s contained therein.“ PAGE 25 6.2 Add “e. Type and class of unit load required (see 5.2.1). f. When palletization is required (see 5.3).“ Custodians : Preparing Activity: Army - GL Navy - Nu Review activities: Army - MD DLA - CT Army - GL Project No. 8415-0565 User activities: Navy -.MC, YD 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
